Configure Ethernet Service Activation Test

This chapter describes the Cisco IOS XR commands to configure Y.1564 - Ethernet Service Activation Test (SAT).

Understanding Y.1564 - Ethernet Service Activation Test

Table 1. Feature History

Feature Name

Release Information

Feature Description

Y.1564 - Ethernet Service Activation Test (SAT)

Cisco IOS XR Release 6.5.31

Y.1564 – Ethernet SAT is a standards-based test methodology to test turn up, installation, and troubleshooting of Ethernet-based services. This test methodology allows you to measure Frame Transfer Delay (FTD) or latency and Frame Loss Ratio (FLR) parameters.

Commands added:

  • ethernet service-activation-test

  • profile

  • outer-cos

  • duration

  • color-aware

  • information-rate

  • packet-size

  • show ethernet service-activation-test
Table 2. Feature History

Feature Name

Release Information

Feature Description

Y.1564 Ethernet SAT Support on Multi-chassis

Cisco IOS XR Release 6.5.32

Y.1564 – Ethernet SAT feature supports up to four parallel SAT sessions in single chassis and up to four parallel SAT sessions for each rack in multi-chassis.

Ethernet services have evolved significantly with the deployment of Ethernet in service provider networks. Ethernet is not only found at the User Network Interface (UNI) but can also be deployed anywhere in the network, creating a Network-to-Network Interface (NNI). With the capability to prioritize traffic, high availability, and its built-in resiliency, service providers are now using Ethernet technology to deliver advanced services. In the absence of any standardized test methodologies that can measure delay and loss, the ITU-T Y.1564 recommendation addresses this gap.

Y.1564 - Ethernet Service Activation Test (SAT) is a testing procedure which tests service turn-up, installation, and troubleshooting of Ethernet-based services. This test methodology was created to have a standard way of measuring Ethernet-based services in the industry.

Cisco's implementation of ITU-T Y.1564 has three key objectives:

  • Serve as a network service level agreement (SLA) validation tool, ensuring that a service meets its guaranteed performance settings in a controlled test time.

  • Ensure that all the services carried by the network meet their SLA objectives at their maximum committed rate.

  • Perform medium-term and long-term service testing, confirming that network element can properly carry all the services while under stress during a soaking period.

The following Key Performance Indicators (KPI) metrics are collected to ensure that the configured SLAs are met for the service or stream.

  • Frame Transfer Delay (FTD) or latency—Measures the round-trip time (RTT) taken by a test frame to travel through a network device, or across the network and back to the test port.

  • Frame Loss Ratio (FLR)—Measures the number of packets lost from the total number of packets sent. Frame loss can be due to a number of issues such as network congestion or errors during transmissions.


Note

  • Rewrite with POP option is supported with Color Blind mode with Outer-Cos value of 0.

  • Rewrite with POP option is not supported when the second VLAN tag is "any".


Note

The maximum number of parallel SAT sessions supported is four in single chassis and four for each rack in multi-chassis.


Note

If the bundle interface has members on rack 1 and rack 2, the number of parallel SAT sessions supported is two in rack 1 and two in rack 2.

Supported Modes

The mode of operation that is supported for Y.1564 is the two-way statistics collection mode. In the two-way mode, the sender generates the test traffic used to perform the test, which is then looped back by the remote node. The statistics are measured and collected locally on the sender.

The following encapsulations are supported by Y.1564 SAT feature:

  • dot1q

  • dot1q + second dot1q

  • dot1ad

  • dot1ad + second dot1q

  • priority tagged

  • untagged

Supported Bandwidth Parameters

Bandwidth Parameters

Internal Direction

External Direction

Commited Information Rate

Y

Y

Exceeded Information Rate

Y

Y

SAT Target Matrix

Target

Internal Direction

External Direction

L2 Interface over physical main or sub interfaces

Y

Y

L2 Interface over bundle main or sub interfaces

Y

Y

L2 PW VPWS over physical main or sub interfaces

Y

Y

L2 PW VPWS over bundle main or sub interfaces

Y

Y

XConnect over physical main or sub interfaces

Y

Y

XConnect over bundle main or sub interfaces

Y

Y

Configuring Color Profile for Ethernet SAT

The following example shows how to configure a color-blind profile for Ethernet SAT.


RP/0/RP0:hostname#configure
RP/0/RP0:hostname(config)#ethernet service-activation-test 
RP/0/RP0:hostname(config-ethsat)#profile sattest1
RP/0/RP0:hostname(config-ethsat-prf)#outer-cos 4
RP/0/RP0:hostname(config-ethsat-prf)#duration 8 minutes 
RP/0/RP0:hostname(config-ethsat-prf)#information-rate 11800 mbps
RP/0/RP0:hostname(config-ethsat-prf)#packet-size 1000

The following example shows how to configure a color-aware profile for Ethernet SAT.


RP/0/RP0:hostname#configure
RP/0/RP0:hostname(config)#ethernet service-activation-test 
RP/0/RP0:hostname(config-ethsat)#profile sattest3
RP/0/RP0:hostname(config-ethsat-prf)#outer-cos 4
RP/0/RP0:hostname(config-ethsat-prf)#duration 1 minutes 
RP/0/RP0:hostname(config-ethsat-prf)#color-aware cir 7 gbps eir-color cos 1
RP/0/RP0:hostname(config-ethsat-prf)#information-rate 8 gbps
RP/0/RP0:hostname(config-ethsat-prf)#packet-size 1000

Configuration Examples

The following example shows how to start service-activation test on an interface with external direction. 

RP/0/RP0:hostname#ethernet service-activation-test start interface TenGigE 10/0/0/1 profile test destination 00ab.6009.9c3c direction external

The following example shows how to start service-activation test on an interface with internal direction. 

RP/0/RP0:hostname#ethernet service-activation-test start interface TenGigE 10/0/0/1 profile test destination 00ab.6009.9c3c direction internal

The following example shows how to stop service-activation-test on an interface.

RP/0/RP0:hostname#ethernet service-activation-test stop interface TenGigE 10/0/0/1

The following example shows how to stop all service-activation-tests.

RP/0/RP0:hostname#ethernet service-activation-test stop all

Verification

To verify the interfaces on which Y.1564 is enabled, use the show ethernet service-activation-test brief command. The following is a sample output of an enabled device. 

RP/0/RP0:hostname#show ethernet service-activation-test brief
Interface                  Permissions       	   Test Status
--------------------------------------------------------------------------
Bundle-Ether10.1           Internal only       In progress, 1 min(s) left		
Te0/0/0/9.2                External only            None started			
Te0/0/0/9.2                Internal only            Completed