The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This module describes how to configure Synchronous Optical NETwork (SONET). SONET defines optical signals and a synchronous frame structure for multiplexed digital traffic. SONET equipment is generally used in North America.
The transport network using SONET provides much more powerful networking capabilities than existing asynchronous systems.
SONET is a set of standards that define the rates and formats for optical networks specified in GR–253–CORE. SONET is based on a structure that has a basic frame format and speed. The frame format used by SONET is the Synchronous Transport Signal (STS), with STS-1 as the base-level signal at 51.84 Mbps. An STS-1 frame can be carried in an OC-1 signal.
SONET has a hierarchy of signaling speeds.
With Synchronous Transport Signal (STS) Circuit Emulation over Packet (CEP) or STS concatenated CEP mode, if you receive a B3 error, then the Remote Error Indication (REI) won’t be generated. Request for Comments (RFC) reference—RFC 4842.
Prior to Cisco IOS XE Cupertino 17.9.1 release, in V-15 or VC1x mode without or with CEM (SAToP/CEP/CESoP), overhead TX_V5 default value is 1.
From Cisco IOS XE Cupertino 17.9.1 release onwards, when CEM (SAToP (framed or Unframed) and CESoP) is configured for VT-15 or VC1x mode, overhead TX_V5 default value is 2. If CEM isn’t configured or VT CEP is configured, then the default value for V5 Overhead is 1. V5 byte value can be modified according to need using configuration vt <> vt <> overhead v5 <> .
Rate combinations are one port of OC-48 or four ports of OC-12 or OC-3.
Only 16 BERT Patterns can be configured at a time.
VT1.5 VT can’t be configured if VT1.5 T1/DS1 is configured with the same KLM value.
PMON fields aren’t supported for VT1.5 VT and DS3 or T3.
PMON Far-end parameters aren’t supported.
Restrictions on Bandwidth
Total available bandwidth is 10G.
rate OC3| OC12| OC48| OC192The following table shows the bandwidth used by different rates:
|
Rate |
Bandwidth |
|---|---|
|
OC-3 |
155.52 Mbps |
|
OC-12 |
622.08 Mbps |
|
OC-48 |
2.4 Gbps |
Restrictions for Clock Source Configuration
Only four ports can be configured in SONET line for clock source configuration per chassis.
You should configure the clock source line and network-clock sync together to receive the clock from a remote port that is connected to the SONET port.
Restrictions for BER Threshold
The BER threshold value 10e-9 is not supported for the following line, path, and VT BER CLIs on the following interface modules:
Line BER CLIs threshold b2-tca, threshold sd-ber and threshold sf-ber.
PATH BER CLIs threshold b3-ber_sd, threshold b3-ber_sf, and threshold b3-tca.
VT BER CLIs threshold bip2-sd, threshold bip2-sf, and threshold bip2-tca.
Not Supported Interface Modules for the Above BER CLIs
NCS4200-48T3E3-CE
NCS4200-3GMS
NCS4200-1T8S-20CS
NCS4200-1T8S-10CS
SONET Switching is achieved on optical interface modules by circuit emulation. Circuit Emulation (CEM) is a way to carry TDM circuits over packet switched network. CEM embeds TDM bits into packets, encapsulates them into an appropriate header and then sends that through Packet Switched Network (PSN). The receiver side of CEM restores the TDM bit stream from packets.
Modes of CEM:
Structure Agnostic TDM over Packet (SAToP) (RFC 4553) – Structure-Agnostic TDM over Packet (SAToP) mode is used to encapsulate T1 or T3 unstructured (unchannelized) services over packet switched networks. In SAToP mode, the bytes are sent out as they arrive on the TDM line. Bytes do not have to be aligned with any framing.
In this mode, the interface is considered as a continuous framed bit stream. The packetization of the stream is done according to IETF RFC 4553. All signaling is carried transparently as a part of a bit stream.
Circuit Emulation Service over Packet (CEP) (RFC 4842) - CEP mode is used to encapsulate SONET payload envelopes (SPEs) like VT1.5 or VT2 or STS-1 or STS-Nc over packet switched networks. In this mode, the bytes from the corresponding SPE are sent out as they arrive on the TDM line. The interface is considered as a continuous framed bit stream. The packetization of the stream is done according to IETF RFC 4842.
|
Mode |
CEM |
Ports |
|---|---|---|
|
STS-48C |
CEP |
OC-48, OC-192 |
|
STS-12C |
CEP |
OC-12, OC-48, OC-192 |
|
STS-3C |
CEP |
OC-3, OC-12, OC-48, OC-192 |
|
STS-1 |
CEP |
OC-3, OC-12, OC-48, OC-192 |
|
DS3 |
SAToP |
OC-3, OC-12, OC-48, OC-192 |
|
DS3-T1 |
SAToP |
OC-3, OC-12, OC-48, OC-192 |
|
VT 1.5 |
CEP |
OC-3, OC-12, OC-48, OC-192 |
|
VT DS1 |
SAToP |
OC-3, OC-12, OC-48, OC-192 |
Each level of the SONET hierarchy terminates its corresponding fields in the SONET payload, as follows:
A section is a single fiber run that can be terminated by a network element (Line or Path) or an optical regenerator.
The main function of the section layer is to properly format the SONET frames, and to convert the electrical signals to optical signals. Section Terminating Equipment (STE) can originate, access, modify, or terminate the section header overhead.
Line-Terminating Equipment (LTE) originates or terminates one or more sections of a line signal. The LTE does the synchronization and multiplexing of information on SONET frames. Multiple lower-level SONET signals can be mixed together to form higher-level SONET signals. An Add/Drop Multiplexer (ADM) is an example of LTE.
Path-Terminating Equipment (PTE) interfaces non-SONET equipment to the SONET network. At this layer, the payload is mapped and demapped into the SONET frame. For example, an STS PTE can assemble 25 1.544 Mbps DS1 signals and insert path overhead to form an STS-1 signal.
This layer is concerned with end-to-end transport of data.
The following parameters affect SONET configuration at the line and section levels:
 Note |
1 byte, 16 bytes, and 64 bytes are the supported values for J0. |
S1S0 — Sets the SS bits value of the H1 byte in the SONET line overhead.
Loopback — Sets a loopback to test the SONET port.
AIS-Shut — Configures the SONET port to send the Alarm Indication Signal (AIS) at shutdown.
Shut — Disables an interface.
lias —Enables line alarm indication signal.
lrdi — Enables line remote defect indication signal.
pais — Enables path alarm indication signal.
plop — Enables loss of pointer failure signal for a path.
pplm — Enables path payload mismatch indication.
prdi — Enables path remote defect indication signal.
sd-ber — Sets Signal Degrade BER threshold.
line —The link uses the recovered clock from the line.
internal — The link uses the internal clock source. This is the default setting.
The following parameters affect SONET configuration at the path level:
BERT — Starts the BERT test.
Clock — Specifies the clock source for a path.
Exit — Exits from SONET path configuration mode.
Loopback — Sets the entire path in the loopback mode.
Mode — Specifies the path operation mode.
No — Negates a command or sets its defaults.
Overhead — Configures SONET path overhead flags.
Shutdown — Disables the SONET path.
Threshold — Sets the path BER threshold values.
vtg — Sets the VT-15 configuration.
The following parameters affect SONET T1 configuration:
BERT — Starts the BERT test.
Clock — Specifies the clock source for T1 interface.
Description — Specifies the description of the controller.
Framing — Specifies the type of a framing on T1 interface.
Loopback — Sets the T1 interface in the loopback mode.
Shutdown — Disables the T1 interface.
The following parameters affect SONET T3 configuration:
Clock — Specifies the clock source for T3 link.
Description — Specifies the description of the controller.
Framing — Specifies the type of a framing on T3 interface.
Loopback — Sets the T3 link in the loopback mode.
Shutdown — Disables the T3 interface.
The following parameters affect SONET VT configuration:
BERT — Starts the BERT test.
CEM Group — Specifies the time slots for CEM group mapping.
Clock — Specifies the clock source for VT.
Description — Specifies the description of the controller.
Loopback — Sets the VT in the loopback mode.
Overhead — Configures VT line path overhead flags.
Shutdown — Disables the VT interface.
Threshold — Configures the VT threshold values.
Each SFP port (0-7) can be configured as OC-3, OC-12, OC-48, or Gigabit Ethernet. SFP+ port (8) can be configured as OC-192 or 10 Gigabit Ethernet.
You must select the MediaType controller to configure and enter the controller configuration mode.
You must configure the controller as a SONET port.
To configure MediaType Controller, use the following commands:
enable
configure terminal
controller MediaType 0/0/16
mode sonet
endTo configure SONET ports, use the following commands:
enable
configure terminal
controller MediaType 0/0/16
mode sonet
controller sonet 0/0/16
rate OC12
endThis section describes how to manage and monitor SONET.
To configure line and section overhead, use the following commands:
enable
configure terminal
controller MediaType 0/0/16
mode sonet
controller sonet 0/0/16
overhead s1s0 2
overhead j0 tx length 1-byte
endNote |
To restore the system to its default condition, use the no form of the command. |
To configure loopback, use the following commands:
enable
configure terminal
controller sonet 0/0/16
loopback local
endNote |
To restore the system to its default condition, use the no form of the command. |
To configure AIS-Shut, use the following commands:
enable
configure terminal
controller sonet 0/0/16
ais-shut
endNote |
The no ais-shut command will not send AIS. |
To configure Shut, use the following commands:
enable
configure terminal
controller sonet 0/0/16
shutdown
endNote |
Use the no shutdown command to disable the interface. |
To configure alarm reporting, use the following commands:
enable
configure terminal
controller sonet 0/0/16
alarm-report b2-tcs
endNote |
To restore the system to its default condition, use the no form of the command. |
To configure clock, use the following commands:
enable
configure terminal
controller MediaType 0/0/16
mode sonet
controller sonet 0/0/16
clock source line
endNote |
The default mode is internal. |
Note |
To restore the system to its default condition, use the no form of the command. |
Configuring Network-Clock SONET
To configure network-clock SONET, use the following commands:
enable
configure terminal
network-clock input-source 1 controller sonet 0/0/16
endTo configure STS-1 modes, use the following commands:
enable
configure terminal
controller sonet 0/0/16
sts-1 1
mode vt-15
endNote |
|
Note |
To restore the system to its default condition, use the no form of the command. |
To configure DS1/T1 CT3 mode of STS-1, you can configure the T1 link using the following steps:
enable
configure terminal
controller sonet 0/0/16
sts-1 1
mode ct3
t1 1 clock source internal
t1 1 framing unframed
endNote |
To restore the system to its default condition, use the no form of the command. |
To configure STS-Nc - contiguous concatenation, use the following commands:
enable
configure terminal
controller sonet 0/0/16
sts-1 1-3 mode sts-3c
endNote |
To restore the system to its default condition, use the no form of the command. |
Note |
To configure STS-3c or STS-12c, use the numbers as multiples for 3 or 12, respectively. |
The following sample output shows the verification of SONET configuration:
Router#show controllers sonet 0/0/16
SONET 0/0/16 is up. ======> this is the controller/port status.
Hardware is A900-IMA3G-IMSG
Port configured rate: OC3 =======> this is the rate the port is configured on it.
Applique type is Channelized Sonet / SDH
Clock Source is Line ===> the clocking config
Medium info:
Type: Sonet, Line Coding: NRZ,
SECTION:
LOS = 0 LOF = 0 =======> the section level alarm counter (from last clear counters)
SONET Section Tables
INTERVAL CV ES SES SEFS
12:15-12:30 0 0 0 0
12:00-12:15 0 0 0 0
11:45-12:00 15 1 0 0 (Invalid) =======> 1st PMON dataset. The 1st dataset will always be flagged Invalid
Total of Data in Current and Previous Intervals
15 1 0 0 (Invalid) ===> PMON for the port
LINE:
AIS = 0 RDI = 0 REI = 0 BIP(B2) = 0 =======> the line level alarm counter (from last clear counters)
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None =========> present active alarms on the port.
Alarm reporting enabled for: SLOS SLOF SF B2-TCA
BER thresholds: SF = 10e-3 SD = 10e-6 ====> ber thresholds
TCA thresholds: B2 = 10e-6
Rx: S1S0 = 00
K1 = 00, K2 = 00 ===> k1k2 values
J0 = 00
RX S1 = 00
Tx: S1S0 = 00
K1 = 00, K2 = 00
J0 = 00
Tx J0 Length : 64
Tx J0 Trace :
52 6F 75 74 65 72 20 20 20 20 20 20 20 20 20 20 Router
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00 ..
Expected J0 Length : 64
Expected J0 Trace :
52 6F 75 74 65 72 20 20 20 20 20 20 20 20 20 20 Router
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00 ..
Rx J0 Length : 64
Rx J0 Trace :
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 ................
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 ................
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 ................
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 00 ................
SONET Line Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
12:15-12:30 0 0 0 50 0 0 0 0 (FE Invalid)======> The Far End PMON dataset is flagged Invalid due to a Near End alarm.
12:00-12:15 0 0 0 0 0 0 0 0
11:45-12:00 48 1 0 0 53 1 0 0 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
48 1 0 50 53 1 0 0 (NE, FE Invalid)
High Order Path:
PATH 1:
Clock Source is internal ====> path level clock
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0 ======> path layer alarms counter
LOP = 0 PSE = 0 NSE = 0 NEWPTR = 0
LOM = 0 PLM = 0 UNEQ = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None ======> present alarms on the path.
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA
TCA threshold: B3 = 10e-6
Rx: C2 = 00 =====> rx and tx C2 byte..
Tx: C2 = 02
PATH TRACE BUFFER : UNSTABLE
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ……………. ====> path trace of the path
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
SONET Path Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
12:15-12:30 0 0 0 0 0 0 0 389 (FE Invalid)
12:00-12:15 0 0 0 0 0 0 0 0
11:45-12:00 0 1 1 0 0 0 0 900 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 1 1 0 0 0 0 1289 (NE, FE Invalid)
PATH 2:
Clock Source is internal
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0
LOP = 0 PSE = 0 NSE = 0 NEWPTR = 0
LOM = 0 PLM = 0 UNEQ = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: PLOP
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA
TCA threshold: B3 = 10e-6
Rx: C2 = 00
Tx: C2 = 04
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 32 00 00 Router 0/2/0.2..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J1 Length : 64
Expected J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 32 00 00 Router 0/2/0.2..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
PATH TRACE BUFFER : UNSTABLE
Rx J1 Length : 0
Rx J1 Trace
SONET Path Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
12:15-12:30 0 0 0 389 0 0 0 0 (FE Invalid)
12:00-12:15 0 0 0 0 0 0 0 0
11:45-12:00 0 0 0 900 0 0 0 0 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 0 0 1289 0 0 0 0 (NE, FE Invalid)
PATH 3:
Clock Source is internal
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0
LOP = 1 PSE = 0 NSE = 0 NEWPTR = 0
LOM = 0 PLM = 0 UNEQ = 1
Active Defects: None
Detected Alarms: PLOP LOM
Asserted/Active Alarms: PLOP
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA
TCA threshold: B3 = 10e-6
Rx: C2 = 00
Tx: C2 = 02
Tx J1 Length : 64
Tx J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 33 00 00 Router 0/2/0.3..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J1 Length : 64
Expected J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 33 00 00 Router 0/2/0.3..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
PATH TRACE BUFFER : UNSTABLE
Rx J1 Length : 0
Rx J1 Trace
SONET Path Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
12:15-12:30 0 0 0 389 0 0 0 0 (FE Invalid)
12:00-12:15 0 0 0 0 0 0 0 0
11:45-12:00 0 0 0 894 0 0 0 0 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 0 0 1283 0 0 0 0 (NE, FE Invalid)
OC3.STS1 0/0/16 is up. ======> present status of the path
Hardware is A900-IMA3G-IMSG
Applique type is VT1.5 =====> mode of the path
STS-1 1, VTG 1, T1 1 (VT1.5 1/1/1) is down ====> status of the SPE (t1)
VT Receiver has no alarm.
Receiver is getting AIS. ===> alarm of the SPE (t1)
Framing is unframed, Clock Source is Internal =====> framing of the T1, clock of the t1
Data in current interval (230 seconds elapsed):
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavailable Secs
0 Path Failures, 0 SEF/AIS Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavailable Secs
0 Path Failures
Data in Interval 1:
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 14 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 15 Unavailable Secs
1 Path Failures, 0 SEF/AIS Secs
Far End Data
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 4 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 0 Unavailable Secs
0 Path Failures
Total Data (last 1 15 minute intervals):
Near End
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 14 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 15 Unavailable Secs
1 Path Failures, 0 SEF/AIS Secs
Far End
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 4 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins,
4 Errored Secs, 0 Bursty Err Secs, 4 Severely Err Secs, 0 Unavailable Secs
0 Path Failures
STS-1 1, VTG 1, T1 2 (VT1.5 1/1/2) is down
VT Receiver has no alarm.
Receiver is getting AIS.
The following table shows each field and its description.
|
Field |
Description |
|---|---|
|
SONET 0/0/16 is up |
Shows that the SONET controller is operating. The controller's state can be up, down, or administratively down. |
|
Port configured rate: OC3 |
Shows the rate configured on the port. |
|
SECTION: LOS = 0 LOF = 0 BIP = 0 |
Shows the section level alarm counters. |
|
SONET Section Tables: INTERVAL CV ES SES SEFS 05:50-05:58 0 0 0 0 |
Shows the PMON for the port. |
|
LINE: AIS = 0 RDI = 0 REI = 0 BIP(B2) = 0 |
Shows the line level alarm counters. |
|
Asserted/Active Alarms: None |
Shows the active alarms on the port. |
|
BER thresholds: SF = 10e-3 SD = 10e-6 |
Shows BER thresholds. |
|
K1 = 00, K2 = 00 |
Shows the K1 and K2 values. |
|
PATH 1: Clock Source is internal |
Shows the path level clock. |
|
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0 LOP = 0 PSE = 0 NSE = 0 NEWPTR = 0 LOM = 0 PLM = 0 UNEQ = 0 |
Shows the path layer alarm counters. |
|
Active Defects: None Detected Alarms: None Asserted/Active Alarms: None Alarm reporting enabled for: PLOP LOM B3-TCA |
Shows the alarms on the path. |
|
TCA threshold: B3 = 10e-6 Rx: C2 = 00 =====> rx and tx C2 byte.. Tx: C2 = 02 PATH TRACE BUFFER : UNSTABLE |
shows the Rx and Tx C2 bytes. |
|
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ……………. |
Shows the path trace. |
|
OC3.STS1 0/3/3.1 is up. |
Shows the status of the path. |
|
Applique type is VT1.5 |
Shows the mode of the path. |
|
STS-1 1, VTG 1, T1 1 (VT1.5 1/1/1) is down |
Shows the status of SPE (T1). |
|
Receiver is getting AIS. |
Shows the alarm of SPE (T1). |
|
Framing is unframed, Clock Source is Internal |
Shows the framing of T1 and clock of the T1. |
To configure a CEM group for Framed SAToP:
enable
configure terminal
controller mediatype 0/4/16
mode sonet
controller sonet 0/4/16
rate oc12
sts-1 1
mode vt-15
vtg 1 t1 1 cem-group 0 framed
end
To configure VT-15 mode of STS-1 for framed SAToP:
enable
configure terminal
controller mediatype 0/0/16
mode sonet
controller sonet 0/0/16
rate oc3
sts-1 1
mode vt-15
vtg 1 t1 1 cem-group 0 framed
endTo configure DS1/T1 CT3 mode of STS-1 for framed SAToP:
enable
configure terminal
controller mediatype 0/0/16
mode sonet
controller sonet 0/0/16
rate oc3
sts-1 2
mode ct3
t3 framing c-bit
t1 1 cem-group 1 framed
endYou can view the statistics or error count generated on the TDM lines.
To view the statistics or error count generated, use the show controller sonet command:
Router# show controller sonet 0/2/0
SONET 0/2/0 is up.
Hardware is NCS4200-1T8S-10CS
Port configured rate: OC3
Applique type is Channelized Sonet
Clock Source is Internal
Medium info:
Type: Sonet, Line Coding: NRZ,
Alarm Throttling: OFF
SECTION:
LOS = 0 LOF = 0 BIP(B1) = 0
SONET Section Tables
INTERVAL CV ES SES SEFS
12:00-12:07 0 0 0 0
11:45-12:00 15 1 0 0 (Invalid)
Total of Data in Current and Previous Intervals
15 1 0 0 (Invalid)
LINE:
AIS = 0 RDI = 0 REI = 0 BIP(B2) = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA
BER thresholds: SF = 10e-3 SD = 10e-6
TCA thresholds: B1 = 10e-6 B2 = 10e-6
Rx: S1S0 = 00
K1 = 00, K2 = 00
J0 = 00
RX S1 = 00
Tx: S1S0 = 00
K1 = 00, K2 = 00
J0 = 04
Tx J0 Length : 64
Tx J0 Trace :
52 6F 75 74 65 72 20 20 20 20 20 20 20 20 20 20 Router
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00 ..
Expected J0 Length : 64
Expected J0 Trace :
52 6F 75 74 65 72 20 20 20 20 20 20 20 20 20 20 Router
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00 ..
Rx J0 Length : 64
Rx J0 Trace :
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 ................
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 ................
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 ................
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 00 ................
SONET Line Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
12:15-12:30 0 0 0 50 0 0 0 0 (FE Invalid)
12:00-12:15 0 0 0 0 0 0 0 0
11:45-12:00 48 1 0 0 53 1 0 0 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
48 1 0 50 53 1 0 0 (NE, FE Invalid)
High Order Path:
PATH 1:
Clock Source is internal
AIS = 0 RDI = 0 REI = 41350871 BIP(B3) = 9
LOP = 0 PSE = 0 NSE = 0 NEWPTR = 0
LOM = 0 PLM = 0 UNEQ = 1
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA
TCA threshold: B3 = 10e-6
Rx: C2 = 04
Tx: C2 = 04
Tx J1 Length : 64
Tx J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 31 00 00 Router 0/2/0.1..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J1 Length : 64
Expected J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 31 00 00 Router 0/2/0.1..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
PATH TRACE BUFFER : UNSTABLE
Rx J1 Length : 64
Rx J1 Trace
BB 43 45 5F 31 5F 31 20 30 2F 34 2F 33 2E 31 00 .CE_1_1 0/4/3.1.
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
SONET Path Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
12:15-12:30 0 0 0 0 0 0 0 389 (FE Invalid)
12:00-12:15 0 0 0 0 0 0 0 0
11:45-12:00 0 1 1 0 0 0 0 900 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 1 1 0 0 0 0 1289 (NE, FE Invalid)
PATH 2:
Clock Source is internal
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0
LOP = 1 PSE = 0 NSE = 0 NEWPTR = 0
LOM = 0 PLM = 0 UNEQ = 1
Active Defects: None
Detected Alarms: PLOP
Asserted/Active Alarms: PLOP
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA
TCA threshold: B3 = 10e-6
Rx: C2 = 00
Tx: C2 = 04
Tx J1 Length : 64
Tx J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 32 00 00 Router 0/2/0.2..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J1 Length : 64
Expected J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 32 00 00 Router 0/2/0.2..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
PATH TRACE BUFFER : UNSTABLE
Rx J1 Length : 0
Rx J1 Trace
SONET Path Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
12:15-12:30 0 0 0 389 0 0 0 0 (FE Invalid)
12:00-12:15 0 0 0 0 0 0 0 0
11:45-12:00 0 0 0 900 0 0 0 0 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 0 0 1289 0 0 0 0 (NE, FE Invalid)
PATH 3:
Clock Source is internal
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0
LOP = 1 PSE = 0 NSE = 0 NEWPTR = 0
LOM = 0 PLM = 0 UNEQ = 1
Active Defects: None
Detected Alarms: PLOP LOM
Asserted/Active Alarms: PLOP
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA
TCA threshold: B3 = 10e-6
Rx: C2 = 00
Tx: C2 = 02
Tx J1 Length : 64
Tx J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 33 00 00 Router 0/2/0.3..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J1 Length : 64
Expected J1 Trace
52 6F 75 74 65 72 20 30 2F 32 2F 30 2E 33 00 00 Router 0/2/0.3..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
PATH TRACE BUFFER : UNSTABLE
Rx J1 Length : 0
Rx J1 Trace
SONET Path Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
12:15-12:30 0 0 0 389 0 0 0 0 (FE Invalid)
12:00-12:15 0 0 0 0 0 0 0 0
11:45-12:00 0 0 0 900 0 0 0 0 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 0 0 1289 0 0 0 0 (NE, FE Invalid)
SONET 0/2/0.1 T3 is down.
NCS4200-1T8S-10CS
Applique type is T3
Receiver is getting AIS.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Cablelength is 224
BER thresholds: SF = 10e-3 SD = 10e-6
Clock Source is internal
Equipment customer loopback
Data in current interval (390 seconds elapsed):
Near End
0 Line Code Violations, 0 P-bit Coding Violations
0 C-bit Coding Violations, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
389 Unavailable Secs, 0 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
0 Severely Errored Line Secs, 0 Path Failures
0 AIS Defect Secs, 0 LOS Defect Secs
Far End
0 Errored Secs, 0 Severely Errored Secs
0 C-bit Unavailable Secs, 0 Path Failures
0 Code Violations, 0 Service Affecting Secs
Data in Interval 1:
Near End
0 Line Code Violations, 0 P-bit Coding Violations
0 C-bit Coding Violations, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
910 Unavailable Secs, 0 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
0 Severely Errored Line Secs, 1 Path Failures
0 AIS Defect Secs, 0 LOS Defect Secs
Far End
0 Errored Secs, 0 Severely Errored Secs
0 C-bit Unavailable Secs, 0 Path Failures
0 Code Violations, 0 Service Affecting Secs
Total Data (last 1 15 minute intervals):
Near End
0 Line Code Violations, 0 P-bit Coding Violations,
0 C-bit Coding Violations, 0 P-bit Err Secs,
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,
910 Unavailable Secs, 0 Line Errored Secs,
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
0 Severely Errored Line Secs, 1 path failures
0 AIS Defect Secs, 0 LOS Defect Secs
Far End
0 Errored Secs, 0 Severely Errored Secs
0 C-bit Unavailable Secs, 0 Path Failures
0 Code Violations, 0 Service Affecting Secs
T1 1 is up
timeslots:
FDL per AT&T 54016 spec.
No alarms detected.
Framing is ESF, Clock Source is Internal
Data in current interval (250 seconds elapsed):
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable Secs, 0 Stuffed Secs
0 Path Failures, 0 SEF/AIS Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable Secs 0 Path Failures
Data in Interval 1:
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
2 Errored Secs, 0 Bursty Err Secs, 2 Severely Err Secs
0 Unavailable Secs, 0 Stuffed Secs
1 Path Failures, 2 SEF/AIS Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
3 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs
0 Unavailable Secs 0 Path Failures
Total Data (last 1 15 minute intervals):
Near End
0 Line Code Violations,0 Path Code Violations,
0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
2 Errored Secs, 0 Bursty Err Secs, 2 Severely Err Secs
0 Unavailable Secs, 0 Stuffed Secs
1 Path Failures, 2 SEF/AIS Secs
Far End
0 Line Code Violations,0 Path Code Violations
0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
3 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs
0 Unavailable Secs, 0 Path Failures
SONET 0/2/0.2 T3 is down.
Hardware is NCS4200-1T8S-10CS
Applique type is Channelized T3 to T1
Receiver is getting AIS.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Cablelength is 224
BER thresholds: SF = 10e-3 SD = 10e-6
Clock Source is internal
Equipment customer loopback
Data in current interval (400 seconds elapsed):
Near End
0 Line Code Violations, 0 P-bit Coding Violations
0 C-bit Coding Violations, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
399 Unavailable Secs, 0 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
0 Severely Errored Line Secs, 0 Path Failures
0 AIS Defect Secs, 0 LOS Defect Secs
Far End
0 Errored Secs, 0 Severely Errored Secs
0 C-bit Unavailable Secs, 0 Path Failures
0 Code Violations, 0 Service Affecting Secs
Data in Interval 1:
Near End
0 Line Code Violations, 0 P-bit Coding Violations
0 C-bit Coding Violations, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
910 Unavailable Secs, 0 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
0 Severely Errored Line Secs, 1 Path Failures
0 AIS Defect Secs, 0 LOS Defect Secs
Far End
0 Errored Secs, 0 Severely Errored Secs
0 C-bit Unavailable Secs, 0 Path Failures
0 Code Violations, 0 Service Affecting Secs
Total Data (last 1 15 minute intervals):
Near End
0 Line Code Violations, 0 P-bit Coding Violations,
0 C-bit Coding Violations, 0 P-bit Err Secs,
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,
910 Unavailable Secs, 0 Line Errored Secs,
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
0 Severely Errored Line Secs, 1 path failures
0 AIS Defect Secs, 0 LOS Defect Secs
Far End
0 Errored Secs, 0 Severely Errored Secs
0 C-bit Unavailable Secs, 0 Path Failures
0 Code Violations, 0 Service Affecting Secs
T1 1 is up
timeslots:
FDL per AT&T 54016 spec.
No alarms detected.
Framing is ESF, Clock Source is Internal
Data in current interval (250 seconds elapsed):
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable Secs, 0 Stuffed Secs
0 Path Failures, 0 SEF/AIS Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable Secs 0 Path Failures
Data in Interval 1:
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
2 Errored Secs, 0 Bursty Err Secs, 2 Severely Err Secs
0 Unavailable Secs, 0 Stuffed Secs
1 Path Failures, 2 SEF/AIS Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
3 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs
0 Unavailable Secs 0 Path Failures
Total Data (last 1 15 minute intervals):
Near End
0 Line Code Violations,0 Path Code Violations,
0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
2 Errored Secs, 0 Bursty Err Secs, 2 Severely Err Secs
0 Unavailable Secs, 0 Stuffed Secs
1 Path Failures, 2 SEF/AIS Secs
Far End
0 Line Code Violations,0 Path Code Violations
0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
3 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs
0 Unavailable Secs, 0 Path Failures
STS-1 2, T1 1 (CT3 2-1) is down
timeslots:
FDL per ANSI T1.403 and AT&T 54016 spec.
Receiver is getting AIS.
Framing is ESF, Clock Source is Internal
Data in current interval (390 seconds elapsed):
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
389 Unavailable Secs, 0 Stuffed Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable Secs
Data in Interval 1:
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
900 Unavailable Secs, 0 Stuffed Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable Secs
Total Data (last 1 15 minute intervals):
Near End
0 Line Code Violations,0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
900 Unavailable Secs, 0 Stuffed Secs
Far End
0 Line Code Violations,0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable SecsTo view the performance monitoring details on SONET, use the show controller sonet tabular command:
Router#show controllers sonet 0/7/19 tabular
SONET 0/7/19 is up.
Hardware is A900-IMA3G-IMSG NCS4200-3GMS
Port configured rate: OC3
Applique type is Channelized Sonet
Clock Source is Internal
Medium info:
Type: Sonet, Line Coding: NRZ,
Alarm Throttling: OFF
SECTION:
LOS = 0 LOF = 0 BIP(B1) = 0
SONET Section Tables
INTERVAL CV-S ES-S SES-S SEFS-S
11:33-11:47 0 0 0 0 (NE, FE Invalid)
LINE:
AIS = 0 RDI = 0 REI = 0 BIP(B2) = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA
BER thresholds: SF = 10e-3 SD = 10e-6
TCA thresholds: B1 = 10e-6 B2 = 10e-6
Rx: S1S0 = NA
K1 = 00, K2 = 00
J0 = 00
RX S1 = 00
Tx: S1S0 = NA
K1 = 00, K2 = 00
J0 = 04
Tx J0 Length : 64
Tx J0 Trace :
50 45 32 20 20 20 20 20 20 20 20 20 20 20 20 20 PE2
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00 ..
Expected J0 Length : 64
Expected J0 Trace :
50 45 32 20 20 20 20 20 20 20 20 20 20 20 20 20 PE2
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00 ..
Rx J0 Length : 64
Rx J0 Trace :
50 45 32 20 20 20 20 20 20 20 20 20 20 20 20 20 PE2
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 0D 00 ..
SONET Line Tables
INTERVAL CV-L ES-L SES-L UAS-L CV-LFE ES-LFE SES-LFE UAS-LFE
11:33-11:47 0 0 0 0 0 0 0 0 (NE, FE Invalid)
APS
BERSF = 0 BERSD = 0
Active Alarms: None
PATH 1:
Clock Source is internal
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0
LOM = 0 PLM = 0 UNEQ = 0 LOP = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-SF B3-SD B3-TCA
BER threshold: SF = 10e-3 SD = 10e-6
TCA threshold: B3 = 10e-6
Rx: C2 = 04
Tx: C2 = 04
Tx J1 Length : 64
Tx J1 Trace
50 45 32 20 30 2F 37 2F 31 39 2E 31 00 00 00 00 PE2 0/7/19.1....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J1 Length : 64
Expected J1 Trace
50 45 32 20 30 2F 37 2F 31 39 2E 31 00 00 00 00 PE2 0/7/19.1....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Rx J1 Length : 64
Rx J1 Trace
50 45 32 20 30 2F 39 2F 37 2E 31 00 00 00 00 00 PE2 0/9/7.1.....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
SONET Path Tables
INTERVAL CV-P ES-P SES-P UAS-P CV-PFE ES-PFE SES-PFE UAS-PFE
11:33-11:47 0 0 0 0 0 0 0 0 (NE, FE Invalid)
PATH 2:
Clock Source is internal
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0
LOM = 0 PLM = 0 UNEQ = 0 LOP = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-SF B3-SD B3-TCA
BER threshold: SF = 10e-3 SD = 10e-6
TCA threshold: B3 = 10e-6
Rx: C2 = 00
Tx: C2 = 00
Tx J1 Length : 64
Tx J1 Trace
50 45 32 20 30 2F 37 2F 31 39 2E 32 00 00 00 00 PE2 0/7/19.2....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J1 Length : 64
Expected J1 Trace
50 45 32 20 30 2F 37 2F 31 39 2E 32 00 00 00 00 PE2 0/7/19.2....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Rx J1 Length : 0
Rx J1 Trace
SONET Path Tables
INTERVAL CV-P ES-P SES-P UAS-P CV-PFE ES-PFE SES-PFE UAS-PFE
11:47-11:47 0 0 0 0 0 0 0 0 (NE, FE Invalid)
PATH 3:
Clock Source is internal
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 0
LOM = 0 PLM = 0 UNEQ = 0 LOP = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-SF B3-SD B3-TCA
BER threshold: SF = 10e-3 SD = 10e-6
TCA threshold: B3 = 10e-6
Rx: C2 = 00
Tx: C2 = 00
Tx J1 Length : 64
Tx J1 Trace
50 45 32 20 30 2F 37 2F 31 39 2E 33 00 00 00 00 PE2 0/7/19.3....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J1 Length : 64
Expected J1 Trace
50 45 32 20 30 2F 37 2F 31 39 2E 33 00 00 00 00 PE2 0/7/19.3....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Rx J1 Length : 0
Rx J1 Trace
SONET Path Tables
INTERVAL CV-P ES-P SES-P UAS-P CV-PFE ES-PFE SES-PFE UAS-PFE
11:47-11:47 0 0 0 0 0 0 0 0 (NE, FE Invalid)
SONET 0/7/19.1 T3 is up.
Hardware is NCS4200-3GMS
Applique type is T3
No alarms detected.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Cablelength is 224
BER thresholds: SF = 10e-3 SD = 10e-6
Clock Source is internal
Equipment customer loopback
Near End Data
INTERVAL CV-L ES-L SES-L LOSS-L CVP-P CVCP-P ESP-P ESCP-P SESP-P SESCP-P SAS-P AISS-P FC-P UASP-P UASCP-P
11:33-11:47 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 (Invalid)
Far End Data
INTERVAL CVCP-PFE ESCP-PFE SESCP-PFE UASCP-PFE FCCP-PFE SASCP-PFE
11:33-11:47 0 0 0 0 0 0 (Invalid)|
Feature Name |
Release Information |
Description |
|---|---|---|
|
GR-820-CORE specific Performance Monitoring |
Cisco IOS XE Bengaluru 17.5.1 |
The show controller tabular enables you to view the performance monitoring details in tabular form as per GR-820-Core standards. |
To view the performance monitoring details on T3 interface, use the show controller t3 tabular command:
Router#show controllers t3 0/7/12 tabular
T3 0/7/12 is down.
Hardware is A900-IMA3G-IMSG NCS4200-3GMS
Applique type is Subrate T3
Receiver has loss of signal.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Line Code is B3ZS, Cablelength Short less than 225ft
BER thresholds: SF = 10e-3 SD = 10e-6
Clock Source is internal
Equipment customer loopback
Near End Data
INTERVAL CV-L ES-L SES-L LOSS-L CVP-P CVCP-P ESP-P ESCP-P SESP-P SESCP-P SAS-P AISS-P FC-P UASP-P UASCP-P
11:33-11:46 0 779 779 779 0 0 0 0 0 0 0 0 0 779 779 (Invalid)
Far End Data
INTERVAL CVCP-PFE ESCP-PFE SESCP-PFE UASCP-PFE FCCP-PFE SASCP-PFE
11:33-11:46 0 0 0 0 0 0 (Invalid)To view the performance monitoring details on T1 interface, use the show controller t1 tabular command:
Router#show controllers t1 0/7/0 tabular
T1 0/7/0 is down
Applique type is A900-IMA3G-IMSG NCS4200-3GMS
Receiver has loss of signal.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
BER thresholds: SF = 10e-3 SD = 10e-6
Near End Data
INTERVAL CV-L ES-L CV-P ES-P SES-P CSS-P SAS-P UAS-P FC-P
10:48-10:57 0 530 0 0 0 0 0 530 1 (Invalid)
Far End Data
INTERVAL ES-LFE ES-PFE SES-PFE SEFS-PFE CSS-PFE UAS-PFE FC-PFE
10:48-10:57 0 0 0 0 0 0 0 (Invalid)Starting with Cisco IOS XE 17.11.1, you can view the previous day performance monitoring details using the following show controller commands for the T1 or E1, T3 or E3, and SONET controllers.
show controllers sonet
show controllers sonet tabular
show controllers sonet remote performance
show controllers sonet remote performance tabular
router#show controllers sonet 0/3/0
SONET 0/3/0 is down.
Hardware is A900-IMA1Z8S-CXNCS4200-1T8S-10CS
Port configured rate: OC3
Applique type is Channelized Sonet
Clock Source is Internal
Medium info:
Type: Sonet, Line Coding: NRZ,
Alarm Throttling: OFF
SECTION:
LOS = 1 LOF = 0 BIP(B1) = 0
SONET Section Tables
INTERVAL CV ES SES SEFS
06:14-06:24 0 611 611 611
05:59-06:14 0 901 901 901
.............
06:29-06:44 0 901 901 901
06:14-06:29 0 901 901 901 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 87107 87107 87107 (NE, FE Invalid)
Total (Previous Day)
05:29-05:29 0 86494 86494 86494 (NE, FE Invalid)
LINE:
AIS = 0 RDI = 0 REI = 0 BIP(B2) = 0
Active Defects: None
Detected Alarms: SLOS SLOF LAIS
Asserted/Active Alarms: SLOS
............
SONET Line Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
06:14-06:24 0 0 0 611 0 0 0 0
05:59-06:14 0 0 0 901 0 0 0 0
05:44-05:59 0 0 0 901 0 0 0 0
05:29-05:44 0 0 0 901 0 0 0 0
.............
06:14-06:29 0 0 0 901 0 0 0 0 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 0 0 87107 0 0 0 0 (NE, FE Invalid)
Total (Previous Day)
05:29-05:29 0 0 0 86494 0 0 0 0 (NE, FE Invalid)
PATH 1:
Clock Source is internal
AIS = 0 RDI = 0 REI = 0 BIP(B3) = 8
LOM = 0 PLM = 0 UNEQ = 0 LOP = 0
..............
SONET Path Tables
INTERVAL CV ES SES UAS CVFE ESFE SESFE UASFE
06:14-06:24 0 0 0 609 0 0 0 0
05:59-06:14 0 0 0 901 0 0 0 0
05:44-05:59 0 0 0 900 0 0 0 0
05:29-05:44 0 0 0 901 0 0 0 0
...............
06:29-06:44 0 0 0 900 0 0 0 0
06:14-06:29 0 0 0 900 0 0 0 0 (NE, FE Invalid)
Total of Data in Current and Previous Intervals
0 0 0 87045 0 0 0 0 (NE, FE Invalid)
Total (Previous Day)
05:29-05:29 0 0 0 86435 0 0 0 0 (NE, FE Invalid)
PATH 2:
Clock Source is internal
................
SONET 0/3/0.1 PATH is down.
Hardware is A900-IMA1Z8S-CXNCS4200-1T8S-10CS
Applique type is VT1.5
STS-1 1, VTG 1, VT 1 (SONET 0/3/0.1/1/1 VT) is down
VT Receiver has LP_AIS.
cep is configured: FALSE cem_id (0)
fwd_alarm_ais :0 fwd_alarm_rai :0, Clock Source is Internal
BIP2-tca:6, BIP2-sf:3, BIP2-sd:6
Tx V5:2
Rx V5:0
Tx J2 Length=64
TX J2 Trace Buffer:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J2 Length=64
Expected J2 Trace Buffer:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Rx J2 Length=16
RX J2 Trace Buffer:
CRC-7: 0x60 ERROR
C9 79 F7 0F 5F D8 5D D2 D2 7C F6 0E 53 B2 0E 00 .y.._.]..|..S...
Data in curerent interval (610 seconds elapsed)
Near End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 609 Unavailable Secs
Far End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
Data in Interval 1:
Near End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 901 Unavailable Secs
Far End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
................
Data in Interval 96:
Near End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 900 Unavailable Secs
Far End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
Total Data (last 96 fifteen minute intervals):
Near End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 86436 Unavailable Secs
Far End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
Total (Previous Day):
Near End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 86435 Unavailable Secs
Far End
0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
STS-1 1, VTG 1, T1 1 (SONET 0/3/0.1/1/1 T1) is down
timeslots: 1-4
FDL per AT&T 54016 spec.
Receiver is getting AIS.
Framing is ESF, Clock Source is Internal
Data in current interval (610 seconds elapsed):
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
609 Unavail Secs, 0 Stuffed Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs
Data in Interval 1:
Near End
0 Line Code Violations, 0 Path Code Violations
...................
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs
Data in Interval 96:
Near End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
900 Unavail Secs, 0 Stuffed Secs
Far End
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs
Total Data (last 24 hours)
Near End
0 Line Code Violations,0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
86436 Unavail Secs, 0 Stuffed Secs
Far End
0 Line Code Violations,0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable Secs
Total (Previous Day)
Near End
0 Line Code Violations,0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
86435 Unavail Secs, 0 Stuffed Secs
Far End
0 Line Code Violations,0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavailable Secs
STS-1 1, VTG 1, VT 2 (SONET 0/3/0.1/1/2 VT) is down
VT Receiver has LP_AIS.
router#show controllers sonet 0/3/0 tabular
Section/Line/Path same as previous.
SONET 0/3/0.1 PATH is down.
Hardware is A900-IMA1Z8S-CXNCS4200-1T8S-10CS
Applique type is VT1.5
STS-1 1, VTG 1, VT 1 (SONET 0/3/0.1/1/1 VT) is down
VT Receiver has LP_AIS.
cep is configured: FALSE cem_id (0)
fwd_alarm_ais :0 fwd_alarm_rai :0, Clock Source is Internal
BIP2-tca:6, BIP2-sf:3, BIP2-sd:6
Tx V5:2
Rx V5:0
Tx J2 Length=64
TX J2 Trace Buffer:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Expected J2 Length=64
Expected J2 Trace Buffer:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Rx J2 Length=16
RX J2 Trace Buffer:
CRC-7: 0x60 ERROR
C9 79 F7 0F 5F D8 5D D2 D2 7C F6 0E 53 B2 0E 00 .y.._.]..|..S...
INTERVAL CV-V ES-V SES-V UAS-V CV-VFE ES-VFE SES-VFE UAS-VFE
06:14-06:24 0 0 0 619 0 0 0 0
05:59-06:14 0 0 0 901 0 0 0 0
05:44-05:59 0 0 0 900 0 0 0 0
05:29-05:44 0 0 0 901 0 0 0 0
05:14-05:29 0 0 0 900 0 0 0 0
04:59-05:14 0 0 0 900 0 0 0 0
...................
06:44-06:59 0 0 0 901 0 0 0 0
06:29-06:44 0 0 0 900 0 0 0 0
06:14-06:29 0 0 0 900 0 0 0 0 (NE, FE Invalid)
Total 0 0 0 86436 0 0 0 0 (NE, FE Invalid)
Total (Previous Day):
05:29-05:29 0 0 0 86435 0 0 0 0 (NE, FE Invalid)
STS-1 1, VTG 1, T1 1 (SONET 0/3/0.1/1/1 T1) is down
timeslots: 1-4
FDL per AT&T 54016 spec.
Receiver is getting AIS.
Framing is ESF, Clock Source is Internal
Near End Data
INTERVAL CV-L ES-L CV-P ES-P SES-P CSS-P SAS-P UAS-P FC-P
06:14-06:24 0 0 0 0 0 0 0 619 0
05:59-06:14 0 0 0 0 0 0 0 901 0
..............
06:44-06:59 0 0 0 0 0 0 0 901 0
06:29-06:44 0 0 0 0 0 0 0 900 0
06:14-06:29 0 0 0 0 0 0 0 900 0 (Invalid)
Total 0 0 0 0 0 0 0 86436 0 (Invalid)
Total (Previous Day):
05:29-05:29 0 0 0 0 0 0 0 86435 0 (Invalid)
Far End Data
INTERVAL ES-LFE ES-PFE SES-PFE SEFS-PFE CSS-PFE UAS-PFE FC-PFE
06:14-06:24 0 0 0 0 0 0 0
05:59-06:14 0 0 0 0 0 0 0
......................
06:29-06:44 0 0 0 0 0 0 0
06:14-06:29 0 0 0 0 0 0 0 (Invalid)
Total 0 0 0 0 0 0 0 (Invalid)
Total (Previous Day):
05:29-05:29 0 0 0 0 0 0 0 (Invalid)
STS-1 1, VTG 1, VT 2 (SONET 0/3/0.1/1/2 VT) is down
VT Receiver has LP_AIS.
cep is configured: FALSE cem_id (0)
fwd_alarm_ais :0 fwd_alarm_rai :0, Clock Source is Internal
router#show controllers sonet 0/3/0 remote performance
Section/Line/Path same as previous.
SONET 0/3/0.1 PATH is down.
Hardware is A900-IMA1Z8S-CXNCS4200-1T8S-10CS
STS-1 1, VTG 1, VT 1 (VT1.5 1/1/1) - Remote Performance Data
Far end MIB Data:
Data in curerent interval (630 seconds elapsed)
0 CodeViolations , 0 ErrorSecs,0 Severly Err Secs, 0 Unavail Secs
FarEnd VT Interval data:
Total Data (last 96 15 minute intervals):
0 CodeViolations, 0 ErrorSec, 0 Severly Err Secs, 0 Unavail Secs
Total (Previous Day):
0 CodeViolations, 0 ErrorSec, 0 Severly Err Secs, 0 Unavail Secs
STS-1 1, VTG 1, T1 1 (SONET 0/3/0.1/1/1 T1) - Remote Performance Data
Data in current interval (630 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs
Data in Interval 1:
.................
Data in Interval 96:
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs
Total Data (last 24 hours)
0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs
Total (Previous Day)
0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs
STS-1 1, VTG 1, VT 2 (VT1.5 1/1/2) - Remote Performance Data
Far end MIB Data:
Data in curerent interval (630 seconds elapsed)
0 CodeViolations , 0 ErrorSecs,0 Severly Err Secs, 0 Unavail Secs
FarEnd VT Interval data:
Total Data (last 96 15 minute intervals):
0 CodeViolations, 0 ErrorSec, 0 Severly Err Secs, 0 Unavail Secs
Total (Previous Day):
0 CodeViolations, 0 ErrorSec, 0 Severly Err Secs, 0 Unavail Secs
router#show controllers sonet 0/3/0 remote performance tabular
Section/Line/Path same as previous.
SONET 0/3/0.1 PATH is down.
Hardware is A900-IMA1Z8S-CXNCS4200-1T8S-10CS
STS-1 1, VTG 1, VT 1 (VT1.5 1/1/1) - Remote Performance Data
Far end MIB Data:
INTERVAL CV ES SES UAS
06:14-06:24 0 0 0 0
FarEnd VT Interval data:
INTERVAL CV ES SES UAS
05:59-06:14 0 0 0 0
05:44-05:59 0 0 0 0
05:29-05:44 0 0 0 0
05:14-05:29 0 0 0 0
.................
06:29-06:44 0 0 0 0
06:14-06:29 0 0 0 0
Total
CV ES SES UAS 0 0 0 0
Total (Previous Day)
CV ES SES UAS 0 0 0 0
STS-1 1, VTG 1, T1 1 (SONET 0/3/0.1/1/1 T1) - Remote Performance Data
INTERVAL LCV PCV CSS SELS LES DM ES BES SES UAS
06:14-06:24 0 0 0 0 0 0 0 0 0 0
05:59-06:14 0 0 0 0 0 0 0 0 0 0
05:44-05:59 0 0 0 0 0 0 0 0 0 0
....................
06:44-06:59 0 0 0 0 0 0 0 0 0 0
06:29-06:44 0 0 0 0 0 0 0 0 0 0
06:14-06:29 0 0 0 0 0 0 0 0 0 0
Total 0 0 0 0 0 0 0 0 0 0 (NE, FE Invalid)
Total (Previous Day)
05:29-05:29 0 0 0 0 0 0 0 0 0 0 (NE, FE Invalid)
STS-1 1, VTG 1, VT 2 (VT1.5 1/1/2) - Remote Performance Data
Far end MIB Data:
INTERVAL CV ES SES UAS
06:14-06:24 0 0 0 0 (Invalid)
FarEnd VT Interval data:
INTERVAL CV ES SES UAS
05:59-06:14 0 0 0 0 (Invalid)
A comprehensive range of pluggable optical modules is available. For more information, see Cisco NCS 4200 Series - Supported Optics.
To configure port rate for SONET, use the following commands:
enable
configure terminal
controller mediatype 0/0/16
mode sonet
exit
controller sonet 0/0/16
rate oc3Before you configure the pluggables, use the following commands to verify the supported plugables:
show hw-module subslot <slot/bay> transceiver <port> status:
The Transceiver in slot 0 subslot 7 port 4 is enabled.
Module temperature = +46.636 C
Transceiver Tx supply voltage = 3291.5 mVolts
Transceiver Tx bias current = 17264 uAmps
Transceiver Tx power = -2.9 dBm
Transceiver Rx optical power = -7.4 dBm
Note |
The show hw-module subslot <slot/bay> transceiver <port> status displays as Enabled if the pluggables are supported and the command displays as Disabled if the pluggables are not supported. |
show hw-module subslot <slot/bay> transceiver <port> idprom:
show hw-module subslot 0/7 transceiver 6 idprom detail
IDPROM for transceiver SPA-1T8S-10CS_7/6:
Description = SFP or SFP+ optics (type 3)
Transceiver Type: = ONS SE Z1 (406)
Product Identifier (PID) = ONS-SE-Z1
Vendor Revision = A
Serial Number (SN) = FNS19251NPM
Vendor Name = CISCO-FINISAR
Vendor OUI (IEEE company ID) = 00.90.65 (36965)
CLEI code = WMOTCZPAAA
Cisco part number = 10-1971-04
Device State = Enabled.
Date code (yy/mm/dd) = 15/06/19
Connector type = LC.
Encoding = 8B10B
NRZ
Manchester
Nominal bitrate = OC48/STM16 (2500 Mbits/s)
Minimum bit rate as % of nominal bit rate = not specified
Maximum bit rate as % of nominal bit rate = not specified
The transceiver type is 406
Link reach for 9u fiber (km) = IR-1(15km) (15)
Link reach for 50u fiber (m) = SR(2km) (0)
IR-1(15km) (0)
IR-2(40km) (0)
LR-1(40km) (0)
LR-2(80km) (0)
LR-3(80km) (0)
DX(40KM) (0)
HX(40km) (0)
ZX(80km) (0)
VX(100km) (0)
1xFC, 2xFC-SM(10km) (0)
ESCON-SM(20km) (0)
Link reach for 62.5u fiber (m) = SR(2km) (0)
IR-1(15km) (0)
IR-2(40km) (0)
LR-1(40km) (0)
LR-2(80km) (0)
LR-3(80km) (0)
DX(40KM) (0)
HX(40km) (0)
ZX(80km) (0)
VX(100km) (0)
1xFC, 2xFC-SM(10km) (0)
ESCON-SM(20km) (0)
Nominal laser wavelength = 1310 nm.
DWDM wavelength fraction = 1310.0 nm.
Supported options = Tx disable
Tx fault signal
Loss of signal (standard implementation)
Supported enhanced options = Alarms for monitored parameters
Software Rx LOS monitoring
Diagnostic monitoring = Digital diagnostics supported
Diagnostics are externally calibrated
Rx power measured is "Average power"
Transceiver temperature operating range = -40 C to 85 C (industrial)
Minimum operating temperature = -40 C
Maximum operating temperature = 85 C
High temperature alarm threshold = +90.000 C
High temperature warning threshold = +85.000 C
Low temperature warning threshold = -40.000 C
Low temperature alarm threshold = -45.000 C
High voltage alarm threshold = 3630.0 mVolts
High voltage warning threshold = 3470.0 mVolts
Low voltage warning threshold = 3140.0 mVolts
Low voltage alarm threshold = 2971.2 mVolts
High laser bias current alarm threshold = 85.000 mAmps
High laser bias current warning threshold = 65.000 mAmps
Low laser bias current warning threshold = 4.000 mAmps
Low laser bias current alarm threshold = 2.000 mAmps
High transmit power alarm threshold = 4.0 dBm
High transmit power warning threshold = 2.0 dBm
Low transmit power warning threshold = -7.0 dBm
Low transmit power alarm threshold = -9.0 dBm
High receive power alarm threshold = 1.0 dBm
Low receive power alarm threshold = -26.0 dBm
High receive power warning threshold = -1.0 dBm
Low receive power warning threshold = -24.9 dBm
External Calibration: bias current slope = 1.000
External Calibration: bias current offset = 0
show hw-module subslot <slot/bay> transceiver <port> idprom brief:
sh hw-module subslot 0/7 transceiver 6 idprom brief
IDPROM for transceiver SPA-1T8S-10CS_7/6:
Description = SFP or SFP+ optics (type 3)
Transceiver Type: = ONS SE Z1 (406)
Product Identifier (PID) = ONS-SE-Z1
Vendor Revision = A
Serial Number (SN) = FNS19251NQ0
Vendor Name = CISCO-FINISAR
Vendor OUI (IEEE company ID) = 00.90.65 (36965)
CLEI code = WMOTCZPAAA
Cisco part number = 10-1971-04
Device State = Enabled.
Date code (yy/mm/dd) = 15/06/19
Connector type = LC.
Encoding = 8B10B
NRZ
Manchester
Nominal bitrate = OC48/STM16 (2500 Mbits/s)
Minimum bit rate as % of nominal bit rate = not specified
Maximum bit rate as % of nominal bit rate = not specified
The remote loopback configuration attempts to put the far-end T1 or T3 into a loopback.
The remote loopback setting loops back the far-end at line or payload, using IBOC (inband bit-orientated CDE) or the ESF loopback codes to communicate the request to the far-end.
E1 and E3 loopback remote are not supported until Cisco IOS XE Fuji 16.9.4 release. Starting from Cisco IOS XE Fuji 16.9.5 release, E1 and E3 loopback remote are supported.
IBOC loopcode configuration is not supported when CESoP or SATOP (framed or unframed) is configured.
ESF loopcode configuration is not supported when SAToP is configured.
To set T1 loopback remote iboc fac1/fac2/csu for OCX sonet, perform the following tasks in global configuration mode:
enable
configure terminal
controller sonet 0/0/1
mode ct3
t1 1 loopback remote iboc {fac1 | fac2 | csu}
mode vt-15
vtg 1 t1 1 loopback remote iboc {fac1 | fac2 | csu}
To set T1 loopback remote iboc esf line csu/esf payload for OCX sonet, perform the following tasks in global configuration mode:
enable
configure terminal
controller sonet 0/0/1
mode ct3
t1 1 loopback remote iboc esf {line csu | payload}
mode vt-15
vtg 1 t1 1 loopback remote esf {line csu | payload}
To set T3 loopback remote line/payload for OCX in sonet, perform the following tasks in global configuration mode:
enable
configure terminal
controller sonet 0/0/1
mode t3
t3 loopback remote {line | payload}
Note |
loopback remote esf line niu is not supported. |
Use the following command to check the T1 loopback remote configuration:
router# show run | sec 0/0/1
controller SONET 0/0/1
rate OC3
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
!
sts-1 2
clock source internal
mode ct3
t3 framing c-bit
t3 clock source internal
t1 1 Loopback remote iboc fac1
t1 1 framing SF
Use the following command to verify the T1 loopback remote configuration:
Router(config-ctrlr-sts1)# show controller sonet 0/0/1 | b STS-1 2, T1 1
STS-1 2, T1 1 (CT3 2-1) is up
timeslots:
Configured for NIU FAC1 Line Loopback with IBOC
Currently in Inband Remotely Line Looped
Receiver has no alarms.
Framing is SF, Clock Source is Internal
Use the following command to check T3 loopback remote configuration:
Router# show run | sec 0/0/1
controller SONET 0/0/1
rate OC3
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
!
sts-1 2
!
sts-1 3
clock source internal
mode t3
t3 framing c-bit
t3 loop remote line
t3 clock source internal
Use the following command to verify T3 loopback remote configuration:
Router(config-ctrlr-sts1)# do show controller sonet 0/0/1 | b Path 3
OC3.STS1 0/0/1 Path 3 is up. (Configured for Remotely Looped)
Currently in Remotely Line Looped
Hardware is NCS4200-1T8S-10CS
Applique type is T3
Receiver has no alarms.
MDL transmission is disabled
Scrambling is designed to randomize the pattern of 1s and 0s carried in the physical layer frame. Randomizing the digital bits can prevent continuous, non-variable bit patterns. SONET payload scrambling applies a self-synchronous scrambler to the Synchronous Payload Envelope (SPE) of the interface to ensure sufficient bit transition density. You can enable or disable SONET payload scrambling on a concatenated serial interface (POS).
To configure SONET controller, enter the following commands:
Router(config)#controller media 0/4/3
Router(config-controller)#mode sonet
Router(config-controller)#controller sonet 0/4/3
Router(config-controller)#rate oc3
Router(config-controller)#sts
Router(config-controller)#sts 1 - 3 mode sts-3c
Router(config-ctrlr-sts3c)#channel-group 0
Router(config-ctrlr-sts3c)#end
To enable scrambling on a serial interface for the SONET controller, enter the following commands:
Router(config)#interface Serial0/4/3.1
Router(config-if)#pos scramble
Router(config-if)#end
To disable scrambling on a serial interface for the SONET controller, enter the following commands:
Router(config)#interface Serial0/4/3.1
Router(config-if)#no pos scramble
Router(config-if)#end
Use the following commands to verify the POS scrambling configuration:
Router#show ip interface brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned YES unset down down
GigabitEthernet0/0/1 unassigned YES unset down down
GigabitEthernet0/0/2 unassigned YES unset down down
GigabitEthernet0/0/3 unassigned YES unset up up
GigabitEthernet0/0/4 unassigned YES unset down down
GigabitEthernet0/0/5 unassigned YES unset down down
GigabitEthernet0/0/6 unassigned YES unset down down
GigabitEthernet0/0/7 unassigned YES unset down down
GigabitEthernet0/5/0 unassigned YES unset up up
GigabitEthernet0/5/1 unassigned YES unset down down
GigabitEthernet0/5/2 unassigned YES unset down down
GigabitEthernet0/5/3 unassigned YES unset down down
GigabitEthernet0/5/4 unassigned YES unset down down
GigabitEthernet0/5/5 unassigned YES unset down down
GigabitEthernet0/5/6 unassigned YES unset down down
GigabitEthernet0/5/7 unassigned YES unset down down
GigabitEthernet0 7.19.26.14 YES manual up up
Serial0/4/3.1 30.30.30.1 YES manual up up
Feedback