Contents

Detecting and Analyzing Network Threats With NetFlow

This document contains information about and instructions for detecting and analyzing network threats such as denial of service attacks (DoS) through the use of the following NetFlow features:

  • NetFlow Layer 2 and Security Monitoring Exports--This feature improves your ability to detect and analyze network threats such as denial of service attacks (DoS) by adding 9 fields that NetFlow can capture the values from.A few examples are:
    • IP Time-to-Live field
    • Packet length field
    • ICMP type and code fields
  • NetFlow Dynamic Top Talkers CLI--This feature gives you an overview of the highest volume traffic in your network by aggregating flows on a common field. For example, you can aggregate all of the flows for a destination network by aggregating them on the destination prefix. There are over 20 fields from flows that you can aggregate the highest volume traffic on. A few examples are:
    • Source or destination IP address
    • Source or destination prefix
    • Source or destination port
    • ICMP type and code
  • NetFlow Top Talkers--This feature gives you a more detailed view of the traffic in your network than the NetFlow Dynamic Top Talkers CLI feature because it looks at individual flows. You use the NetFlow Dynamic Top Talkers CLI feature to quickly identify high volume traffic of interest. You use the NetFlow Top Talkers feature to obtain more detailed information on each of the flows in the high volume traffic.

  • NetFlow Input Filters--This feature tracks a specific subset of NetFlow traffic for the purpose of class-based traffic analysis and monitoring. This feature is used in conjunction with the Top Talkers feature to help you focus your analysis on the traffic that might be a network threat such as a DoS attack.

  • Random Sampled NetFlow--This feature is typically used for statistical sampling of network traffic for traffic engineering or capacity planning purposes. It is used in the context of monitoring and analyzing network threats because it can be used to reduce the impact on the router using NetFlow to monitor traffic that might be a network threat, such as a DoS attack.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for Detecting and Analyzing Network Threats With NetFlow

Before you can use NetFlow for detecting and analyzing network threats you need to understand NetFlow and how to configure your router to capture IP traffic status and statistics using NetFlow. See the Cisco IOS NetFlow Overview and Configuring NetFlow and NetFlow Data Export modules for more details.

NetFlow and Cisco Express Forwarding (CEF) or distributed CEF (dCEF) must be configured on your system before you enable NetFlow.

Information About Detecting and Analyzing Network Threats With NetFlow

NetFlow Layer 2 and Security Monitoring

The Layer 2 and Layer 3 fields supported by the NetFlow Layer 2 and Security Monitoring Exports feature increase the amount of information that can be obtained by NetFlow about the traffic in your network. You can use the network traffic information for applications such as traffic engineering and usage-based billing.

Layer 3 fields captured by the NetFlow Layer 2 and Security Monitoring Exports feature improve the capabilities of NetFlow for identifying DoS attacks. Layer 2 IP header fields help identify the path that the DoS attack is taking through the network.

Layer 2 and Layer 3 fields are not key fields. They provide additional information about the traffic in an existing flow. Changes in the values of NetFlow key fields, such as the source IP address, from one packet to the next packet results in the creation of a new flow. For example, if the first packet captured by NetFlow has a source IP address of 10.34.0.2 and the second packet captured has a source IP address of 172.16.213.65, NetFlow will create two separate flows.

Most DoS attacks consist of an attacker sending the same type of IP datagram repeatedly, in an attempt to overwhelm target systems. In such cases, the incoming traffic often has similar characteristics, such as the same values in each datagram for one or more fields that the NetFlow Layer 2 and Security Monitoring Exports feature can capture.

The originator of DoS attacks cannot be easily identified because the IP source address of the device sending the traffic is usually forged. However, you can easily trace the traffic back through the network to the router on which it is arriving by using the NetFlow Layer 2 and Security Monitoring Exports feature to capture the MAC address and VLAN-ID fields. If the router on which traffic is arriving supports NetFlow, you can configure the NetFlow Layer 2 and Security Monitoring Exports feature on it to identify the interface on which the traffic is arriving. The figure below shows an example of an attack in progress.

Figure 1. DoS Attack Arriving over the Internet


Note


You can analyze the data captured by NetFlow directly from the router by using the show ip cache verbose flow command or by the Cisco Network Services (CNS) NetFlow Collector Engine.


Once you have concluded that a DoS attack is taking place by analyzing the Layer 3 fields in the NetFlow flows, you can analyze the Layer 2 fields in the flows to discover the path that the DoS attack is taking through the network.

An analysis of the data captured by the NetFlow Layer 2 and Security Monitoring Exports feature, for the scenario shown in the above figure, indicates that the DoS attack is arriving on Router C, because the upstream MAC address is from the interface that connects Router C to Switch A. It is also evident that there are no routers between the target host (the e-mail server) and the NetFlow router, because the destination MAC address of the DoS traffic that the NetFlow router is forwarding to the e-mail server is the MAC address of the e-mail server.

You can learn the MAC address that Host C is using to send traffic to Router C by configuring the NetFlow Layer 2 and Security Monitoring Exports feature on Router C. The source MAC address will be from Host C. The destination MAC address will be for the interface on the NetFlow router.

Once you know the MAC address that Host C is using and the interface on Router C on which Host C’s DoS attack is arriving, you can mitigate the attack by reconfiguring Router C to block Host C’s traffic. If Host C is on a dedicated interface, you can disable the interface. If Host C is using an interface that carries traffic from other users, you must configure your firewall to block Host C’s traffic, but still allow the traffic from the other users to flow through Router C.

Layer 3 Information Capture Using NetFlow Layer 2 and Security Monitoring Exports

The five fields that the NetFlow Layer 2 and Security Monitoring Exports feature captures from Layer 3 IP traffic in a flow are the following:

  • Internet Control Message Protocol (ICMP) type and code

  • ID field

  • Fragment offset

  • Packet length field

  • Time-to-live field

Figure 5 shows the fields in an IP packet header.

Figure 2. IP Packet Header Fields

Table 4 describes the header fields in Figure 5.

Table 1 IP Packet Header Fields

Field

Description

Version

The version of the IP protocol. If this field is set to 4, it is an IPv4 datagram. If this field is set to 6, it is an IPv6 datagram.

Note   

IPv4 and IPv6 headers have different structures.

IHL (Internet Header Length)

Internet Header Length is the length of the Internet header in 32-bit word format and thus points to the beginning of the data.

Note   

The minimum value for the correct header length is 5.

ToS

Type of service (ToS) provides an indication of the abstract parameters of the quality of service desired. These parameters are to be used to guide the selection of the actual service parameters when a networking device transmits a datagram through a particular network.

Total Length

Total length is the length of the datagram, measured in octets, including Internet header and data.

Identification (ID)

The value in the ID field is entered by the sender. All the fragments of an IP datagram have the same value in the ID field. Subsequent IP datagrams from the same sender will have different values in the ID field.

Frequently, a host receives fragmented IP datagrams from several senders concurrently. Also, frequently a host receives multiple IP datagrams from the same sender concurrently.

The value in the ID field is used by the destination host to ensure that the fragments of an IP datagram are assigned to the same packet buffer during the IP datagram reassembly process. The unique value in the ID field is used to prevent the receiving host from mixing together IP datagram fragments of different IP datagrams from the same sender during the IP datagram reassembly process.

Flags

A sequence of three bits is used to set and track IP datagram fragmentation parameters. The bits are:

  • 001—The IP datagram can be fragmented. More fragments of the current IP datagram are in transit.

  • 000—The IP datagram can be fragmented. This is the last fragment of the current IP datagram.

  • 010—The IP datagram cannot be fragmented. This is the entire IP datagram.

Fragment Offset

This field indicates where in the datagram this fragment belongs.

TTL (Time-to-Live)

This field indicates the maximum time the datagram is allowed to remain in the Internet system. If this field contains the value 0, then the datagram must be destroyed. This field is modified in Internet header processing. The TTL is measured in units of seconds, but because every module that processes a datagram must decrease the TTL by at least 1 even if it processes the datagram in less than a second, the TTL must be thought of only as an upper bound on the time a datagram can exist. The intention is to discard undeliverable datagrams and bound the maximum datagram lifetime.

Protocol

Indicates the type of transport packet included in the data portion of the IP datagram. Common values are:

  • 1—ICMP

  • 6—TCP

  • 17—UDP

Header checksum

A checksum on the header only. Because some header fields, such as the TTL field, change every time an IP datagram is forwarded, this value is recomputed and verified at each point that the Internet header is processed.

Source IP Address

IP address of the sending station.

Destination IP Address

IP address of the destination station.

Options and Padding

The options and padding may appear in datagrams. If they do appear, they must be implemented by all IP modules (host and gateways). Options and padding are always implemented in any particular datagram; transmissions are not.

Figure 6 shows the fields in an ICMP datagram.

Figure 3. ICMP Datagram

Table 5 interprets the packet format in the figure seen above. ICMP datagrams are carried in the data area of an IP datagram, after the IP header.

Table 2 ICMP Packet Format

Type

Name

Codes

0

Echo reply

0—None.

1

Unassigned

2

Unassigned

3

Destination unreachable

0—Network unreachable.

1—Host unreachable.

2—Protocol unreachable.

3—Port unreachable.

4—Fragmentation needed and don't fragment (DF) bit set.

5—Source route failed.

6—Destination network unknown.

7—Destination host unknown.

8—Source host isolated.

9—Communication with the destination network is administratively prohibited.

10—Communication with the destination host is administratively prohibited.

11—Destination network unreachable for ToS.

12—Destination host unreachable for ToS.

4

Source quench

0—None.

5

Redirect

0—None.

0—Redirect datagram for the network.

1—Redirect datagram for the host.

2—Redirect datagram for the ToS and network.

3—Redirect datagram for the ToS and host.

6

Alternate host address

0—Alternate address for the host.

7

Unassigned

8

Echo

0—None.

9

Router advertisement

0—None.

10

Router selection

0—None.

11

Time exceeded

0—Time to live exceeded in transit.

12

Parameter problem

0—Pointer indicates the error.

1—Missing a required option.

2—Inappropriate length.

13

Timestamp

0—None.

14

Timestamp reply

0—None.

15

Information request

0—None.

16

Information reply

0—None.

17

Address mask request

0—None.

18

Address mask reply

0—None.

19

Reserved (for security)

20–29

Reserved (for robustness experiment)

30

Trace route

31

Datagram conversion error

32

Mobile host redirect

33

IPv6 where-are-you

34

IPv6 I-am-here

35

Mobile registration request

36

Mobile registration reply

37–255

Reserved

Layer 2 Information Capture Using NetFlow Layer 2 and Security Monitoring Exports

The NetFlow Layer 2 and Security Monitoring Exports feature can capture the values of the MAC address and VLAN ID fields from flows. The two supported VLAN types are 802.1q and the Cisco Inter-Switch Link (ISL) protocol.

Layer 2 MAC Address Fields

The Layer 2 fields for which the NetFlow Layer 2 and Security Monitoring Exports feature captures the values are as follows:

  • The source MAC address field from frames that are received by the NetFlow router.

  • The destination MAC address field from frames that are transmitted by the NetFlow router.

  • The VLAN ID field from frames that are received by the NetFlow router.

  • The VLAN ID field from frames that are transmitted by the NetFlow router.

Figure 2 shows the Ethernet Type II and Ethernet 802.3 frame formats. The destination address field and the source address field in the frame formats are the MAC address values that are captured by NetFlow.

Figure 4. Ethernet Type II and 802.3 Frame Formats

Table 1 explains the fields for the Ethernet frame formats.

Table 3 Ethernet Type II and 802.3 Frame Fields

Field

Description

Preamble

The entry in the Preamble field is an alternating pattern of 0s and 1s that communicates to receiving stations about an incoming frame. It also provides a means for the receiving stations to synchronize their clocks with the incoming bit stream.

SOF (Start of frame)

The SOF field holds an alternating pattern of 0s and 1s, ending with two consecutive 1s, indicating that the next bit is the first bit of the first byte of the destination MAC address.

Destination Address

The 48-bit destination address identifies which station on the LAN should receive the frame. The first two bits of the destination MAC address are reserved for the following special functions:

  • The first bit in the destination address field indicates whether the address is an individual address (0) or a group address (1).

  • The second bit indicates whether the destination address is globally administered (0) or locally administered (1).

The remaining 46 bits form a uniquely assigned value that identifies a single station, a defined group of stations, or all stations on the network.

Source Address

The 48-bit source address identifies which station transmitted the frame. The source address is always an individual address, and the leftmost bit in the Source Address field is always 0.

Type

or

Length

Type—In an Ethernet Type II frame, a part of the frame is used for the Type field. The Type field is used to identify the next layer protocol in the frame.

Length—In an 802.3 Ethernet frame, a part of the frame is used for the Length field. The Length field is used to indicate the length of the Ethernet frame. The value can be from 46 to 1500 bytes.

Data

or

802.2 header and data

Ethernet Type II—46 to 1500 bytes of data

or

802.3/802.2—8 bytes of header and 38 to 1492 bytes of data.

FCS (Frame Check Sequence)

This field contains a 32-bit cyclic redundancy check (CRC) value, which is created by the sending station and is recalculated by the receiving station, to check for damaged frames. The FCS is generated for the destination address, source address, Type, and Data fields of the frame. The FCS does not include the data portion of the frame.

Layer 2 VLAN ID Fields

NetFlow can capture the value in the VLAN ID field for 802.1q tagged VLANs and Cisco ISL encapsulated VLANs. This section describes the two types of VLANs, 802.1q and ISL.


Note


ISL and 802.1q are commonly called VLAN encapsulation protocols.


Understanding 802.1q VLANs

Devices that use 802.1q insert a four-byte tag into the original frame before it is transmitted. Figure 3 shows the format of an 802.1q tagged Ethernet frame.

Figure 5. 802.1q Tagged Ethernet Type II or 802.3 Frame

Table 2 describes the fields for 802.1q VLANs.

Table 4 802.1q VLAN Encapsulation Fields

Field

Description

Destination Address

The 48-bit destination address identifies which stations on the LAN should receive the frame. The first two bits of the destination MAC address are reserved for the following special functions:

  • The first bit in the destination address field indicates whether the address is an individual address (0) or a group address (1).

  • The second bit indicates whether the destination address is globally administered (0) or locally administered (1).

The remaining 46 bits form a uniquely assigned value that identifies a single station, a defined group of stations, or all stations on the network.

Source Address

The 48-bit source address identifies which station transmitted the frame. The source address is always an individual address, and the leftmost bit in the Source Address field is always 0.

Type

or

Length

Type—In an Ethernet Type II frame, a part of the frame is used for the Type field. The Type field is used to identify the next layer protocol in the frame.

Length—In an 802.3 Ethernet frame, a part of the frame is used for the Length field. The Length field is used to indicate the length of the Ethernet frame. The value can be from 46 to 1500 bytes.

Data

or

802.2 header and data

Ethernet Type II—46 to 1500 bytes of data

or

802.3/802.2—8 bytes of header and 38 to 1492 bytes of data.

FCS (Frame Check Sequence)

This field contains a 32-bit cyclic redundancy check (CRC) value, which is created by the sending station and is recalculated by the receiving station, to check for damaged frames. The FCS is generated for the destination address, source address, Type, and Data fields of the frame. The FCS does not include the data portion of the frame.

Tag Protocol ID (TPID)

This 16-bit field is set to a value of 0x8100 to identify the frame as an IEEE 802.1q tagged frame.

Priority

This 3-bit field refers to the 802.1p priority. It is also known as user priority. It indicates the frame priority level used for prioritizing traffic and can represent levels 0–7.

Tag Control Information

This 2-byte Tag Control Information field consists of the following two subfields:

  • Canonical Format Indentifier (CFI)—If the value of this 1-bit field is 1, the MAC address is in noncanonical format. If the value of this field is 0, the MAC address is in canonical format.

  • VLAN ID—This 12-bit field uniquely identifies the VLAN to which the frame belongs. It can have a value from 0 to 4095.

Cisco ISL VLANs

ISL is a Cisco-proprietary protocol for encapsulating frames on a VLAN trunk. Devices that use ISL add an ISL header to the frame. This process is known as VLAN encapsulation. 802.1Q is the IEEE standard for tagging frames on a VLAN trunk. Figure 4 shows the format of a Cisco ISL-encapsulated Ethernet frame.

Figure 6. Cisco ISL Tagged Ethernet Frame

Table 3 describes the fields for 802.1q VLANs.

Table 5 ISL VLAN Encapsulation

Field

Description

DA (destination address)

This 40-bit field is a multicast address and is set at 0n01-00-0c-00-00 or 0n03-00-0c-00-00. The receiving host determines that the frame is encapsulated in ISL by reading the 40-bit DA field and matching it with one of the two ISL multicast addresses.

TYPE

This 4-bit field indicates the type of frame that is encapsulated and to indicate alternative encapsulations.

TYPE codes:

  • 0000—Ethernet

  • 0001—Token Ring

  • 0010—FDDI

  • 0011—ATM

USER

This 4-bit field is used to extend the meaning of the Frame TYPE field. The default USER field value is 0000. For Ethernet frames, the USER field bits 0 and 1 indicate the priority of the packet as it passes through the switch. Whenever traffic can be handled more quickly, the packets with this bit set should take advantage of the quicker path. However, such paths are not required.

USER codes:

  • xx00—Normal priority

  • xx01—Priority 1

  • xx10—Priority 2

  • xx11—Highest priority

SA

This 48-bit field is the source address field of the ISL packet. It should be set to the 802.3 MAC address of the switch port transmitting the frame. The receiving device can ignore the SA field of the frame.

LEN

This 16-bit value field stores the actual packet size of the original packet. The LEN field represents the length of the packet in bytes, excluding the DA, TYPE, USER, SA, LEN, and FCS fields. The total length of the excluded fields is 18 bytes, so the LEN field represents the total length minus 18 bytes.

AAAA03(SNAP)

The AAAA03 Subnetwork Access Protocol (SNAP) field is a 24-bit constant value of 0xAAAA03.

HSA

This 24-bit field represents the upper three bytes (the manufacturer’s ID portion) of the SA field. It must contain the value 0x00-00-0C.

VLAN

This 15-bit field is the virtual LAN ID of the packet. This value is used to mark frames on different VLANs.

BPDU

The bit in the bridge protocol data unit (BPDU) field is set for all BPDU packets that are encapsulated by the ISL frame. The BPDUs are used by the spanning tree algorithm to learn information about the topology of the network. This bit is also set for Cisco Discovery Protocol and VLAN Trunk Protocol (VTP) frames that are encapsulated.

INDEX

This 16-bit field indicates the port index of the source of the packet as it exits the switch. It is used for diagnostic purposes only, and may be set to any value by other devices. It is ignored in received packets.

RES

This 16-bit field is used when Token Ring or FDDI packets are encapsulated with an ISL frame.

Encapsulated FRAME

This field contains the encapsulated Layer 2 frame.

FCS

The FCS field consists of 4 bytes. It includes a 32-bit CRC value, which is created by the sending station and is recalculated by the receiving station, to check for damaged frames. The FCS covers the DA, SA, Length/Type, and Data fields. When an ISL header is attached to a Layer 2 frame, a new FCS is calculated over the entire ISL packet and added to the end of the frame.

Note   

The addition of the new FCS does not alter the original FCS that is contained within the encapsulated frame.

NetFlow Top Talkers

The usual implementation of NetFlow exports NetFlow data to a collector. The NetFlow Top Talkers features can be used for security monitoring or accounting purposes for top talkers, and matching and identifying key traffic in your network. These features are also useful for a network location where a traditional NetFlow export operation is not possible. The NetFlow Top Talkers features do not require a collector to obtain information regarding flows. Instead, the NetFlow data is displayed on the router when the NetFlow Dynamic Top Talkers CLI show ip flow top command, or the NetFlow Top Talkers show ip flow top-talkersis used.

Comparison of the NetFlow Dynamic Top Talkers CLI and NetFlow Top Talkers Features

There are two very similar NetFlow features that can be used for monitoring the highest volume traffic in your network. The feature names are:

NetFlow Dynamic Top Talkers CLI

This feature was introduced in 12.4(4)T. The NetFlow Dynamic Top Talkers CLI feature is used to obtain an overview of the highest volume traffic (top talkers) in your network. It provides an overview of the traffic by aggregating the flows in the cache based on the aggregation field that you select when you use the NetFlow Dynamic Top Talkers CLI feature.

The NetFlow Dynamic Top Talkers CLI feature does not require modifications to the configuration of the router. The show ip flow top command is the only command that you need to use for the NetFlow Dynamic Top Talkers CLI feature. You can invoke any of the NetFlow Dynamic Top Talkers CLI options directly from the show ip flow top command whenever you need them.


Note


The information that you want to use the NetFlow Dynamic Top Talkers CLI feature to analyze must be available in the cache. For example, if you want to be able to identify the MAC address in the flows, you must configure the ip flow-capture mac-addresses command in order to capture the values from the MAC address fields in the traffic first.


The NetFlow Dynamic Top Talkers CLI feature aggregates flows and allows them to be sorted so that they can be viewed. The flows can be aggregated on fields in the cache such as source or destination IP address, ICMP type and code values, and so forth. For a full list of the fields that you can aggregate the flows on, refer to the show ip flow topcommand in the Cisco IOS NetFlow command reference documentation.

The aggregated top talker flows can be sorted by any of the following criteria:

  • The aggregated field in the display data

  • The number of bytes in the display data

  • The number of flows in the display data

  • The by number of packets in the display data

  • In ascending or descending order (to find the least used Top talker)

In addition to sorting top talkers, you can further organize your output by specifying criteria that the top talkers must match, such as source or destination IP address or port. The match keyword is used to specify this criterion. For a full list of the matching criterion that you can select, refer to the show ip flow topcommand in the Cisco IOS NetFlow command reference documentation.

The NetFlow Dynamic Top Talkers CLI feature can help you quickly identify traffic that is associated with security threats such as DoS attacks because it does not require configuration modifications. You can change the NetFlow Dynamic Top Talkers CLI options for identifying and analyzing network threats in the aggregated flows on-the-fly as you learn more about the traffic that is of interest. For example, after you have identified that there is a lot of ICMP traffic in your network by using the show ip flow top 10 aggregate icmp command you can learn what IP networks the traffic is being sent to by using the show ip flow top 10 aggregate icmp match destination-prefix 172.0.0.0/8 command.


Note


A high volume of ICMP traffic might indicate that an ICMP-based DoS attack is in progress.


The show ip flow top command:

  • Does not require additional NetFlow configuration commands to display top talkers. Therefore you do not need to supply the configuration mode password to the administrators who use the he show ip flow top command to monitor network traffic. The only prerequisite for using the show ip flow top command is that you have configured NetFlow on at least one interface on the router.

  • Aggregates flows automatically based on the aggregation method that you select, and independently of any netflow aggregation cache(s).

  • Allows you to change the parameters of the command, such as the number of flows to display, the display order, and match criterion, on-the-fly every time that you use the command without having to change the router’s configuration.

  • Allows you to sort the display output in ascending or descending order based on:
    • The aggregated field
    • The number of bytes
    • The number of flows,
    • The number of packets
show ip flow top and show ip cache verbose flow

Many of the values shown in the display output of the show ip cache verbose flow command are in hexadecimal. If you want to match these values using the show ip flow top command with the match keyword, you must enter the field value that you want to match in hexadecimal. For example, to match on the destination port of 00DC in the following except from the show ip cache verbose flow command, you would use the match destination-port 0x00DC keywords and argument for the show ip flow top command.

SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs  Pkts
Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
Et0/0.1        10.10.11.4      Et1/0.1        172.16.10.8     06 00  00     209 
00DC /0  0                     00DC
 /0  0     0.0.0.0                40   281.4
MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
Min plen:       40                            Max plen:        40
Min TTL:        59                            Max TTL:         59
IP id:           0
Match Criteria with the show ip flow top command

You can limit the top talkers that are displayed by the show ip flow top command by using the match keyword and arguments. For example, you can display the IP destination address top talkers that have a prefix of 224.0.0.0 using the show ip flow top 10 aggregate destination-address match destination-prefix 224.0.0.0/3 command.

For a full list of the matching criterion that you can select, refer to the show ip flow topcommand in the Cisco IOS NetFlow Command Reference . If you do not configure match criteria all of the flows are considered as candidates for aggregation as top talkers based on the volume of traffic they represent.

The Order That Aggregation Occurs in

With the exception of the flows keyword, all matches are performed prior to aggregation, and only matching flows are aggregated. For example, the show ip flow top5aggregate destination-address match destination-prefix 172.16.0.0/16 command analyzes all of the available flows looking for any flows that have destination addresses that match the destination-prefix value of 172.16.0.0/16. If it finds any matches it aggregates them, and then displays the number of aggregated destination-address flows that is equal to the number of top talkers that were requested in the command-in this case five.

The flows keyword matches the number of aggregated flows post-aggregation. For example, the show ip flow top 2 aggregate destination-address match 6 command aggregates all of the flows on the values in their destination IP address field, and then displays the top talkers that have 6 aggregated flows.

Number of Flows Matched

If you do not specify match criteria and there is traffic in the flows that includes the field that you used to aggregate the flows on, all of the flows will match. For example, if your router has 20 flows with IP traffic and you enter the show ip flow top 10 aggregate destination-address command the display will indicate that 20 of 20 flows matched, and the 10 top talkers will be displayed.

If you use the match keyword to limit the flows that are aggregated to the flows with a destination prefix of 224.0.0.0/3, and only one flow matches this criterion the output will indicate that one out of six flows matched. For example, if your router has 6 flows with IP traffic, but only one of them has a destination prefix of 224.0.0.0/3, and you enter the show ip flow top 10 aggregate destination-address match destination-prefix 224.0.0.0/3 command, the display will indicate that 1 of 6 flows matched.

If the total number of top talkers is less than the number of top talkers that were requested in the command, the total number of top talkers is displayed. For example, if you enter a value of five for the number of top talkers to display and there are only three top talkers that match the criteria that you used, the display will only include three top talkers.

When a match criterion is included with the show ip flow top command, the display output will indicate "N of M flows matched" where N <= M, N = matched flows, and M = total flows seen. The numbers of flows seen could potentially be more than the total number of flows in the cache if some of the analyzed flows were removed from the cache and new flows were created ahead of the current point, as the top talkers feature sweeps through the cache. Therefore, M is NOT the total number of flows in the cache, but rather, the number of observed flows.

If you attempt to display the top talkers by aggregating them on a field that is not in the cache you will see the "% aggregation-field" is not available for this cache" message. For example, if you use the show ip flow top 5 aggregate s ource-vlan command, and you have not enabled the capture of VLAN IDs from the flows, you will see the "% VLAN id is not available for this cache" message.

NetFlow Top Talkers

This feature was introduced in 12.3(11)T. NetFlow Top Talkers is used to obtain information about individual flows in the cache. It does not aggregate the flows like the NetFlow Dynamic Top Talkers CLI feature.

The NetFlow Top Talkers feature compares all of the flows and displays information about each of the flows that have the heaviest traffic volumes (top talkers). The show ip flow top-talkerscommand requires you to pre-configure the router using the NetFlow Top Talkers configuration commands:

  • ip flow-top-talkers --Enters the NetFlow Top Talkers configuration mode.

  • sort-by --Selects the sort order for the flows in the display output.
    • bytes--Sort the flows based on the numbers of bytes in each flow.
    • packets--Sort the flows based on the numbers of packets in each flow.
  • top --Specifies the number of top talkers to monitor.

  • match (optional)--Specifies additional criteria, such as IP addresses, port numbers, and so forth, that must be matched in the flow to qualify as a candidate for top talker status.

For a full list of the matching criterion that you can select, refer to the ip flow top-talkerscommand in the Cisco IOS NetFlow Command Reference . If you do not configure match criteria all of the flows are considered as candidates as top talkers based on the volume of traffic they represent.

  • show ip flow top talkers [verbose]--Displays the flows.

For more information on the NetFlow Top Talkers feature, refer to Configuring NetFlow Top Talkers using Cisco IOS CLI Commands or SNMP Commands.

Filtering and Sampling of NetFlow Traffic

NetFlow provides highly granular per-flow traffic statistics in a Cisco router. A flow is a unidirectional stream of packets that arrive at the router on the same subinterface, have the same source and destination IP addresses, Layer 4 protocol, TCP/UDP source and destination ports, and the same ToS (type of service) byte in the IP headers. The router accumulates NetFlow statistics in a NetFlow cache and can export them to an external device (such as the Cisco Networking Services (CNS) NetFlow Collection Engine) for further processing.

Full NetFlow accounts for all traffic entering the subinterface on which it is enabled. But in some cases, you might gather NetFlow data on only a subset of this traffic. The Random Sampled NetFlow feature and the NetFlow Input Filters feature each provide ways to limit incoming traffic to only traffic of interest for NetFlow processing. Random Sampled NetFlow provides NetFlow data for a subset of traffic in a Cisco router by processing only one randomly selected packet out of n sequential packets. The NetFlow Input Filters feature provides the capability to gather NetFlow data on only a specific user-defined subset of traffic.


Note


Random Sampled NetFlow is more statistically accurate than Sampled NetFlow. NetFlow's ability to sample packets was first provided by a feature named Sampled NetFlow. The methodology that the Sampled NetFlow feature uses is deterministic sampling, which selects every nth packet for NetFlow processing on a per-interface basis. For example, if you set the sampling rate to 1 out of 100 packets, then Sampled NetFlow samples the 1st, 101st, 201st, 301st, and so on packets. Sampled NetFlow does not allow random sampling and thus can make statistics inaccurate when traffic arrives in fixed patterns.



Note


The Random Sampled NetFlow algorithms are applied after input filtering.


The table below compares the NetFlow Input Filters feature and the NetFlow Random Sampled feature.

Table 6 Comparison of the NetFlow Input Filters Feature and the Random Sampled NetFlow Feature

Comparison Category

NetFlow Input Filters Feature

Random Sampled NetFlow Feature

Brief description

This feature enables you to gather NetFlow data on only a specific subset of traffic. You do this by creating filters to select flows for NetFlow processing. For example, you can select flows from a specific group of hosts. This feature also lets you select various sampling rates for selected flows.

This feature provides NetFlow data for a subset of traffic in a Cisco router by processing only one randomly selected packet out of n sequential packets (n is a user-configurable parameter). Packets are sampled as they arrive (before any NetFlow cache entries are made for those packets).

Main uses

You can use this feature for class-based traffic analysis and monitoring on-network or off-network traffic.

This feature is also useful if you have too much traffic and you want to limit the traffic that is analyzed.

You can use this feature for traffic engineering, capacity planning, and applications where full NetFlow is not needed for an accurate view of network traffic.

This feature is also useful if you have too much traffic and you want to limit the traffic that is analyzed.

Export format support

This feature is supported in the Version 5 and Version 9 NetFlow export formats.

This feature is supported in the Version 5 and Version 9 NetFlow export formats.

Cisco IOS release support

12.3(4)T.

12.3(2)T, 12.2(18)S, and 12.0(26)S.

Subinterface support

You can configure NetFlow Input Filters per subinterface as well as per physical interface.

You can select more than one filter per subinterface and have all of the filters run simultaneously.

You can configure the Random Sampled NetFlow feature per subinterface as well as per physical interface.

You can not run Full NetFlow and Random Sampled NetFlow concurrently on the same subinterface. You must disable full NetFlow on the subinterface before Random Sampled NetFlow will take effect.

Traffic is collected only on the subinterfaces on which Random Sampled NetFlow is configured. As with full NetFlow, enabling Random Sampled NetFlow on a physical interface does not enable Random Sampled NetFlow on subinterfaces automatically--you must explicitly configure it on the subinterfaces.

Memory impact

This feature requires no additional memory. It allows you to use a smaller NetFlow cache than full NetFlow, because it significantly reduces the number of flows. This feature requires an insignificant amount of memory for each configured NetFlow filter.

This feature can create a smaller NetFlow cache than full NetFlow if by reducing the number of packets being analyzed the numbers of flows in the cache is also reduced. This feature requires an insignificant amount of memory for each configured NetFlow sampler.

Performance impact

Accounting of classified traffic saves router resources by reducing the number of flows being processed and exported. The amount of bandwidth saved depends on the usage and the class-map criteria.

However, performance might degrade depending on the number and complexity of class maps configured in a policy.

Statistical traffic sampling substantially reduces consumption of router resources (especially CPU resources) while providing valuable NetFlow data.

This feature substantially reduces the impact of NetFlow data export on interface traffic. For example, a sampling rate of 1 out of 100 packets reduces the export of NetFlow data by about 99% percent.

NetFlow Input Filters Flow Classification

For the NetFlow Input Filters feature, classification of packets can be based on any of the following: IP source and destination addresses, Layer 4 protocol and port numbers, incoming interface, MAC address, IP Precedence, DSCP value, Layer 2 information (such as Frame-Relay DE bits or Ethernet 802.1p bits), and Network-Based Application Recognition (NBAR) information. The packets are classified (filtered) on the above criteria, and flow accounting is applied to them on subinterfaces.

The filtering mechanism uses the Modular QoS Command-Line Interface (MQC) to classify flows. You can create multiple filters with matching samplers on a per-subinterface basis. For example, you can subdivide subinterface traffic into multiple classes based on type of service (ToS) values or destination prefixes (or both). For each class, you can also configure sampling at a different rate, using higher rates for higher-priority classes of traffic and lower rates for lower-priority ones.

MQC has many policies (actions) such as bandwidth rate and queuing management. These policies are applied only if a packet matches a criterion in a class map that is applied to the subinterface. A class map contains a set of match clauses and instructions on how to evaluate the clauses and acts as a filter for the policies, which are applied only if a packet’s content satisfies the match clause. The NetFlow Input Filters feature adds NetFlow accounting to the MQC infrastructure, which means that flow accounting is done on a packet only if it satisfies the match clauses.

Two types of filter are available:

  • ACL-based flow-mask filters

  • Fields of filter (source IP address, destination IP address, source application port, destination application port, port protocol, ToS bits, and TCP flags)

For more information on Modular QoS Command-Line Interface (MQC) refer to the Cisco IOS Quality of Service Solutions Configuration Guide .

Random Sampled NetFlow Sampling Mode

Sampling mode makes use of an algorithm that selects a subset of traffic for NetFlow processing. In the random sampling mode that the Random Sampled NetFlow feature uses, incoming packets are randomly selected on average one out of each n sequential packets is selected for NetFlow processing. For example, if you set the sampling rate to 1 out of 100 packets, then NetFlow might sample the 5th packet and then the 120th, 230th, 302nd, and so on. This sample configuration provides NetFlow data on 1 percent of total traffic. The n value is a parameter that you can configure from 1 to 65535 packets.

Random Sampled NetFlow The NetFlow Sampler Map

Random Sampled NetFlow is useful if you have too much traffic and you want to limit the traffic that is analyzed. A NetFlow sampler map is created with the flow-sampler-map sampler-map-name command. The sampling mode for the sampler map is configured with the mode random one-out-of sampling-rate command. The range of values for the sampling-rate argument is 1 to 65535. Each NetFlow sampler map can be applied to one or many subinterfaces as well as physical interfaces. The sampler map is applied to an interface or subinterface with the flow-sampler sampler-map-name command. You can define up to eight NetFlow sampler maps.

How to Configure and Use NetFlow to Detect and Analyze Network Threats

Using NetFlow to detect and analyze network threats requires a combination of configuration commands and show commands. You start by configuring the NetFlow Layer 2 and Security Monitoring Exports feature to capture values of the additional non-key fields from the flows so that they can be displayed in the cache by the NetFlow show commands. Capturing the values in the additional non-key fields is required so that you can identify the path the traffic is taking through the network and other characteristics of the traffic such as TTL values and packet length values.

After you configure the NetFlow Layer 2 and Security Monitoring Exports feature, you use the NetFlow Dynamic Top Talkers CLI command to obtain an overview of the traffic flows the router is forwarding. The overview displays information such as the protocol distribution in the flows, the source ip addresses that are sending the flows, and the networks the flows are being sent to.

After you identify the type of flows that you want to focus, on such as ICMP traffic, and other characteristics such as source IP addresses and destination network prefixes, you use the NetFlow Top Talkers feature to obtain more focused and detailed information on the individual flows. The NetFlow Top Talkers feature is configured with match criteria that focuses it on the types of traffic that you have identified. If your router is keeping track of several flows and you are only interested in analyzing a subset of them you, can configure NetFlow Input Filters to limit the flows that NetFlow is tracking.

Prerequisites

CEF or dCEF must be configured globally, and on the interface that you want to run NetFlow on, before you configure NetFlow Layer 2 and Security Monitoring Exports.

You must have NetFlow enabled on at least one interface in the router before you configure NetFlow Layer 2 and Security Monitoring Exports.

If you want to capture the values of the Layer 3 IP fragment offset field from the IP headers in your IP traffic using the ip flow-capture fragment-offset command, your router must be running Cisco IOS 12.4(2)T or later.

This section contains the following procedures:

Configuring NetFlow Layer 2 and Security Monitoring Exports

Perform the following task to configure the NetFlow Layer 2 and Security Monitoring Exports feature.

Before You Begin

To export the data captured with the NetFlow Layer 2 and Security Monitoring feature, you must configure NetFlow to use the NetFlow Version 9 data export format.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    ip flow-capture fragment-offset

    4.    ip flow-capture icmp

    5.    ip flow-capture ip-id

    6.    ip flow-capture mac-addresses

    7.    ip flow-capture packet-length

    8.    ip flow-capture ttl

    9.    ip flow-capture vlan-id

    10.    interface type interface-type interface-number ]

    11.    ip flow ingress

    12.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 ip flow-capture fragment-offset


    Example:
    Router(config)# ip flow-capture fragment-offset
     

    Enables capturing the value of the IP fragment offset field from the first fragmented IP datagram in a flow.

     
    Step 4 ip flow-capture icmp


    Example:
    Router(config)# ip flow-capture icmp
     

    Enables you to capture the value of the ICMP type and code fields from the first ICMP datagram in a flow.

     
    Step 5 ip flow-capture ip-id


    Example:
    Router(config)# ip flow-capture ip-id
     

    Enables you to capture the value of the IP-ID field from the first IP datagram in a flow.

     
    Step 6 ip flow-capture mac-addresses


    Example:
    Router(config)# ip flow-capture mac-addresses
     

    Enables you to capture the values of the source and destination MAC addresses from the first Layer 2 frame in a flow.

     
    Step 7 ip flow-capture packet-length

    Example:
    Router(config)# ip flow-capture packet-length
     

    Enables you to capture the minimum and maximum values of the packet length field from IP datagrams in a flow.

     
    Step 8 ip flow-capture ttl


    Example:
    Router(config)# ip flow-capture ttl
     

    Enables you to capture the minimum and maximum values of the Time-to-Live (TTL) field from IP datagrams in a flow.

     
    Step 9 ip flow-capture vlan-id


    Example:
    Router(config)# ip flow-capture vlan-id
     

    Enables you to capture the 802.1q or ISL VLAN-ID field from first VLAN encapsulated Layer 2 frame in a flow that is received or transmitted on a trunk port.

     
    Step 10 interface type interface-type interface-number ]


    Example:
    Router(config)# interface ethernet 0/0
     

    Enters interface configuration mode for the type of interface specified in the command.

     
    Step 11 ip flow ingress


    Example:
    and/or


    Example:
    ip flow egress


    Example:
    Router(config-if)# ip flow ingress


    Example:
    and/or


    Example:
    Router(config-if)# ip flow egress
     

    Enables ingress NetFlow data collection on the interface.

    and/or

    Enables egress NetFlow data collection on the interface.

     
    Step 12 end

    Example:
    Router(config)# end
     

    Returns to privileged EXEC mode.

     

    Verifying NetFlow Layer 2 and Security Monitoring Exports

    This task verifies that NetFlow Layer 2 and Security Monitoring Exports is configured correctly. The show ip cache verbose flowcommand gives a detailed view of the status and statistics for flows in the NetFlow main cache. The values for the NetFlow non-key fields that you have configured with the NetFlow Layer 2 and Security Monitoring Exports feature are included for each flow.

    To see the values of the fields that you have configured the NetFlow Layer 2 and Security Monitoring Exports feature to capture, your router must be forwarding IP traffic that meets the criteria for these fields. For example, if you configure the ip flow-capture vlan-id command, your router must be forwarding IP datagrams over interfaces that are configured as VLAN trunks to capture the VLAN-ID values from the layer-two frames carrying the IP datagrams in the flow.

    Restrictions

    Displaying Detailed NetFlow Cache Information on Platforms Running Distributed Cisco Express Forwarding

    On platforms running dCEF, NetFlow cache information is maintained on each line card or Versatile Interface Processor. If you want to use the show ip cache verbose flow command to display this information on a distributed platform, you must enter the command at a line card prompt.

    Cisco 7500 Series Platform

    To display detailed NetFlow cache information on a Cisco 7500 series router that is running distributed dCEF, enter the following sequence of commands:

    Router# if-con
     
    slot-number
    LC-
    slot-number
    # show ip cache verbose
     flow
    

    For Cisco IOS Releases 12.3(4)T, 12.3(6), and 12.2(20)S and later, enter the following command to display detailed NetFlow cache information:

    Router# execute-on 
    slot-number 
    show ip cache verbose
     flow
     

    Cisco 12000 Series Platform

    To display detailed NetFlow cache information on a Cisco 12000 Series Internet Router, enter the following sequence of commands:

    Router# attach
     
    slot-number
    LC-
    slot-number
    # show ip cache verbose
     flow
    

    For Cisco IOS Releases 12.3(4)T, 12.3(6), and 12.2(20)S and later, enter the following command to display detailed NetFlow cache information:

    Router# execute-on slot-number show ip cache verbose flow

    To verify the configuration of NetFlow Layer 2 and Security Monitoring Exports use the following step.

    SUMMARY STEPS

      1.    show ip cache verbose flow


    DETAILED STEPS
    show ip cache verbose flow

    This example shows that NetFlow Layer 2 and Security Monitoring Exports is working properly because the values have been captured from the non-key Layer 3 and Layer 2 fields in the flows. The values captured in the flows are shown in bold text.



    Example:
    Router# show ip cache verbose flow
    IP packet size distribution (33978 total packets):
    1-32   64   96  128  160  192  224  256  288  320  352  384  416  448  480
    .856 .143 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
    512  544  576 1024 1536 2048 2560 3072 3584 4096 4608
    .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
    IP Flow Switching Cache, 278544 bytes
    14 active, 4082 inactive, 59 added
    12452 ager polls, 0 flow alloc failures
    Active flows timeout in 10 minutes
    Inactive flows timeout in 15 seconds
    IP Sub Flow Cache, 25736 bytes
    28 active, 996 inactive, 148 added, 59 added to flow
    0 alloc failures, 0 force free
    1 chunk, 1 chunk added
    last clearing of statistics never
    Protocol         Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)
    --------         Flows     /Sec     /Flow  /Pkt     /Sec     /Flow     /Flow
    TCP-SMTP             2      0.0      1730    40      3.6     600.7       0.2
    UDP-other           31      0.0         1    54      0.0       3.6      16.8
    ICMP                12      0.0      1728    28     22.0     600.1       0.1
    Total:              45      0.0       538    29     25.7     189.2      11.6
    SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs  Pkts
    Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
    .
    .
    .
    Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  10     696
    0000 /0  0                     0C01 /0  0     0.0.0.0                28   241.4
    MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
    Min plen:       28                            Max plen:        28
    Min TTL:        59                            Max TTL:         59
    ICMP type:      12                            ICMP code:        1
    IP id:           0
    

    Using NetFlow Dynamic Top Talkers CLI to Display the Protocol Distribution

    You can obtain a quick overview of the traffic in your network by viewing the protocol distribution. Use this task to display the top talkers (aggregated flows) for these three IPv4 protocol types:

    • 1--ICMP

    • 6--TCP

    • 17--UDP

    SUMMARY STEPS

      1.    show ip flow top number aggregate aggregate-field sorted-by packets descending


    DETAILED STEPS
    show ip flow top number aggregate aggregate-field sorted-by packets descending

    The following example looks for up to three top talkers, aggregates them on the protocol field, sorts them by packets, and displays the output in descending order:



    Example:
    Router# show ip flow top 3 aggregate protocol sorted-by packets descending
     
    There are 3 top talkers:
    IPV4 PROT       bytes        pkts       flows
    =========  ==========  ==========  ==========
            1      406196       14507          12
            6       96560        2414           2
           17          52           1           1
    15 of 15 flows matched.
    

    The table below describes the significant fields shown in the display output.

    Table 7 show ip flow top 3 aggregate protocol sorted-by packets descending Field Descriptions

    Field

    Description

    There are 3 top talkers

    The number of top talkers is displayed.

    IPV4 PROT

    This position in the display output is used to show the field that you selected to aggregate the flows on.

    The protocol keyword aggregates IPv4 traffic in the flows based on the IPv4 protocol type. In this example there are three IPv4 protocol types in the flows:

    • 1--ICMP

    • 6--TCP

    • 17--UDP

    bytes

    Displays the numbers of bytes in the aggregated flows for each top talker.

    pkts

    Displays the numbers of packets in the aggregated flows for each top talker.

    flows

    Displays the numbers of aggregated flows for each top talker.

    15 of 15 flows matched.

    Displays the number of flows that matched the command.

    All 15 flows in the router are aggregated into three top talkers. In this example all of the flow traffic is top talker traffic.

    The majority of the traffic is ICMP traffic (IP protocol type 1). This might indicate an ICMP DoS attack is in progress.


    Using NetFlow Dynamic Top Talkers CLI to Display the Source IP Address Top Talkers Sending ICMP Traffic

    The display output from the show ip flow top 10 aggregate protocol sorted-by packets descending used in Using NetFlow Dynamic Top Talkers CLI to Display the Protocol Distribution section indicates that there is a possible ICMP-based DoS attack in progress. The next step to take is to identify the flows that are sending the ICMP traffic. In this case the flows will be aggregated on the source IP addresses.

    SUMMARY STEPS

      1.    show ip flow top number aggregate aggregate-field sorted-by packets match match-field match-value


    DETAILED STEPS
    show ip flow top number aggregate aggregate-field sorted-by packets match match-field match-value

    The following command looks for up to 20 top talkers, aggregates them on the source IP address, sorts them by packets, and matches on the protocol icmp:



    Example:
    Router# show ip flow top 20 aggregate source-address sorted-by packets match protocol icmp
    There are 6 top talkers:
    IPV4 SRC-ADDR         bytes        pkts       flows
    ===============  ==========  ==========  ==========
    10.132.221.111        90440        3230           1
    10.10.12.1            90440        3230           1
    10.251.138.218        90440        3230           1
    10.71.200.138         90384        3228           1
    10.231.185.254        90384        3228           1
    10.106.1.1            90356        3227           1
    6 of 15 flows matched.
    Router
    

    The table below describes the significant fields shown in the display.

    Table 8 show ip flow top 20 aggregate source-address sorted-by packets match protocol icmp Field Descriptions

    Field

    Description

    There are 6 top talkers

    The number of top talkers is displayed.

    Note   

    Only 6 top talkers are displayed, even though you asked for 20, because only 6 of the 15 flows in the cache matched the criteria you specified. The number 20 is an upper limit that will be applied in the event that there are over 20 top talkers.

    IPV4 SRC-ADDR

    This position in the display output is used to show the field that you selected to aggregate the flows on.

    The source-addresskeyword aggregates flows based on the source IP address. In this example there are 6 IP source addresses with aggregated flows. Each of the IP addresses has 1 flow, therefore no aggregation was performed:

    • 10.132.221.111

    • 10.10.12.1

    • 10.251.138.218

    • 10.71.200.138

    • 10.231.185.254

    • 10.106.1.1

    bytes

    Displays the numbers of bytes in the aggregated flows for each top talker.

    pkts

    Displays the numbers of packets in the aggregated flows for each top talker.

    flows

    Displays the numbers of aggregated flows for each top talker.

    6 of 15flows matched.

    Displays the number of flows that matched the command.

    The ICMP traffic is aggregated into six top talkers (source IP addresses). Each top talker has one flow. No aggregation is performed on this traffic because there is a 1-to-1 correlation of IP source addresses and flows.


    Using NetFlow Dynamic Top Talkers CLI to Display the Destination IP Address Top Talkers Receiving ICMP Traffic

    The display output from the show ip flow top 5 aggregate source-address sorted-by packets match protocol icmp command used in Using NetFlow Dynamic Top Talkers CLI to Display the Source IP Address Top Talkers Sending ICMP Traffic section showed the six top talkers (IP source addresses) that are sending the 12 ICMP traffic flows. The next step to take is to identify the flows that are the target of the ICMP traffic. In this case the flows will be aggregated on the destination IP addresses.

    SUMMARY STEPS

      1.    show ip flow top number aggregate aggregate-field sorted-by packets match match-field match-value


    DETAILED STEPS
    show ip flow top number aggregate aggregate-field sorted-by packets match match-field match-value

    The following command looks for up to 20 top talkers, aggregates them on the destination IP address, sorts them by packets, and matches on the protocol icmp



    Example:
    Router# show ip flow top 20 aggregate destination-address sorted-by packets match protocol icmp
    There is 1 top talker:
    IPV4 DST-ADDR         bytes        pkts       flows
    ===============  ==========  ==========  ==========
    172.16.10.2          407456       14552           6
    6 of 14 flows matched.
    Router
    

    The table below describes the significant fields shown in the display.

    Table 9 show ip flow top 20 aggregate destination-address sorted-by packets match protocol icmp Field Descriptions

    Field

    Description

    There is 1 top talker

    The number of top talkers is displayed.

    • The ICMP traffic is aggregated into 6 flows for one destination IP addresses.

    IPV4 DST-ADDR

    This position in the display output is used to show the field that you selected to aggregate the flows on.

    The destination-addresskeyword aggregates flows based on the destination IP address. In this example there are 3 IP destination address with aggregated flows. The IP addresses has 8 aggregated flows:

    • 172.16.10.2

    bytes

    Displays the numbers of bytes in the aggregated flows for each top talker.

    pkts

    Displays the numbers of packets in the aggregated flows for each top talker.

    flows

    Displays the numbers of aggregated flows for each top talker.

    6 of 14 flows matched.

    Displays the number of flows that matched the command.

    The previous task identified six ICMP top talkers based on source IP addresses that each had one flow. This task identified that there is one ICMP top talker based on destination IP addresses that is the target for 6 individual flows. There is a 1-to-1 correlation between the number of ICMP flows in the top talkers aggregated on the source IP address and the number of ICMP flows in the top talkers aggregated on the destination IP address. There is a high probability that an ICMP-based DoS attack on the host with the IP address of 172.16.10.2 is in progress.


    Configuring NetFlow Top Talkers to Monitor Network Threats

    The previous task (Using NetFlow Dynamic Top Talkers CLI to Display the Destination IP Address Top Talkers Receiving ICMP Traffic) identified a probable ICMP-based DoS attack on the host with the IP address 172.16.10.2. This task uses the NetFlow Top Talkers feature to configure the router to monitor the DoS attack by tracking the individual ICMP flows. After you have configured the NetFlow Top Talkers feature to focus on the DoS attack traffic, you can use the show ip flow top-talkers verbose command to identify the path the DoS traffic is taking through the network.

    Perform the following task to configure the NetFlow Top Talkers feature.

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    ip flow-top-talkers

      4.    match destination address ip-address /prefix-mask

      5.    top number

      6.    sort-by [bytes | packets

      7.    end


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Router> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Router# configure terminal
       

      Enters global configuration mode.

       
      Step 3 ip flow-top-talkers


      Example:
      Router(config)# ip flow-top-talkers
      
       

      Enters NetFlow top talkers configuration mode.

       
      Step 4 match destination address ip-address /prefix-mask


      Example:
      Router(config-flow-top-talkers)
      # match destination address 172.16.10.2/32
      
       

      Specifies the destination IP addresses to match.

       
      Step 5 top number


      Example:
      Router(config-flow-top-talkers)# top 50
       

      Specifies the maximum number of top talkers that will be retrieved by a NetFlow top talkers query.

       
      Step 6 sort-by [bytes | packets


      Example:
      Router(config-flow-top-talkers)# sort-by packets
       

      Specifies the sort criterion for the top talkers.

      • The top talkers can be sorted either by the total number of packets of each top talker or the total number of bytes of each top talker.

       
      Step 7 end


      Example:
      Router(config-flow-top-talkers)# end
       

      Exits to privileged EXEC mode.

       

      Monitoring and Analyzing the NetFlow Top Talkers Flows

      To monitor and analyze the NetFlow Top Talkers flows, use the following step.

      SUMMARY STEPS

        1.    show ip flow top-talkers verbose


      DETAILED STEPS
      show ip flow top-talkers verbose

      The following sample shows details for the six traffic flows that are being sent to the host with IP address 172.16.10.2.



      Example:
      Router# show ip flow top-talkers verbose
      SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs Bytes
      Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
      Et0/0.1        10.106.1.1      Et1/0.1        172.16.10.2     01 00  10    9408 
      0000 /0  0                     0800 /0  0     0.0.0.0                28   116.3
      MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
      Min plen:       28                            Max plen:        28
      Min TTL:        59                            Max TTL:         59
      ICMP type:       8                            ICMP code:        0
      IP id:           0
      Et0/0.1        10.132.221.111  Et1/0.1        172.16.10.2     01 00  10    9408 
      0000 /0  0                     0800 /0  0     0.0.0.0                28   116.4
      MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
      Min plen:       28                            Max plen:        28
      Min TTL:        59                            Max TTL:         59
      ICMP type:       8                            ICMP code:        0
      IP id:           0
      Et0/0.1        10.10.12.1      Et1/0.1        172.16.10.2     01 00  10    9408 
      0000 /0  0                     0C01 /0  0     0.0.0.0                28   116.4
      MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
      Min plen:       28                            Max plen:        28
      Min TTL:        59                            Max TTL:         59
      ICMP type:      12                            ICMP code:        1
      IP id:           0
      Et0/0.1        10.251.138.218  Et1/0.1        172.16.10.2     01 00  10    9408 
      0000 /0  0                     0C01 /0  0     0.0.0.0                28   116.4
      MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
      Min plen:       28                            Max plen:        28
      Min TTL:        59                            Max TTL:         59
      ICMP type:      12                            ICMP code:        1
      IP id:           0
      Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  10    9408 
      0000 /0  0                     0C01 /0  0     0.0.0.0                28   116.5
      MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
      Min plen:       28                            Max plen:        28
      Min TTL:        59                            Max TTL:         59
      ICMP type:      12                            ICMP code:        1
      IP id:           0
      Et0/0.1        10.231.185.254  Et1/0.1        172.16.10.2     01 00  10    9408 
      0000 /0  0                     0C01 /0  0     0.0.0.0                28   116.5
      MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
      Min plen:       28                            Max plen:        28
      Min TTL:        59                            Max TTL:         59
      ICMP type:      12                            ICMP code:        1
      IP id:           0
      6 of 50 top talkers shown. 6 of 8 flows matched.
      
      Note   

      Only six of the eight flows matched because the rest of the flows are not top talker flows.

      Note   

      The top 50 flows were requested, however there are only eight flows in the cache.

      This display output contains the information required for determining the path that the DoS attack traffic is taking through the network. This information will be used to react to the DoS attack by adding security measures such as access-lists to the affected interfaces. The table below describes the significant fields in the display from the show ip flow top-talkers verbose command for determining the network path the DoS traffic is taking.
      Table 10 Significant Field Descriptions for show ip flow top-talkers verbose

      Field

      Description

      SrcIf

      Interface on which the packet was received.

      • All of the ICMP DoS traffic is being received on Et0/0.1

      SrcIPaddress

      This is the source IP address of the traffic in the six top talkers. The traffic is using 6 different IP source addresses

      • 10.132.221.111

      • 10.10.12.1

      • 10.251.138.218

      • 10.71.200.138

      • 10.231.185.254

      • 10.106.1.1

      DstIf

      Interface from which the packet was transmitted.

      • All of the ICMP DoS traffic is being transmitted over Et1/0.1

      Note   

      If an asterisk (*) immediately follows the DstIf field, the flow being shown is an egress flow.

      ICMP Type

      The ICMP datagram types

      • 8--Echo

      • 12--Parameter Problem

      ICMP Code

      The ICMP codes

      • 0--None (not applicable)

      • 1--Depends on the ICMP Type
        • A code value of 1 for ICMP type 12 indicates that a required option is missing

      DstIPaddress

      This is the destination IP address of the traffic.

      Note   

      172.17.10.2 is the IP address that is being attacked.

      MAC

      These are the source and destination MAC addresses from the traffic. The source and destination MAC address are read from left to right in the output.

      • The traffic is being received from MAC address aaa.bbb.cc03.

      Note   

      This MAC address is interface 1/0.1 on router R2.

      • The traffic is being transmitted to MAC address aaa.bbb.cc06.

      Note   

      This MAC address is interface 1/0.1 on router R4.

      VLAN id

      These are the source and destination VLAN IDs. The source and destination VLAN IDs are read from left to right in the output.

      • The traffic is being received from VLAN 5.

      • The traffic is being transmitted to VLAN 6.

      The flows in this example show only the ICMP DoS attack traffic that is destined for the host with IP address 172.16.10.2. These flows were created specifically for documenting this task. In a real network, the host under attack might be communicating with other hosts that are using legitimate applications such as e-mail and web sites. In this case, the Top Talkers match filter on the destination IP address (match destination address 172.16.10.2/32) that was configured in the Configuring NetFlow Top Talkers to Monitor Network Threats will not limit the display of the show ip flow top-talkers command to the ICMP DoS attack traffic.
      Note   

      For more information on the fields in the display output of the show ip cache verbose flow command, refer to the Cisco IOS NetFlow Command Reference .

      If you are using the Top Talkers feature to analyze a network threat and you are not able to use the basic match filters to limit the display of the show ip flow top-talkers command to the traffic that you are analyzing, you can use NetFlow filtering and sampling to limit the traffic that shows up in the display of the show ip flow top-talkers command. The process for configuring NetFlow filtering and sampling is explained in the Configuring NetFlow Filtering and Sampling.

      Configuring NetFlow Filtering and Sampling

      If you use the show ip cache flow command or the show ip cache verbose flow command to display the flows in the cache, you will see the ICMP flows that are selected by NetFlow filtering and sampling on interface Ethernet0/0.1, and flows for all NetFlow supported traffic types on any other interfaces that NetFlow is running on. The show ip flow top-talkers [verbose] command is used to display the flow status and statistics for the traffic type you configured with the match criteria over interfaces to which you applied the service policy. For example, in this case you configured top talkers to match on ICMP traffic sent from any host that is arriving on Ethernet0/0.1 and destined for 172.16.10.2.

      In this task the Top Talkers feature is being used more as a flow filter to separate flows of interest from all of the flows the router is seeing, rather than a filter to display the flows with the highest traffic volumes. Top talkers is used in this manner because in this example all of the ICMP DoS attack flows are of interest, not just the flows with the highest volumes. This is why a large value is assigned to the top keyword in the top talkers configuration. Setting the value for the top keyword to 50 when the largest number of ICMP DoS attack flows tracked by the router is 12 ensures that all of the ICMP DoS attack flows will be tracked.

      If your router sees a significant number of flows involved in a DoS attack, you might want to set the value for the top keyword to a number that is less than the total number of flows to limit the number of flows that you see in the display when you use the show ip flow top-talkerscommand. This will ensure that you are seeing the flows that have the highest volume of DoS attack traffic. However, if all of the flows have the same traffic volume, the show ip flow top-talkerscommand will not be able to differentiate between them. It displays the number of flows that you set the value of the top keyword to, starting from the first flow in the cache.

      Perform the following task to configure NetFlow Filtering and sampling.


      Note


      Restrictions for NetFlow Input Filters

      On Cisco 7500 platforms, the NetFlow Input Filters feature is supported only in distributed mode.

      Restrictions for Random Sampled NetFlow

      If full NetFlow is enabled on an interface, it takes precedence over Random Sampled NetFlow (which will thus have no effect). Disable full NetFlow on an interface before enabling Random Sampled NetFlow on that interface.

      Enabling Random Sampled NetFlow on a physical interface does not automatically enable Random Sampled NetFlow on subinterfaces; you must explicitly configure it on subinterfaces. Also, disabling Random Sampled NetFlow on a physical interface (or a subinterface) does not enable full NetFlow. This restriction prevents the transition to full NetFlow from overwhelming the physical interface (or subinterface). If you want full NetFlow, you must explicitly enable it.

      You must use NetFlow Version 9 if you want to use sampler option templates or view NetFlow sampler IDs.


      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    flow-sampler-map sampler-map-name

        4.    mode random one-out-of packet-interval

        5.    exit

        6.    class-map class-map-name [match-all | match-any]

        7.    match access-group access-group

        8.    exit

        9.    policy-map policy-map-name

        10.    class { class-name | class-default}

        11.    netflow-sampler sampler-map-name

        12.    exit

        13.    exit

        14.    interface interface-type interface-number [.subinterface number]

        15.    no [ip route-cache flow | ip flow ingress]

        16.    service-policy {input | output} policy-map-name

        17.    exit

        18.    ip flow-top-talkers

        19.    top number

        20.    sort-by packets

        21.    match class-map claas-name

        22.    no match destination address ip-address /prefix-mask

        23.    exit

        24.    access-list access-list-number permit icmp source destination

        25.    end


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Router> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.

         
        Step 2 configure terminal


        Example:
        Router# configure terminal
         

        Enters global configuration mode.

         
        Step 3 flow-sampler-map sampler-map-name


        Example:
        Router(config)# flow-sampler-map icmp-dos-fs-map
         

        Defines a statistical sampling NetFlow export flow sampler map.

        • The sampler-map-name argument is the name of the flow sampler map to be defined.

        Entering the flow-sampler-map command enables the flow sampler configuration mode.

         
        Step 4 mode random one-out-of packet-interval


        Example:
        Router(config-sampler-map)# mode random one-out-of 2
         

        Specifies a statistical sampling NetFlow export random sampling mode and a packet interval.

        • The random keyword specifies that sampling uses the random sampling mode.

        • The one-out-of packet-interval argument-keyword pair specifies the packet interval (one out of every npackets) from which to sample. For n, you can specify from 1 to 65535 (packets).

         
        Step 5 exit


        Example:
        Router(config-sampler-map)# exit
         

        Exits back to global configuration mode.

         
        Step 6 class-map class-map-name [match-all | match-any]


        Example:
        Router(config)# class-map match-any icmp-dos-class-map
         

        Creates a class map to be used for matching packets to a specified class.

        • The class-map-name argument is the name of the class for the class map. The name can be a maximum of 40 alphanumeric characters. The class name is used for both the class map and for configuring policy for the class in the policy map.

        • The match-all | match-anykeywords determine how packets are evaluated when multiple match criteria exist. Packets must either meet all of the match criteria (match-all) or only one of the match criteria (match-any) to be considered a member of the class.

        Entering the class-mapcommand enables class-map configuration mode, in which you can enter one of the match commands to configure the match criteria for this class.

         
        Step 7 match access-group access-group


        Example:
        Router(config-cmap)# match access-group 101
         

        Configures the match criteria for a class map on the basis of the specified access control list (ACL).

        • The access-group argument is a numbered ACL whose contents are used as the match criteria against which packets are checked to determine if they belong to this class. An ACL number can be a number from 1 to 2699.

         
        Step 8 exit


        Example:
        Router(config-cmap)# exit
         

        Exits back to global configuration mode.

         
        Step 9 policy-map policy-map-name


        Example:
        Router(config)# policy-map icmp-dos-policy-map
         

        Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy.

        • The policy-map-name argument is the name of the policy map. The name can be a maximum of 40 alphanumeric characters.

        Entering the policy-mapcommand enables quality of service (QoS) policy-map configuration mode, in which you can configure or modify the class policies for that policy map

         
        Step 10 class { class-name | class-default}


        Example:
        Router(config-pmap)# class icmp-dos-class-map
         

        Specifies the name of the class whose policy you want to create or change or specifies the default class (commonly known as the class-default class) before you configure its policy.

        • The class-name argument is the name of the class for which you want to configure or modify policy.

        • The class-default keyword specifies the default class so that you can configure or modify its policy.

        Entering the class command enables QoS policy-map class configuration mode.

         
        Step 11 netflow-sampler sampler-map-name


        Example:
        Router(config-pmap-c)# netflow-sampler icmp-dos-fs-map
         

        Enables a NetFlow input filter sampler.

        • The sampler-map-name argument is the name of the NetFlow sampler map to apply to the class.

        You can assign only one NetFlow input filter sampler to a class. Assigning another NetFlow input filter sampler to a class overwrites the previous one.

         
        Step 12 exit


        Example:
        Router(config-pmap-c)# exit
         

        Exits back to policy-map configuration mode.

         
        Step 13 exit


        Example:
        Router(config-pmap# exit
         

        Exits back to global configuration mode.

         
        Step 14 interface interface-type interface-number [.subinterface number]


        Example:
        Router(config)# interface Ethernet0/0.1
         

        Specifies the interface and enters subinterface configuration mode.

        • The interface-type argument is the type of interface to be configured.

        • The interface-numberargument is the number of the interface. Refer to the appropriate hardware manual for slot and port information.

         
        Step 15 no [ip route-cache flow | ip flow ingress]


        Example:
        Router(config-subif)# no ip flow ingress
         

        Removes the existing NetFlow command from the interface.

        Note   

        NetFlow sampling and filtering can not start if there is another command on the interface that is enabling NetFlow.

         
        Step 16 service-policy {input | output} policy-map-name


        Example:
        Router(config-subif)# service-policy input icmp-dos-policy-map
         

        Attaches a policy map to an input interface or virtual circuit (VC), or an output interface or VC, to be used as the service policy for that interface or VC.

        • The input keyword attaches the specified policy map to the input interface or input VC.

        • The output keyword attaches the specified policy map to the output interface or output VC.

        • The policy-map-name is the name of a service policy map (created through use of the policy-map command) to be attached. The name can be a maximum of 40 alphanumeric characters.

         
        Step 17 exit


        Example:
        Router(config-subif)# exit
         

        Exits back to global configuration mode.

         
        Step 18 ip flow-top-talkers


        Example:
        Router(config)# ip flow-top-talkers
         

        Enters NetFlow top talkers configuration mode.

         
        Step 19 top number


        Example:
        Router(config-flow-top-talkers)# top 50
         

        Specifies the maximum number of top talkers that will be retrieved by a NetFlow top talkers query.

         
        Step 20 sort-by packets


        Example:
        Router(config-flow-top-talkers)# sort-by packets
         

        Specifies the sort criterion for the top talkers.

        • The top talkers can be sorted either by the total number of packets of each top talker or the total number of bytes of each top talker.

         
        Step 21 match class-map claas-name


        Example:
        Router(config-flow-top-talkers)# match class-map icmp-dos-class-map
         

        Specifies that the match criteria should be obtained from the class-map.

         
        Step 22 no match destination address ip-address /prefix-mask


        Example:
        Router(config-flow-top-talkers)# no match destination address 172.16.10.2/32
         

        (Optional) If you still have a match entry for the destination address you should remove it so that only the class-name match criteria is used.

         
        Step 23 exit


        Example:
        Router(config-sampler-map)# exit
         

        Exits back to global configuration mode.

         
        Step 24 access-list access-list-number permit icmp source destination


        Example:
        Router(config)# access-list 101 permit icmp any host 172.16.10.2
         

        Creates an extended access list that is used to track any host that is sending ICMP traffic to 172.16.10.2.

         
        Step 25 end


        Example:
        Router(config)# end
         

        Exits to privileged EXEC mode.

         

        Verify NetFlow Filtering and Sampling

        To verify that filtering and sampling is working properly, use the following step.

        SUMMARY STEPS

          1.    show flow-sampler


        DETAILED STEPS
        show flow-sampler

        Any non-zero value in the display output below indicates that Filtering and sampling is active.



        Example:
        Router# show flow-sampler
         
        Sampler : icmp-dos-fs-map, id : 1, packets matched : 63226, mode : random sampling mode
          sampling interval is : 2
        Router

        Monitoring and Analyzing the Sampled and Filtered NetFlow Top Talkers Flows

        To monitor and analyze the filtered and sampled NetFlow top talkers flows use the following step.

        SUMMARY STEPS

          1.    show ip flow top-talkers

          2.    show ip flow top-talkers verbose


        DETAILED STEPS
          Step 1   show ip flow top-talkers

          The following sample output shows the six traffic flows that are being sent to the host with IP address 172.16.10.2.



          Example:
          Router# show ip flow top-talkers
          SrcIf         SrcIPaddress    DstIf         DstIPaddress    Pr SrcP DstP Bytes
          Et0/0.1       10.231.185.254  Et1/0.1       172.16.10.2     01 0000 0C01  5460 
          Et0/0.1       10.106.1.1      Et1/0.1       172.16.10.2     01 0000 0800  5124 
          Et0/0.1       10.132.221.111  Et1/0.1       172.16.10.2     01 0000 0800  5012 
          Et0/0.1       10.251.138.218  Et1/0.1       172.16.10.2     01 0000 0C01  4844 
          Et0/0.1       10.10.12.1      Et1/0.1       172.16.10.2     01 0000 0C01  4704 
          Et0/0.1       10.71.200.138   Et1/0.1       172.16.10.2     01 0000 0C01  4396 
          6 of 50 top talkers shown. 6 of 7 flows matched.
          
          Step 2   show ip flow top-talkers verbose

          The following sample output below shows the details for the six traffic flows that are being sent to the host with IP address 172.16.10.2.



          Example:
          Router# show ip flow top-talkers verbose
           
          SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs Bytes
          Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
          Et0/0.1        10.106.1.1      Et1/0.1        172.16.10.2     01 00  10    2884 
          0000 /0  0                     0800 /0  0     0.0.0.0                28    64.6
          Sampler: 1  Class: 1  
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       28                            Max plen:        28
          Min TTL:        59                            Max TTL:         59
          ICMP type:       8                            ICMP code:        0
          IP id:           0
          Et0/0.1        10.132.221.111  Et1/0.1        172.16.10.2     01 00  10    2828 
          0000 /0  0                     0800 /0  0     0.0.0.0                28    64.6
          Sampler: 1  Class: 1  
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       28                            Max plen:        28
          Min TTL:        59                            Max TTL:         59
          ICMP type:       8                            ICMP code:        0
          IP id:           0
          Et0/0.1        10.231.185.254  Et1/0.1        172.16.10.2     01 00  10    2716 
          0000 /0  0                     0C01 /0  0     0.0.0.0                28    64.6
          Sampler: 1  Class: 1  
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       28                            Max plen:        28
          Min TTL:        59                            Max TTL:         59
          ICMP type:      12                            ICMP code:        1
          IP id:           0
          Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  10    2548 
          0000 /0  0                     0C01 /0  0     0.0.0.0                28    58.0
          Sampler: 1  Class: 1  
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       28                            Max plen:        28
          Min TTL:        59                            Max TTL:         59
          ICMP type:      12                            ICMP code:        1
          IP id:           0
          Et0/0.1        10.251.138.218  Et1/0.1        172.16.10.2     01 00  10    2436 
          0000 /0  0                     0C01 /0  0     0.0.0.0                28    64.6
          Sampler: 1  Class: 1  
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       28                            Max plen:        28
          Min TTL:        59                            Max TTL:         59
          ICMP type:      12                            ICMP code:        1
          IP id:           0
          Et0/0.1        10.10.12.1      Et1/0.1        172.16.10.2     01 00  10    2352 
          0000 /0  0                     0C01 /0  0     0.0.0.0                28    57.7
          Sampler: 1  Class: 1  
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       28                            Max plen:        28
          Min TTL:        59                            Max TTL:         59
          ICMP type:      12                            ICMP code:        1
          IP id:           0
          6 of 50 top talkers shown. 6 of 7 flows matched.
          

          Configuration Examples for Detecting and Analyzing Network Threats With NetFlow

          Configuring NetFlow Layer 2 and Sec Mon Exports to Capture Traffic From a Simulated FTP Attack Example

          The following example shows how to use the NetFlow Layer 2 and Security Monitoring Exports feature to find out whether your network is being attacked by a host that is sending fake FTP traffic in an attempt to overwhelm the FTP server. This attack might cause end users to see a degradation in the ability of the FTP server to accept new connections or to service existing connections.

          This example uses the network shown in the figure below. Host A is sending fake FTP packets to the FTP server.

          This example also shows you how to use the Layer 2 data captured by the NetFlow Layer 2 and Security Monitoring Exports feature to learn where the traffic is originating and what path it is taking through the network.

          Figure 7. Test Network


          Tip


          Keep track of the MAC addresses and IP addresses of the devices in your network. You can use them to analyze attacks and to resolve problems.



          Note


          This example does not include the ip flow-capture icmpcommand that captures the value of the ICMP type and code fields. The use of the ip flow-capture icmp command is described in "Configuring NetFlow Layer 2 and Sec Mon Exports to Capture Traffic From a Simulated ICMP Attack Example."


          R2

          !
          hostname R2
          !
          interface Ethernet0/0
           mac-address aaaa.bbbb.cc02
           ip address 172.16.1.2 255.255.255.0
          !
          interface Ethernet1/0
           mac-address aaaa.bbbb.cc03
           no ip address
          !
          interface Ethernet1/0.1
           encapsulation dot1Q 5
           ip address 172.16.6.1 255.255.255.0
          !
          !
          router rip
           version 2
           network 172.16.0.0
           no auto-summary
          !

          R3

          !
          hostname R3
          !
          ip flow-capture fragment-offset
          ip flow-capture packet-length
          ip flow-capture ttl
          ip flow-capture vlan-id
          ip flow-capture ip-id
          ip flow-capture mac-addresses
          !
          interface Ethernet0/0
           mac-address aaaa.bbbb.cc04
           no ip address
          !
          interface Ethernet0/0.1
           encapsulation dot1Q 5
           ip address 172.16.6.2 255.255.255.0
           ip accounting output-packets
           ip flow ingress
          !
          interface Ethernet1/0
           mac-address aaaa.bbbb.cc05
           no ip address
          !
          interface Ethernet1/0.1
           encapsulation dot1Q 6
           ip address 172.16.7.1 255.255.255.0
           ip accounting output-packets
           ip flow egress
          !
          router rip
           version 2
           network 172.16.0.0
           no auto-summary
          !

          R4

          !
          hostname R4
          !
          interface Ethernet0/0
           mac-address aaaa.bbbb.cc07
           ip address 172.16.10.1 255.255.255.0
          !
          interface Ethernet1/0
           mac-address aaaa.bbbb.cc06
           no ip address
          !
          interface Ethernet1/0.1
           encapsulation dot1Q 6
           ip address 172.16.7.2 255.255.255.0
          !
          router rip
           version 2
           network 172.16.0.0
           no auto-summary
          !
          

          Analyze an FTP DoS Attack Using the show ip cache verbose flow command Example

          The show ip cache verbose flow command displays the NetFlow flows. You can use this display output to identify the path that the FTP traffic from Host A is taking as it is received and transmitted by R3.


          Note


          To reduce the space required to display the output from the show ip flow cache verbose flowcommand only the FTP flows are shown.



          Tip


          Look for the flows that have FTP in them and make a note of the interfaces, MAC addresses, and VLANs (if applicable) for the flows.


          R3# show ip cache verbose flow
           
          IP packet size distribution (189118 total packets):
             1-32   64   96  128  160  192  224  256  288  320  352  384  416  448  480
             .043 .610 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
              512  544  576 1024 1536 2048 2560 3072 3584 4096 4608
             .000 .000 .173 .000 .173 .000 .000 .000 .000 .000 .000
          IP Flow Switching Cache, 278544 bytes
            25 active, 4071 inactive, 615 added
            263794 ager polls, 0 flow alloc failures
            Active flows timeout in 30 minutes
            Inactive flows timeout in 15 seconds
          IP Sub Flow Cache, 25736 bytes
            50 active, 974 inactive, 1648 added, 615 added to flow
            0 alloc failures, 0 force free
            1 chunk, 1 chunk added
            last clearing of statistics never
          Protocol         Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)
          --------         Flows     /Sec     /Flow  /Pkt     /Sec     /Flow     /Flow
          TCP-FTP             12      0.0       895    40      0.9    1363.8       5.5
          TCP-FTPD            12      0.0       895    40      0.9    1363.8       5.6
          Total:             590      0.0       317   383     16.1     430.1      12.4
          Et0/0.1        192.168.87.200  Et1/0.1        172.16.10.2     06 00  00      63 
          0015 /0  0                     0015
           /0  0     0.0.0.0                40    94.5
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          Et0/0.1        192.168.87.200  Et1/0.1        172.16.10.2     06 00  00      63 
          0014 /0  0                     0014
           /0  0     0.0.0.0                40    94.5
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          Et0/0.1        10.10.10.2      Et1/0.1        172.16.10.2     06 00  00      64 
          0015 /0  0                     0015
           /0  0     0.0.0.0                40    96.0
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          Et0/0.1        10.10.10.2      Et1/0.1        172.16.10.2     06 00  00      64 
          0014 /0  0                     0014
           /0  0     0.0.0.0                40    96.0
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          Et0/0.1        10.234.53.1     Et1/0.1        172.16.10.2     06 00  00      63 
          0015 /0  0                     0015
           /0  0     0.0.0.0                40    94.5
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          Et0/0.1        10.234.53.1     Et1/0.1        172.16.10.2     06 00  00      63 
          0014 /0  0                     0014
           /0  0     0.0.0.0                40    94.5
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          Et0/0.1        172.30.231.193  Et1/0.1        172.16.10.2     06 00  00      63 
          0015 /0  0                     0015
           /0  0     0.0.0.0                40    94.5
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          Et0/0.1        172.30.231.193  Et1/0.1        172.16.10.2     06 00  00      63 
          0014 /0  0                     0014
           /0  0     0.0.0.0                40    94.5
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          

          There are 8 FTP flows shown in the output. You can use the Layer 2 information in the flows that is captured by the ip flow-capture command to identify the path the traffic is taking through the network. In this example, the traffic is being sent to R3 on VLAN 5 by R2. You can demonstrate that R2 is transmitting the traffic over interface 1/0.1 because the source MAC address (aaaa.bbb.cc03) belongs to 1/0.1 on R2. You can demonstrate that R3 is transmitting the traffic using VLAN 6 on interface 1/0.1 to interface 1/0.1 on R4, because the destination MAC address (aaaa.bbbb.cc06) belongs to interface 1/0.1 on R4.


          Note


          For more information on the ip flow-capture command, and the fields in the display output of the show ip cache verbose flow command, refer to the Cisco IOS NetFlow Command Reference .


          You can use this information to mitigate this attack. One possible way to mitigate this attack is by configuring an extended IP access list that blocks all FTP traffic from the source IP addresses that Host A is spoofing and applying it Ethernet 0/0 on R2.

          Analyze an FTP DoS Attack Using NetFlow Dynamic Top Talkers CLI Example

          You can use the NetFlow Dynamic Top Talkers CLI feature to quickly identify the FTP top talkers in the network traffic that might be sending the traffic. This will show you the IP source addresses that Host A is using as it sends the DoS attack traffic.

          R3# show ip flow top 50 aggregate source-address sorted-by bytes descending match destination-port min 20 max 21
          There are 5 top talkers:
          IPV4 SRC-ADDR         bytes        pkts       flows
          ===============  ==========  ==========  ==========
          10.231.185.254         5640         141           2
          10.132.221.111         3680          92           2
          10.10.12.1             3640          91           2
          10.251.138.218         3600          90           2
          10.71.200.138          1880          47           1
          9 of 34 flows matched.
          

          Note


          Only source IP addresses from FTP traffic are shown because of the match destination-port min 20 max 21 criteria. The source addresses are aggregated together so only the most relevant sources are shown.



          Note


          Only nine of the 34 flows matched because the rest of the flows are not FTP flows, therefore they do not meet the match criteria (match destination-port min 20 max 21).



          Tip


          The top talkers are displayed in descending order of the aggregated field by default.



          Tip


          You can enter the port numbers in their decimal values as shown, or in their hexadecimal equivalents of 0x14 and 0x15.


          After you have identified FTP top talkers traffic you need to identify the source IP addresses of IP traffic that is being sent to the host that you believe is under attack.

          R3# show ip flow top 50 aggregate source-address match destination-prefix 172.16.10.2/32
          There are 6 top talkers:
          IPV4 SRC-ADDR         bytes        pkts       flows
          ===============  ==========  ==========  ==========
          10.251.138.218         6642          18           4
          10.231.185.254         5068          28           4
          10.132.221.111        14818          25           4
          10.106.1.1            12324          12           2
          10.71.200.138         12564          18           3
          10.10.12.1              560          14           2
          19 of 33 flows matched.
          

          Tip


          You can specify the host that you believe is under attack by using a prefix value of 32 with the match destination-prefix command.



          Note


          Only 19 of the 33 flows matched because the rest of the flows do not contain traffic that is destined for the host with the IP address of 172.16.10.2, therefore they do not meet the match criteria (match destination-prefix 172.16.10.2/32).


          The final step is to cross reference the source IP addresses of any hosts that are sending any IP traffic to the host under attack with the list of source IP addresses from the FTP top talkers. This is required because the show ip flow top command does not support multiple match criteria. Therefore you cannot limit the top talkers to FTP traffic being sent to a specific host with a single show ip flow top command (match destination-port min 20 max 21 <and> match destination-prefix 172.16.10.2/32).

          The host with the IP address of 10.106.1.1 is apparently not involved in this DoS attack because it is not in the display output from the show ip flow top 50 aggregate source-address sorted-by bytes descending match destination-port min 20 max 21 command. This means that it is not sending FTP traffic to the host that is under attack.

          Therefore the host IP addressees involved in this FTP DoS attack are likely to be:

          • 10.231.185.254

          • 10.132.221.111

          • 10.10.12.1

          • 10.251.138.218

          • 10.71.200.138

          Now that you know the source addresses of the FTP traffic you can configure an extended access list that blocks FTP traffic from these address, and apply it to the interface that is closest to the point the traffic is entering your network.


          Note


          Unless you recognize that some of the source IP addresses are not legitimate IP addresses for your network it might not be possible to identify legitimate FTP traffic from FTP DoS attack traffic.


          Configuring NetFlow Layer 2 and Sec Mon Exports to Capture Traffic From a Simulated ICMP Attack Example

          The following example shows how to use the NetFlow Layer 2 and Security Monitoring Exports feature to find out that your network is being attacked by ICMP traffic. It uses the network shown in the figure below. Host A is sending ICMP ping packets to the FTP server.

          Figure 8. Test Network


          Tip


          Keep track of the MAC addresses and IP addresses of the devices in your network. You can use them to analyze attacks and to resolve problems.


          R2

          !
          hostname R2
          !
          interface Ethernet0/0
           mac-address aaaa.bbbb.cc02
           ip address 172.16.1.2 255.255.255.0
          !
          interface Ethernet1/0
           mac-address aaaa.bbbb.cc03
           no ip address
          !
          interface Ethernet1/0.1
           encapsulation dot1Q 5
           ip address 172.16.6.1 255.255.255.0
          !
          !
          router rip
           version 2
           network 172.16.0.0
           no auto-summary
          !

          R3

          !
          hostname R3
          !
          ip flow-capture fragment-offset
          ip flow-capture packet-length
          ip flow-capture ttl
          ip flow-capture vlan-id
          ip flow-capture icmp
          ip flow-capture ip-id
          ip flow-capture mac-addresses
          !
          interface Ethernet0/0
           mac-address aaaa.bbbb.cc04
           no ip address
          !
          interface Ethernet0/0.1
           encapsulation dot1Q 5
           ip address 172.16.6.2 255.255.255.0
           ip accounting output-packets
           ip flow ingress
          !
          interface Ethernet1/0
           mac-address aaaa.bbbb.cc05
           no ip address
          !
          interface Ethernet1/0.1
           encapsulation dot1Q 6
           ip address 172.16.7.1 255.255.255.0
           ip accounting output-packets
           ip flow egress
          !
          router rip
           version 2
           network 172.16.0.0
           no auto-summary
          !

          R4

          !
          hostname R4
          !
          interface Ethernet0/0
           mac-address aaaa.bbbb.cc07
           ip address 172.16.10.1 255.255.255.0
          !
          interface Ethernet1/0
           mac-address aaaa.bbbb.cc06
           no ip address
          !
          interface Ethernet1/0.1
           encapsulation dot1Q 6
           ip address 172.16.7.2 255.255.255.0
          !
          router rip
           version 2
           network 172.16.0.0
           no auto-summary
          !

          Analyze an ICMP Ping DoS Attack Using the show ip cache verbose flow command Example

          The show ip cache verbose flow command displays the NetFlow flows. You can use this display output to identify the path that the ICMP traffic from Host A is taking as it is received and transmitted by R3.


          Note


          To reduce the space required to display the output from the show ip flow cache verbose flowcommand only the ICMP flows are shown.



          Tip


          Look for the flows that have ICMP in them and make a note of the interfaces, MAC addresses, and VLANs (if applicable) for the flows.


          R3# show ip cache verbose flow
          IP packet size distribution (122369 total packets):
             1-32   64   96  128  160  192  224  256  288  320  352  384  416  448  480
             .065 .665 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
              512  544  576 1024 1536 2048 2560 3072 3584 4096 4608
             .000 .000 .134 .000 .134 .000 .000 .000 .000 .000 .000
          IP Flow Switching Cache, 278544 bytes
            24 active, 4072 inactive, 404 added
            176657 ager polls, 0 flow alloc failures
            Active flows timeout in 30 minutes
            Inactive flows timeout in 15 seconds
          IP Sub Flow Cache, 25736 bytes
            48 active, 976 inactive, 1088 added, 404 added to flow
            0 alloc failures, 0 force free
            1 chunk, 1 chunk added
            last clearing of statistics never
          Protocol         Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)
          --------         Flows     /Sec     /Flow  /Pkt     /Sec     /Flow     /Flow
          ICMP                27      0.0      1131   763      3.9    1557.4       3.6
          Total:             380      0.0       267   257     13.0     382.8      12.6
          SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs  Pkts
          Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
          Et0/0.1        10.106.1.1      Et1/0.1        172.16.10.2     01 00  10     864 
          0000 /0  0                     0800 /0  0     0.0.0.0              1500  1089.9
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      1500                            Max plen:       1500
          Min TTL:        59                            Max TTL:         59
          ICMP type:       8                            ICMP code:        0
          IP id:           0
          Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  00     864 
          0000 /0  0                     0000 /0  0     0.0.0.0               554  1090.0
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      554                            Max plen:       554
          Min TTL:        59                            Max TTL:         59
          ICMP type:       0                            ICMP code:        0
          IP id:           0                            FO:            185
          Et0/0.1        10.231.185.254  Et1/0.1        172.16.10.2     01 00  00     864 
          0000 /0  0                     0000 /0  0     0.0.0.0               554  1090.0
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      554                            Max plen:       554
          Min TTL:        59                            Max TTL:         59
          ICMP type:       0                            ICMP code:        0
          IP id:           0                            FO:            185
          Et0/0.1        10.10.12.1      Et1/0.1        172.16.10.200   01 00  00     864 
          0000 /0  0                     0000 /0  0     0.0.0.0               554  1090.0
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      554                            Max plen:       554
          Min TTL:        59                            Max TTL:         59
          ICMP type:       0                            ICMP code:        0
          IP id:           0                            FO:            185
          Et0/0.1        10.132.221.111  Et1/0.1        172.16.10.2     01 00  10     864 
          0000 /0  0                     0800 /0  0     0.0.0.0              1500  1089.9
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      1500                            Max plen:       1500
          Min TTL:        59                            Max TTL:         59
          ICMP type:       8                            ICMP code:        0
          IP id:           0
          Et0/0.1        10.251.138.218  Et1/0.1        172.16.10.2     01 00  00     864 
          0000 /0  0                     0000 /0  0     0.0.0.0               554  1089.9
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      554                            Max plen:       554
          Min TTL:        59                            Max TTL:         59
          ICMP type:       0                            ICMP code:        0
          IP id:           0                            FO:            185
          Et0/0.1        10.10.12.1      Et1/0.1        172.16.10.200   01 00  10     864 
          0000 /0  0                     0C01 /0  0     0.0.0.0              1500  1090.0
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      1500                            Max plen:       1500
          Min TTL:        59                            Max TTL:         59
          ICMP type:      12                            ICMP code:        1
          IP id:           0
          Et0/0.1        10.106.1.1      Et1/0.1        172.16.10.2     01 00  00     864 
          0000 /0  0                     0000 /0  0     0.0.0.0               554  1089.9
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      554                            Max plen:       554
          Min TTL:        59                            Max TTL:         59
          ICMP type:       0                            ICMP code:        0
          IP id:           0                            FO:            185
          Et0/0.1        10.251.138.218  Et1/0.1        172.16.10.2     01 00  10     864 
          0000 /0  0                     0C01 /0  0     0.0.0.0              1500  1089.9
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      1500                            Max plen:       1500
          Min TTL:        59                            Max TTL:         59
          ICMP type:      12                            ICMP code:        1
          IP id:           0
          Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  10     864 
          0000 /0  0                     0C01 /0  0     0.0.0.0              1500  1090.0
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      1500                            Max plen:       1500
          Min TTL:        59                            Max TTL:         59
          ICMP type:      12                            ICMP code:        1
          IP id:           0
          Et0/0.1        10.132.221.111  Et1/0.1        172.16.10.2     01 00  00     864 
          0000 /0  0                     0000 /0  0     0.0.0.0               554  1089.9
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      554                            Max plen:       554
          Min TTL:        59                            Max TTL:         59
          ICMP type:       0                            ICMP code:        0
          IP id:           0                            FO:            185
          Et0/0.1        10.231.185.254  Et1/0.1        172.16.10.2     01 00  10     864 
          0000 /0  0                     0C01 /0  0     0.0.0.0              1500  1090.0
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:      1500                            Max plen:       1500
          Min TTL:        59                            Max TTL:         59
          ICMP type:      12                            ICMP code:        1
          IP id:           0
          

          There are 12 ICMP flows shown in the output. You can use the Layer 2 information in the flows that is captured by the ip flow-capture command to identify the path the traffic is taking through the network. In this example, the traffic is being sent to R3 on VLAN 5 by R2. You can demonstrate that R2 is transmitting the traffic over interface 1/0.1 because the source MAC address (aaaa.bbb.cc03) belongs to 1/0.1 on R2. You can demonstrate that R3 is transmitting the traffic using VLAN 6 on interface 1/0.1 to interface 1/0.1 on R4, because the destination MAC address (aaaa.bbbb.cc06) belongs to interface 1/0.1 on R4.


          Note


          For more information on the ip flow-capture command, and the fields in the display output of the show ip cache verbose flow command, refer to the Cisco IOS NetFlow Command Reference .


          You can use this information to mitigate this attack. One possible way to mitigate this attack is by configuring an extended IP access list that blocks all ICMP traffic from the source IP addresses that Host A is spoofing and applying it Ethernet 0/0 on R2.

          Analyze an ICMP Ping DoS Attack Using NetFlow Dynamic Top Talkers CLI Example

          You can use the NetFlow Dynamic Top Talkers CLI feature to quickly identify the ICMP top talkers in the network traffic that might be sending the traffic. This will show you the IP source addresses that Host A is using as it sends the DoS attack traffic.

          R3# show ip flow top 50 aggregate icmp
          There are 3 top talkers:
          ICMP TYPE  ICMP CODE       bytes        pkts       flows
          =========  =========  ==========  ==========  ==========
                 12          1     2466000        1644           4
                  8          0     1233000         822           2
                  0          0     1366164        2466           6
          12 of 25 flows matched.
          

          Note


          Only 12 of the 25 flows matched because the rest of the flows are not ICMP flows.



          Tip


          The top talkers are displayed in descending order of the aggregated field by default.


          After you have identified the ICMP types and code values in the network traffic, you need to determine the source IP addresses for the ICMP traffic that being sent to the FTP server.

          R3# show ip flow top 50 aggregate source-address match icmp type 12 code 1
          There are 4 top talkers:
          IPV4 SRC-ADDR         bytes        pkts       flows
          ===============  ==========  ==========  ==========
          10.251.138.218       867000         578           1
          10.231.185.254       865500         577           1
          10.71.200.138        865500         577           1
          10.10.12.1           867000         578           1
          4 of 24 flows matched.
          

          Note


          Only source IP addresses from ICMP traffic are shown because of the match icmp type 12 code 1 criteria. No aggregation is performed on the source IP addresses because there is only one flow for IP each address.



          Note


          Only four of the 24 flows matched because the rest of the flows did not meet the match criteria (match icmp type 12 code 1).


          R3# show ip flow top 50 aggregate source-address match icmp type 8 code 0
           
          There are 2 top talkers:
          IPV4 SRC-ADDR         bytes        pkts       flows
          ===============  ==========  ==========  ==========
          10.132.221.111      1095000         730           1
          10.106.1.1          1095000         730           1
          2 of 24 flows matched.
          

          Note


          Only source IP addresses from ICMP traffic are shown because of the match icmp type 8 code 0 criteria. No aggregation is performed on the source IP addresses because there is only one flow for IP each address.



          Note


          Only two of the 24 flows matched because the rest of the flows did not meet the match criteria (match icmp type 8 code 0).


          R3# show ip flow top 50 aggregate source-address match icmp type 0 code 0
          There are 6 top talkers:
          IPV4 SRC-ADDR         bytes        pkts       flows
          ===============  ==========  ==========  ==========
          10.251.138.218       416608         752           1
          10.231.185.254       416608         752           1
          10.132.221.111       416608         752           1
          10.106.1.1           416608         752           1
          10.71.200.138        416608         752           1
          10.10.12.1           416608         752           1
          6 of 24 flows matched.
          

          Note


          Only source IP addresses from ICMP traffic are shown because of the match icmp type 0 code 0 criteria. No aggregation is performed on the source IP addresses because there is only one flow for IP each address.



          Note


          Only six of the 24 flows matched because the rest of the flows did not meet the match criteria (match icmp type 0 code 0).


          The next step is to create a list of the source IP addresses that Host A is using.

          • 10.251.138.218

          • 10.231.185.254

          • 10.71.200.138

          • 10.10.12.1

          • 10.132.221.111

          • 10.106.1.1.

          Now that you know the source addresses of the ICMP DoS attack traffic, you can mitigate this attack by configuring an extended access list that blocks ICMP traffic from these address and applying it to the interface that is closest to the point that the traffic is entering your network.

          Configure NetFlow Filtering and Sampling Example

          This example configuration contains the configuration commands required to use NetFlow filtering and sampling on the NetFlow router.

          !
          hostname Router
          !
          ip cef
          !
          flow-sampler-map icmp-dos-fs-map
           mode random one-out-of 2
          !
          !
          class-map match-any icmp-dos-class-map
           match access-group 101
          !
          !
          policy-map icmp-dos-policy-map
            class icmp-dos-class-map
             netflow-sampler icmp-dos-fs-map
          !
          interface Ethernet0/0
           mac-address aaaa.bbbb.cc04
           no ip address
          !
          interface Ethernet0/0.1
           encapsulation dot1Q 5
           ip address 172.16.6.2 255.255.255.0
           service-policy input icmp-dos-policy-map
          !
          interface Ethernet1/0.1
           encapsulation dot1Q 6
           ip address 172.16.7.1 255.255.255.0
           ip flow egress
          !
          ip flow-capture fragment-offset
          ip flow-capture packet-length
          ip flow-capture ttl
          ip flow-capture vlan-id
          ip flow-capture icmp
          ip flow-capture ip-id
          ip flow-capture mac-addresses
          !
          ip flow-top-talkers
           top 5
           sort-by bytes
           match class-map icmp-dos-class-map
          !
          access-list 101 permit icmp any host 172.16.10.2
          !
          end
          

          Where to Go Next

          See the "Additional References" section for links to configuration information about additional NetFlow features and services.

          Additional References

          Related Documents

          Related Topic

          Document Title

          Overview of Cisco IOS NetFlow

          "Cisco IOS NetFlow Overview"

          The minimum information about and tasks required for configuring NetFlow and NetFlow Data Export

          "Getting Started with Configuring NetFlow and NetFlow Data Export"

          Tasks for configuring NetFlow to capture and export network traffic data

          "Configuring NetFlow and NetFlow Data Export"

          Tasks for configuring Configuring MPLS Aware NetFlow

          Configuring MPLS Aware NetFlow

          Tasks for configuring MPLS egress NetFlow accounting

          Configuring MPLS Egress NetFlow Accounting and Analysis

          Tasks for configuring NetFlow input filters

          "Using NetFlow Filtering or Sampling to Select the Network Traffic to Track"

          Tasks for configuring Random Sampled NetFlow

          "Using NetFlow Filtering or Sampling to Select the Network Traffic to Track"

          Tasks for configuring NetFlow aggregation caches

          "Configuring NetFlow Aggregation Caches"

          Tasks for configuring NetFlow BGP next hop support

          "Configuring NetFlow BGP Next Hop Support for Accounting and Analysis"

          Tasks for configuring NetFlow multicast support

          "Configuring NetFlow Multicast Accounting"

          Tasks for configuring NetFlow Reliable Export With SCTP

          NetFlow Reliable Export With SCTP

          Tasks for configuring NetFlow Layer 2 and Security Monitoring Exports

          "NetFlow Layer 2 and Security Monitoring Exports"

          Tasks for configuring the SNMP NetFlow MIB

          "Configuring SNMP and using the NetFlow MIB to Monitor NetFlow Data"

          Tasks for configuring the NetFlow MIB and Top Talkers feature

          "Configuring NetFlow Top Talkers using Cisco IOS CLI Commands or SNMP Commands"

          Information for installing, starting, and configuring the CNS NetFlow Collection Engine

          "Cisco CNS NetFlow Collection Engine Documentation"

          Standards

          Standards

          Title

          There are no new or modified standards associated with this feature

          --

          MIBs

          MIBs

          MIBs Link

          There are no new or modified MIBs associated with this feature.

          To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

          http:/​/​www.cisco.com/​go/​mibs

          RFCs

          RFCs

          Title

          There are no new or modified RFCs associated with this feature.

          --

          Technical Assistance

          Description

          Link

          The Cisco Technical Support website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.

          http:/​/​www.cisco.com/​techsupport

          Feature Information for Detecting and Analyzing Network Threats With NetFlow

          The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

          Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

          Table 11 Feature Information for NetFlow Layer 2 and Security Monitoring Exports

          Feature Name

          Releases

          Feature Configuration Information

          NetFlow Layer 2 and Security Monitoring Exports

          12.3(14)T

          The NetFlow Layer 2 and Security Monitoring Exports feature enables the capture of values from fields in Layer 3 and Layer 2 of IP traffic for accounting and security analysis.

          The following commands were modified by this feature: ip flow-capture, ip flow-export and show ip cache verbose flow.

          Support for capturing the value from the fragment offset field of IP headers added to NetFlow Layer 2 and Security Monitoring Exports1

          12.4(2)T

          The fragment-offset keyword for the ip flow-capture command enables capturing the value of the IP fragment offset field from the first fragmented IP datagram in a flow.

          NetFlow Top Talkers

          12.3(11)T,

          12.2(25)S

          This document references the Top Talkers feature from the NetFlow MIB and Top Talkers feature documentation.

          Top Talkers uses NetFlow functionality to obtain information regarding heaviest traffic patterns and most-used applications in the network.

          The following commands were introduced by this feature: cache-timeout, ip flow-top-talkers, match, show ip flow top-talkers, sort-by, and top.

          NetFlow Dynamic Top Talkers CLI

          12.4(4)T

          The NetFlow Dynamic Top Talkers CLI allows you to se an overview of the traffic characteristics on your router by aggregating flows based on the fields such as source IP address, destination prefix, and so forth.

          NetFlow Input Filters

          12.3(4)T, 12.2(25)S

          This document references the NetFlow Input Filters feature from the NetFlow Filtering and Sampling feature documentation.

          Random Sampled NetFlow

          12.3(4)T, 12.2(18)S, 12.0(26)S

          This document references the Random Sampled NetFlow feature from the NetFlow Filtering and Sampling feature documentation.

          1 This is a minor enhancement. Minor enhancements are not typically listed in Feature Navigator.

          Glossary

          data flowset --A collection of data records that are grouped in an export packet.

          export packet --A type of packet built by a device (for example, a router) with NetFlow services enabled. The packet is addressed to another device (for example, the NetFlow Collection Engine). The packet contains NetFlow statistics. The other device processes the packet (parses, aggregates, and stores information about IP flows).

          flow --A set of packets with the same source IP address, destination IP address, protocol, source/destination ports, and type-of-service, and the same interface on which flow is monitored. Ingress flows are associated with the input interface, and egress flows are associated with the output interface.

          flowset --A collection of flow records that follow the packet header in an export packet. A flowset contains information that must be parsed and interpreted by the NetFlow Collection Engine. There are two types of flowsets: template flowsets and data flowsets. An export packet contains one or more flowsets, and both template and data flowsets can be mixed in the same export packet.

          NetFlow --Cisco IOS accounting feature that maintains per-flow information.

          NetFlow Aggregation --A NetFlow feature that lets you summarize NetFlow export data on an IOS router before the data is exported to a NetFlow data collection system such as the NetFlow Collection Engine. This feature lowers bandwidth requirements for NetFlow export data and reduces platform requirements for NetFlow data collection devices.

          NetFlow Collection Engine (formerly NetFlow FlowCollector)--Cisco application that is used with NetFlow on Cisco routers and Catalyst series switches. The NetFlow Collection Engine collects packets from the router that is running NetFlow and decodes, aggregates, and stores them. You can generate reports on various aggregations that can be set up on the NetFlow Collection Engine.

          NetFlow v9 --NetFlow export format Version 9. A flexible and extensible means of carrying NetFlow records from a network node to a collector. NetFlow Version 9 has definable record types and is self-describing for easier NetFlow Collection Engine configuration.

          template --Describes the layout of a data flowset.

          template flowset --A collection of template records that are grouped in an export packet.


          Detecting and Analyzing Network Threats With NetFlow

          Contents

          Detecting and Analyzing Network Threats With NetFlow

          This document contains information about and instructions for detecting and analyzing network threats such as denial of service attacks (DoS) through the use of the following NetFlow features:

          • NetFlow Layer 2 and Security Monitoring Exports--This feature improves your ability to detect and analyze network threats such as denial of service attacks (DoS) by adding 9 fields that NetFlow can capture the values from.A few examples are:
            • IP Time-to-Live field
            • Packet length field
            • ICMP type and code fields
          • NetFlow Dynamic Top Talkers CLI--This feature gives you an overview of the highest volume traffic in your network by aggregating flows on a common field. For example, you can aggregate all of the flows for a destination network by aggregating them on the destination prefix. There are over 20 fields from flows that you can aggregate the highest volume traffic on. A few examples are:
            • Source or destination IP address
            • Source or destination prefix
            • Source or destination port
            • ICMP type and code
          • NetFlow Top Talkers--This feature gives you a more detailed view of the traffic in your network than the NetFlow Dynamic Top Talkers CLI feature because it looks at individual flows. You use the NetFlow Dynamic Top Talkers CLI feature to quickly identify high volume traffic of interest. You use the NetFlow Top Talkers feature to obtain more detailed information on each of the flows in the high volume traffic.

          • NetFlow Input Filters--This feature tracks a specific subset of NetFlow traffic for the purpose of class-based traffic analysis and monitoring. This feature is used in conjunction with the Top Talkers feature to help you focus your analysis on the traffic that might be a network threat such as a DoS attack.

          • Random Sampled NetFlow--This feature is typically used for statistical sampling of network traffic for traffic engineering or capacity planning purposes. It is used in the context of monitoring and analyzing network threats because it can be used to reduce the impact on the router using NetFlow to monitor traffic that might be a network threat, such as a DoS attack.

          Finding Feature Information

          Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

          Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

          Prerequisites for Detecting and Analyzing Network Threats With NetFlow

          Before you can use NetFlow for detecting and analyzing network threats you need to understand NetFlow and how to configure your router to capture IP traffic status and statistics using NetFlow. See the Cisco IOS NetFlow Overview and Configuring NetFlow and NetFlow Data Export modules for more details.

          NetFlow and Cisco Express Forwarding (CEF) or distributed CEF (dCEF) must be configured on your system before you enable NetFlow.

          Information About Detecting and Analyzing Network Threats With NetFlow

          NetFlow Layer 2 and Security Monitoring

          The Layer 2 and Layer 3 fields supported by the NetFlow Layer 2 and Security Monitoring Exports feature increase the amount of information that can be obtained by NetFlow about the traffic in your network. You can use the network traffic information for applications such as traffic engineering and usage-based billing.

          Layer 3 fields captured by the NetFlow Layer 2 and Security Monitoring Exports feature improve the capabilities of NetFlow for identifying DoS attacks. Layer 2 IP header fields help identify the path that the DoS attack is taking through the network.

          Layer 2 and Layer 3 fields are not key fields. They provide additional information about the traffic in an existing flow. Changes in the values of NetFlow key fields, such as the source IP address, from one packet to the next packet results in the creation of a new flow. For example, if the first packet captured by NetFlow has a source IP address of 10.34.0.2 and the second packet captured has a source IP address of 172.16.213.65, NetFlow will create two separate flows.

          Most DoS attacks consist of an attacker sending the same type of IP datagram repeatedly, in an attempt to overwhelm target systems. In such cases, the incoming traffic often has similar characteristics, such as the same values in each datagram for one or more fields that the NetFlow Layer 2 and Security Monitoring Exports feature can capture.

          The originator of DoS attacks cannot be easily identified because the IP source address of the device sending the traffic is usually forged. However, you can easily trace the traffic back through the network to the router on which it is arriving by using the NetFlow Layer 2 and Security Monitoring Exports feature to capture the MAC address and VLAN-ID fields. If the router on which traffic is arriving supports NetFlow, you can configure the NetFlow Layer 2 and Security Monitoring Exports feature on it to identify the interface on which the traffic is arriving. The figure below shows an example of an attack in progress.

          Figure 1. DoS Attack Arriving over the Internet


          Note


          You can analyze the data captured by NetFlow directly from the router by using the show ip cache verbose flow command or by the Cisco Network Services (CNS) NetFlow Collector Engine.


          Once you have concluded that a DoS attack is taking place by analyzing the Layer 3 fields in the NetFlow flows, you can analyze the Layer 2 fields in the flows to discover the path that the DoS attack is taking through the network.

          An analysis of the data captured by the NetFlow Layer 2 and Security Monitoring Exports feature, for the scenario shown in the above figure, indicates that the DoS attack is arriving on Router C, because the upstream MAC address is from the interface that connects Router C to Switch A. It is also evident that there are no routers between the target host (the e-mail server) and the NetFlow router, because the destination MAC address of the DoS traffic that the NetFlow router is forwarding to the e-mail server is the MAC address of the e-mail server.

          You can learn the MAC address that Host C is using to send traffic to Router C by configuring the NetFlow Layer 2 and Security Monitoring Exports feature on Router C. The source MAC address will be from Host C. The destination MAC address will be for the interface on the NetFlow router.

          Once you know the MAC address that Host C is using and the interface on Router C on which Host C’s DoS attack is arriving, you can mitigate the attack by reconfiguring Router C to block Host C’s traffic. If Host C is on a dedicated interface, you can disable the interface. If Host C is using an interface that carries traffic from other users, you must configure your firewall to block Host C’s traffic, but still allow the traffic from the other users to flow through Router C.

          Layer 3 Information Capture Using NetFlow Layer 2 and Security Monitoring Exports

          The five fields that the NetFlow Layer 2 and Security Monitoring Exports feature captures from Layer 3 IP traffic in a flow are the following:

          • Internet Control Message Protocol (ICMP) type and code

          • ID field

          • Fragment offset

          • Packet length field

          • Time-to-live field

          Figure 5 shows the fields in an IP packet header.

          Figure 2. IP Packet Header Fields

          Table 4 describes the header fields in Figure 5.

          Table 1 IP Packet Header Fields

          Field

          Description

          Version

          The version of the IP protocol. If this field is set to 4, it is an IPv4 datagram. If this field is set to 6, it is an IPv6 datagram.

          Note   

          IPv4 and IPv6 headers have different structures.

          IHL (Internet Header Length)

          Internet Header Length is the length of the Internet header in 32-bit word format and thus points to the beginning of the data.

          Note   

          The minimum value for the correct header length is 5.

          ToS

          Type of service (ToS) provides an indication of the abstract parameters of the quality of service desired. These parameters are to be used to guide the selection of the actual service parameters when a networking device transmits a datagram through a particular network.

          Total Length

          Total length is the length of the datagram, measured in octets, including Internet header and data.

          Identification (ID)

          The value in the ID field is entered by the sender. All the fragments of an IP datagram have the same value in the ID field. Subsequent IP datagrams from the same sender will have different values in the ID field.

          Frequently, a host receives fragmented IP datagrams from several senders concurrently. Also, frequently a host receives multiple IP datagrams from the same sender concurrently.

          The value in the ID field is used by the destination host to ensure that the fragments of an IP datagram are assigned to the same packet buffer during the IP datagram reassembly process. The unique value in the ID field is used to prevent the receiving host from mixing together IP datagram fragments of different IP datagrams from the same sender during the IP datagram reassembly process.

          Flags

          A sequence of three bits is used to set and track IP datagram fragmentation parameters. The bits are:

          • 001—The IP datagram can be fragmented. More fragments of the current IP datagram are in transit.

          • 000—The IP datagram can be fragmented. This is the last fragment of the current IP datagram.

          • 010—The IP datagram cannot be fragmented. This is the entire IP datagram.

          Fragment Offset

          This field indicates where in the datagram this fragment belongs.

          TTL (Time-to-Live)

          This field indicates the maximum time the datagram is allowed to remain in the Internet system. If this field contains the value 0, then the datagram must be destroyed. This field is modified in Internet header processing. The TTL is measured in units of seconds, but because every module that processes a datagram must decrease the TTL by at least 1 even if it processes the datagram in less than a second, the TTL must be thought of only as an upper bound on the time a datagram can exist. The intention is to discard undeliverable datagrams and bound the maximum datagram lifetime.

          Protocol

          Indicates the type of transport packet included in the data portion of the IP datagram. Common values are:

          • 1—ICMP

          • 6—TCP

          • 17—UDP

          Header checksum

          A checksum on the header only. Because some header fields, such as the TTL field, change every time an IP datagram is forwarded, this value is recomputed and verified at each point that the Internet header is processed.

          Source IP Address

          IP address of the sending station.

          Destination IP Address

          IP address of the destination station.

          Options and Padding

          The options and padding may appear in datagrams. If they do appear, they must be implemented by all IP modules (host and gateways). Options and padding are always implemented in any particular datagram; transmissions are not.

          Figure 6 shows the fields in an ICMP datagram.

          Figure 3. ICMP Datagram

          Table 5 interprets the packet format in the figure seen above. ICMP datagrams are carried in the data area of an IP datagram, after the IP header.

          Table 2 ICMP Packet Format

          Type

          Name

          Codes

          0

          Echo reply

          0—None.

          1

          Unassigned

          2

          Unassigned

          3

          Destination unreachable

          0—Network unreachable.

          1—Host unreachable.

          2—Protocol unreachable.

          3—Port unreachable.

          4—Fragmentation needed and don't fragment (DF) bit set.

          5—Source route failed.

          6—Destination network unknown.

          7—Destination host unknown.

          8—Source host isolated.

          9—Communication with the destination network is administratively prohibited.

          10—Communication with the destination host is administratively prohibited.

          11—Destination network unreachable for ToS.

          12—Destination host unreachable for ToS.

          4

          Source quench

          0—None.

          5

          Redirect

          0—None.

          0—Redirect datagram for the network.

          1—Redirect datagram for the host.

          2—Redirect datagram for the ToS and network.

          3—Redirect datagram for the ToS and host.

          6

          Alternate host address

          0—Alternate address for the host.

          7

          Unassigned

          8

          Echo

          0—None.

          9

          Router advertisement

          0—None.

          10

          Router selection

          0—None.

          11

          Time exceeded

          0—Time to live exceeded in transit.

          12

          Parameter problem

          0—Pointer indicates the error.

          1—Missing a required option.

          2—Inappropriate length.

          13

          Timestamp

          0—None.

          14

          Timestamp reply

          0—None.

          15

          Information request

          0—None.

          16

          Information reply

          0—None.

          17

          Address mask request

          0—None.

          18

          Address mask reply

          0—None.

          19

          Reserved (for security)

          20–29

          Reserved (for robustness experiment)

          30

          Trace route

          31

          Datagram conversion error

          32

          Mobile host redirect

          33

          IPv6 where-are-you

          34

          IPv6 I-am-here

          35

          Mobile registration request

          36

          Mobile registration reply

          37–255

          Reserved

          Layer 2 Information Capture Using NetFlow Layer 2 and Security Monitoring Exports

          The NetFlow Layer 2 and Security Monitoring Exports feature can capture the values of the MAC address and VLAN ID fields from flows. The two supported VLAN types are 802.1q and the Cisco Inter-Switch Link (ISL) protocol.

          Layer 2 MAC Address Fields

          The Layer 2 fields for which the NetFlow Layer 2 and Security Monitoring Exports feature captures the values are as follows:

          • The source MAC address field from frames that are received by the NetFlow router.

          • The destination MAC address field from frames that are transmitted by the NetFlow router.

          • The VLAN ID field from frames that are received by the NetFlow router.

          • The VLAN ID field from frames that are transmitted by the NetFlow router.

          Figure 2 shows the Ethernet Type II and Ethernet 802.3 frame formats. The destination address field and the source address field in the frame formats are the MAC address values that are captured by NetFlow.

          Figure 4. Ethernet Type II and 802.3 Frame Formats

          Table 1 explains the fields for the Ethernet frame formats.

          Table 3 Ethernet Type II and 802.3 Frame Fields

          Field

          Description

          Preamble

          The entry in the Preamble field is an alternating pattern of 0s and 1s that communicates to receiving stations about an incoming frame. It also provides a means for the receiving stations to synchronize their clocks with the incoming bit stream.

          SOF (Start of frame)

          The SOF field holds an alternating pattern of 0s and 1s, ending with two consecutive 1s, indicating that the next bit is the first bit of the first byte of the destination MAC address.

          Destination Address

          The 48-bit destination address identifies which station on the LAN should receive the frame. The first two bits of the destination MAC address are reserved for the following special functions:

          • The first bit in the destination address field indicates whether the address is an individual address (0) or a group address (1).

          • The second bit indicates whether the destination address is globally administered (0) or locally administered (1).

          The remaining 46 bits form a uniquely assigned value that identifies a single station, a defined group of stations, or all stations on the network.

          Source Address

          The 48-bit source address identifies which station transmitted the frame. The source address is always an individual address, and the leftmost bit in the Source Address field is always 0.

          Type

          or

          Length

          Type—In an Ethernet Type II frame, a part of the frame is used for the Type field. The Type field is used to identify the next layer protocol in the frame.

          Length—In an 802.3 Ethernet frame, a part of the frame is used for the Length field. The Length field is used to indicate the length of the Ethernet frame. The value can be from 46 to 1500 bytes.

          Data

          or

          802.2 header and data

          Ethernet Type II—46 to 1500 bytes of data

          or

          802.3/802.2—8 bytes of header and 38 to 1492 bytes of data.

          FCS (Frame Check Sequence)

          This field contains a 32-bit cyclic redundancy check (CRC) value, which is created by the sending station and is recalculated by the receiving station, to check for damaged frames. The FCS is generated for the destination address, source address, Type, and Data fields of the frame. The FCS does not include the data portion of the frame.

          Layer 2 VLAN ID Fields

          NetFlow can capture the value in the VLAN ID field for 802.1q tagged VLANs and Cisco ISL encapsulated VLANs. This section describes the two types of VLANs, 802.1q and ISL.


          Note


          ISL and 802.1q are commonly called VLAN encapsulation protocols.


          Understanding 802.1q VLANs

          Devices that use 802.1q insert a four-byte tag into the original frame before it is transmitted. Figure 3 shows the format of an 802.1q tagged Ethernet frame.

          Figure 5. 802.1q Tagged Ethernet Type II or 802.3 Frame

          Table 2 describes the fields for 802.1q VLANs.

          Table 4 802.1q VLAN Encapsulation Fields

          Field

          Description

          Destination Address

          The 48-bit destination address identifies which stations on the LAN should receive the frame. The first two bits of the destination MAC address are reserved for the following special functions:

          • The first bit in the destination address field indicates whether the address is an individual address (0) or a group address (1).

          • The second bit indicates whether the destination address is globally administered (0) or locally administered (1).

          The remaining 46 bits form a uniquely assigned value that identifies a single station, a defined group of stations, or all stations on the network.

          Source Address

          The 48-bit source address identifies which station transmitted the frame. The source address is always an individual address, and the leftmost bit in the Source Address field is always 0.

          Type

          or

          Length

          Type—In an Ethernet Type II frame, a part of the frame is used for the Type field. The Type field is used to identify the next layer protocol in the frame.

          Length—In an 802.3 Ethernet frame, a part of the frame is used for the Length field. The Length field is used to indicate the length of the Ethernet frame. The value can be from 46 to 1500 bytes.

          Data

          or

          802.2 header and data

          Ethernet Type II—46 to 1500 bytes of data

          or

          802.3/802.2—8 bytes of header and 38 to 1492 bytes of data.

          FCS (Frame Check Sequence)

          This field contains a 32-bit cyclic redundancy check (CRC) value, which is created by the sending station and is recalculated by the receiving station, to check for damaged frames. The FCS is generated for the destination address, source address, Type, and Data fields of the frame. The FCS does not include the data portion of the frame.

          Tag Protocol ID (TPID)

          This 16-bit field is set to a value of 0x8100 to identify the frame as an IEEE 802.1q tagged frame.

          Priority

          This 3-bit field refers to the 802.1p priority. It is also known as user priority. It indicates the frame priority level used for prioritizing traffic and can represent levels 0–7.

          Tag Control Information

          This 2-byte Tag Control Information field consists of the following two subfields:

          • Canonical Format Indentifier (CFI)—If the value of this 1-bit field is 1, the MAC address is in noncanonical format. If the value of this field is 0, the MAC address is in canonical format.

          • VLAN ID—This 12-bit field uniquely identifies the VLAN to which the frame belongs. It can have a value from 0 to 4095.

          Cisco ISL VLANs

          ISL is a Cisco-proprietary protocol for encapsulating frames on a VLAN trunk. Devices that use ISL add an ISL header to the frame. This process is known as VLAN encapsulation. 802.1Q is the IEEE standard for tagging frames on a VLAN trunk. Figure 4 shows the format of a Cisco ISL-encapsulated Ethernet frame.

          Figure 6. Cisco ISL Tagged Ethernet Frame

          Table 3 describes the fields for 802.1q VLANs.

          Table 5 ISL VLAN Encapsulation

          Field

          Description

          DA (destination address)

          This 40-bit field is a multicast address and is set at 0n01-00-0c-00-00 or 0n03-00-0c-00-00. The receiving host determines that the frame is encapsulated in ISL by reading the 40-bit DA field and matching it with one of the two ISL multicast addresses.

          TYPE

          This 4-bit field indicates the type of frame that is encapsulated and to indicate alternative encapsulations.

          TYPE codes:

          • 0000—Ethernet

          • 0001—Token Ring

          • 0010—FDDI

          • 0011—ATM

          USER

          This 4-bit field is used to extend the meaning of the Frame TYPE field. The default USER field value is 0000. For Ethernet frames, the USER field bits 0 and 1 indicate the priority of the packet as it passes through the switch. Whenever traffic can be handled more quickly, the packets with this bit set should take advantage of the quicker path. However, such paths are not required.

          USER codes:

          • xx00—Normal priority

          • xx01—Priority 1

          • xx10—Priority 2

          • xx11—Highest priority

          SA

          This 48-bit field is the source address field of the ISL packet. It should be set to the 802.3 MAC address of the switch port transmitting the frame. The receiving device can ignore the SA field of the frame.

          LEN

          This 16-bit value field stores the actual packet size of the original packet. The LEN field represents the length of the packet in bytes, excluding the DA, TYPE, USER, SA, LEN, and FCS fields. The total length of the excluded fields is 18 bytes, so the LEN field represents the total length minus 18 bytes.

          AAAA03(SNAP)

          The AAAA03 Subnetwork Access Protocol (SNAP) field is a 24-bit constant value of 0xAAAA03.

          HSA

          This 24-bit field represents the upper three bytes (the manufacturer’s ID portion) of the SA field. It must contain the value 0x00-00-0C.

          VLAN

          This 15-bit field is the virtual LAN ID of the packet. This value is used to mark frames on different VLANs.

          BPDU

          The bit in the bridge protocol data unit (BPDU) field is set for all BPDU packets that are encapsulated by the ISL frame. The BPDUs are used by the spanning tree algorithm to learn information about the topology of the network. This bit is also set for Cisco Discovery Protocol and VLAN Trunk Protocol (VTP) frames that are encapsulated.

          INDEX

          This 16-bit field indicates the port index of the source of the packet as it exits the switch. It is used for diagnostic purposes only, and may be set to any value by other devices. It is ignored in received packets.

          RES

          This 16-bit field is used when Token Ring or FDDI packets are encapsulated with an ISL frame.

          Encapsulated FRAME

          This field contains the encapsulated Layer 2 frame.

          FCS

          The FCS field consists of 4 bytes. It includes a 32-bit CRC value, which is created by the sending station and is recalculated by the receiving station, to check for damaged frames. The FCS covers the DA, SA, Length/Type, and Data fields. When an ISL header is attached to a Layer 2 frame, a new FCS is calculated over the entire ISL packet and added to the end of the frame.

          Note   

          The addition of the new FCS does not alter the original FCS that is contained within the encapsulated frame.

          NetFlow Top Talkers

          The usual implementation of NetFlow exports NetFlow data to a collector. The NetFlow Top Talkers features can be used for security monitoring or accounting purposes for top talkers, and matching and identifying key traffic in your network. These features are also useful for a network location where a traditional NetFlow export operation is not possible. The NetFlow Top Talkers features do not require a collector to obtain information regarding flows. Instead, the NetFlow data is displayed on the router when the NetFlow Dynamic Top Talkers CLI show ip flow top command, or the NetFlow Top Talkers show ip flow top-talkersis used.

          Comparison of the NetFlow Dynamic Top Talkers CLI and NetFlow Top Talkers Features

          There are two very similar NetFlow features that can be used for monitoring the highest volume traffic in your network. The feature names are:

          NetFlow Dynamic Top Talkers CLI

          This feature was introduced in 12.4(4)T. The NetFlow Dynamic Top Talkers CLI feature is used to obtain an overview of the highest volume traffic (top talkers) in your network. It provides an overview of the traffic by aggregating the flows in the cache based on the aggregation field that you select when you use the NetFlow Dynamic Top Talkers CLI feature.

          The NetFlow Dynamic Top Talkers CLI feature does not require modifications to the configuration of the router. The show ip flow top command is the only command that you need to use for the NetFlow Dynamic Top Talkers CLI feature. You can invoke any of the NetFlow Dynamic Top Talkers CLI options directly from the show ip flow top command whenever you need them.


          Note


          The information that you want to use the NetFlow Dynamic Top Talkers CLI feature to analyze must be available in the cache. For example, if you want to be able to identify the MAC address in the flows, you must configure the ip flow-capture mac-addresses command in order to capture the values from the MAC address fields in the traffic first.


          The NetFlow Dynamic Top Talkers CLI feature aggregates flows and allows them to be sorted so that they can be viewed. The flows can be aggregated on fields in the cache such as source or destination IP address, ICMP type and code values, and so forth. For a full list of the fields that you can aggregate the flows on, refer to the show ip flow topcommand in the Cisco IOS NetFlow command reference documentation.

          The aggregated top talker flows can be sorted by any of the following criteria:

          • The aggregated field in the display data

          • The number of bytes in the display data

          • The number of flows in the display data

          • The by number of packets in the display data

          • In ascending or descending order (to find the least used Top talker)

          In addition to sorting top talkers, you can further organize your output by specifying criteria that the top talkers must match, such as source or destination IP address or port. The match keyword is used to specify this criterion. For a full list of the matching criterion that you can select, refer to the show ip flow topcommand in the Cisco IOS NetFlow command reference documentation.

          The NetFlow Dynamic Top Talkers CLI feature can help you quickly identify traffic that is associated with security threats such as DoS attacks because it does not require configuration modifications. You can change the NetFlow Dynamic Top Talkers CLI options for identifying and analyzing network threats in the aggregated flows on-the-fly as you learn more about the traffic that is of interest. For example, after you have identified that there is a lot of ICMP traffic in your network by using the show ip flow top 10 aggregate icmp command you can learn what IP networks the traffic is being sent to by using the show ip flow top 10 aggregate icmp match destination-prefix 172.0.0.0/8 command.


          Note


          A high volume of ICMP traffic might indicate that an ICMP-based DoS attack is in progress.


          The show ip flow top command:

          • Does not require additional NetFlow configuration commands to display top talkers. Therefore you do not need to supply the configuration mode password to the administrators who use the he show ip flow top command to monitor network traffic. The only prerequisite for using the show ip flow top command is that you have configured NetFlow on at least one interface on the router.

          • Aggregates flows automatically based on the aggregation method that you select, and independently of any netflow aggregation cache(s).

          • Allows you to change the parameters of the command, such as the number of flows to display, the display order, and match criterion, on-the-fly every time that you use the command without having to change the router’s configuration.

          • Allows you to sort the display output in ascending or descending order based on:
            • The aggregated field
            • The number of bytes
            • The number of flows,
            • The number of packets
          show ip flow top and show ip cache verbose flow

          Many of the values shown in the display output of the show ip cache verbose flow command are in hexadecimal. If you want to match these values using the show ip flow top command with the match keyword, you must enter the field value that you want to match in hexadecimal. For example, to match on the destination port of 00DC in the following except from the show ip cache verbose flow command, you would use the match destination-port 0x00DC keywords and argument for the show ip flow top command.

          SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs  Pkts
          Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
          Et0/0.1        10.10.11.4      Et1/0.1        172.16.10.8     06 00  00     209 
          00DC /0  0                     00DC
           /0  0     0.0.0.0                40   281.4
          MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
          Min plen:       40                            Max plen:        40
          Min TTL:        59                            Max TTL:         59
          IP id:           0
          Match Criteria with the show ip flow top command

          You can limit the top talkers that are displayed by the show ip flow top command by using the match keyword and arguments. For example, you can display the IP destination address top talkers that have a prefix of 224.0.0.0 using the show ip flow top 10 aggregate destination-address match destination-prefix 224.0.0.0/3 command.

          For a full list of the matching criterion that you can select, refer to the show ip flow topcommand in the Cisco IOS NetFlow Command Reference . If you do not configure match criteria all of the flows are considered as candidates for aggregation as top talkers based on the volume of traffic they represent.

          The Order That Aggregation Occurs in

          With the exception of the flows keyword, all matches are performed prior to aggregation, and only matching flows are aggregated. For example, the show ip flow top5aggregate destination-address match destination-prefix 172.16.0.0/16 command analyzes all of the available flows looking for any flows that have destination addresses that match the destination-prefix value of 172.16.0.0/16. If it finds any matches it aggregates them, and then displays the number of aggregated destination-address flows that is equal to the number of top talkers that were requested in the command-in this case five.

          The flows keyword matches the number of aggregated flows post-aggregation. For example, the show ip flow top 2 aggregate destination-address match 6 command aggregates all of the flows on the values in their destination IP address field, and then displays the top talkers that have 6 aggregated flows.

          Number of Flows Matched

          If you do not specify match criteria and there is traffic in the flows that includes the field that you used to aggregate the flows on, all of the flows will match. For example, if your router has 20 flows with IP traffic and you enter the show ip flow top 10 aggregate destination-address command the display will indicate that 20 of 20 flows matched, and the 10 top talkers will be displayed.

          If you use the match keyword to limit the flows that are aggregated to the flows with a destination prefix of 224.0.0.0/3, and only one flow matches this criterion the output will indicate that one out of six flows matched. For example, if your router has 6 flows with IP traffic, but only one of them has a destination prefix of 224.0.0.0/3, and you enter the show ip flow top 10 aggregate destination-address match destination-prefix 224.0.0.0/3 command, the display will indicate that 1 of 6 flows matched.

          If the total number of top talkers is less than the number of top talkers that were requested in the command, the total number of top talkers is displayed. For example, if you enter a value of five for the number of top talkers to display and there are only three top talkers that match the criteria that you used, the display will only include three top talkers.

          When a match criterion is included with the show ip flow top command, the display output will indicate "N of M flows matched" where N <= M, N = matched flows, and M = total flows seen. The numbers of flows seen could potentially be more than the total number of flows in the cache if some of the analyzed flows were removed from the cache and new flows were created ahead of the current point, as the top talkers feature sweeps through the cache. Therefore, M is NOT the total number of flows in the cache, but rather, the number of observed flows.

          If you attempt to display the top talkers by aggregating them on a field that is not in the cache you will see the "% aggregation-field" is not available for this cache" message. For example, if you use the show ip flow top 5 aggregate s ource-vlan command, and you have not enabled the capture of VLAN IDs from the flows, you will see the "% VLAN id is not available for this cache" message.

          NetFlow Top Talkers

          This feature was introduced in 12.3(11)T. NetFlow Top Talkers is used to obtain information about individual flows in the cache. It does not aggregate the flows like the NetFlow Dynamic Top Talkers CLI feature.

          The NetFlow Top Talkers feature compares all of the flows and displays information about each of the flows that have the heaviest traffic volumes (top talkers). The show ip flow top-talkerscommand requires you to pre-configure the router using the NetFlow Top Talkers configuration commands:

          • ip flow-top-talkers --Enters the NetFlow Top Talkers configuration mode.

          • sort-by --Selects the sort order for the flows in the display output.
            • bytes--Sort the flows based on the numbers of bytes in each flow.
            • packets--Sort the flows based on the numbers of packets in each flow.
          • top --Specifies the number of top talkers to monitor.

          • match (optional)--Specifies additional criteria, such as IP addresses, port numbers, and so forth, that must be matched in the flow to qualify as a candidate for top talker status.

          For a full list of the matching criterion that you can select, refer to the ip flow top-talkerscommand in the Cisco IOS NetFlow Command Reference . If you do not configure match criteria all of the flows are considered as candidates as top talkers based on the volume of traffic they represent.

          • show ip flow top talkers [verbose]--Displays the flows.

          For more information on the NetFlow Top Talkers feature, refer to Configuring NetFlow Top Talkers using Cisco IOS CLI Commands or SNMP Commands.

          Filtering and Sampling of NetFlow Traffic

          NetFlow provides highly granular per-flow traffic statistics in a Cisco router. A flow is a unidirectional stream of packets that arrive at the router on the same subinterface, have the same source and destination IP addresses, Layer 4 protocol, TCP/UDP source and destination ports, and the same ToS (type of service) byte in the IP headers. The router accumulates NetFlow statistics in a NetFlow cache and can export them to an external device (such as the Cisco Networking Services (CNS) NetFlow Collection Engine) for further processing.

          Full NetFlow accounts for all traffic entering the subinterface on which it is enabled. But in some cases, you might gather NetFlow data on only a subset of this traffic. The Random Sampled NetFlow feature and the NetFlow Input Filters feature each provide ways to limit incoming traffic to only traffic of interest for NetFlow processing. Random Sampled NetFlow provides NetFlow data for a subset of traffic in a Cisco router by processing only one randomly selected packet out of n sequential packets. The NetFlow Input Filters feature provides the capability to gather NetFlow data on only a specific user-defined subset of traffic.


          Note


          Random Sampled NetFlow is more statistically accurate than Sampled NetFlow. NetFlow's ability to sample packets was first provided by a feature named Sampled NetFlow. The methodology that the Sampled NetFlow feature uses is deterministic sampling, which selects every nth packet for NetFlow processing on a per-interface basis. For example, if you set the sampling rate to 1 out of 100 packets, then Sampled NetFlow samples the 1st, 101st, 201st, 301st, and so on packets. Sampled NetFlow does not allow random sampling and thus can make statistics inaccurate when traffic arrives in fixed patterns.



          Note


          The Random Sampled NetFlow algorithms are applied after input filtering.


          The table below compares the NetFlow Input Filters feature and the NetFlow Random Sampled feature.

          Table 6 Comparison of the NetFlow Input Filters Feature and the Random Sampled NetFlow Feature

          Comparison Category

          NetFlow Input Filters Feature

          Random Sampled NetFlow Feature

          Brief description

          This feature enables you to gather NetFlow data on only a specific subset of traffic. You do this by creating filters to select flows for NetFlow processing. For example, you can select flows from a specific group of hosts. This feature also lets you select various sampling rates for selected flows.

          This feature provides NetFlow data for a subset of traffic in a Cisco router by processing only one randomly selected packet out of n sequential packets (n is a user-configurable parameter). Packets are sampled as they arrive (before any NetFlow cache entries are made for those packets).

          Main uses

          You can use this feature for class-based traffic analysis and monitoring on-network or off-network traffic.

          This feature is also useful if you have too much traffic and you want to limit the traffic that is analyzed.

          You can use this feature for traffic engineering, capacity planning, and applications where full NetFlow is not needed for an accurate view of network traffic.

          This feature is also useful if you have too much traffic and you want to limit the traffic that is analyzed.

          Export format support

          This feature is supported in the Version 5 and Version 9 NetFlow export formats.

          This feature is supported in the Version 5 and Version 9 NetFlow export formats.

          Cisco IOS release support

          12.3(4)T.

          12.3(2)T, 12.2(18)S, and 12.0(26)S.

          Subinterface support

          You can configure NetFlow Input Filters per subinterface as well as per physical interface.

          You can select more than one filter per subinterface and have all of the filters run simultaneously.

          You can configure the Random Sampled NetFlow feature per subinterface as well as per physical interface.

          You can not run Full NetFlow and Random Sampled NetFlow concurrently on the same subinterface. You must disable full NetFlow on the subinterface before Random Sampled NetFlow will take effect.

          Traffic is collected only on the subinterfaces on which Random Sampled NetFlow is configured. As with full NetFlow, enabling Random Sampled NetFlow on a physical interface does not enable Random Sampled NetFlow on subinterfaces automatically--you must explicitly configure it on the subinterfaces.

          Memory impact

          This feature requires no additional memory. It allows you to use a smaller NetFlow cache than full NetFlow, because it significantly reduces the number of flows. This feature requires an insignificant amount of memory for each configured NetFlow filter.

          This feature can create a smaller NetFlow cache than full NetFlow if by reducing the number of packets being analyzed the numbers of flows in the cache is also reduced. This feature requires an insignificant amount of memory for each configured NetFlow sampler.

          Performance impact

          Accounting of classified traffic saves router resources by reducing the number of flows being processed and exported. The amount of bandwidth saved depends on the usage and the class-map criteria.

          However, performance might degrade depending on the number and complexity of class maps configured in a policy.

          Statistical traffic sampling substantially reduces consumption of router resources (especially CPU resources) while providing valuable NetFlow data.

          This feature substantially reduces the impact of NetFlow data export on interface traffic. For example, a sampling rate of 1 out of 100 packets reduces the export of NetFlow data by about 99% percent.

          NetFlow Input Filters Flow Classification

          For the NetFlow Input Filters feature, classification of packets can be based on any of the following: IP source and destination addresses, Layer 4 protocol and port numbers, incoming interface, MAC address, IP Precedence, DSCP value, Layer 2 information (such as Frame-Relay DE bits or Ethernet 802.1p bits), and Network-Based Application Recognition (NBAR) information. The packets are classified (filtered) on the above criteria, and flow accounting is applied to them on subinterfaces.

          The filtering mechanism uses the Modular QoS Command-Line Interface (MQC) to classify flows. You can create multiple filters with matching samplers on a per-subinterface basis. For example, you can subdivide subinterface traffic into multiple classes based on type of service (ToS) values or destination prefixes (or both). For each class, you can also configure sampling at a different rate, using higher rates for higher-priority classes of traffic and lower rates for lower-priority ones.

          MQC has many policies (actions) such as bandwidth rate and queuing management. These policies are applied only if a packet matches a criterion in a class map that is applied to the subinterface. A class map contains a set of match clauses and instructions on how to evaluate the clauses and acts as a filter for the policies, which are applied only if a packet’s content satisfies the match clause. The NetFlow Input Filters feature adds NetFlow accounting to the MQC infrastructure, which means that flow accounting is done on a packet only if it satisfies the match clauses.

          Two types of filter are available:

          • ACL-based flow-mask filters

          • Fields of filter (source IP address, destination IP address, source application port, destination application port, port protocol, ToS bits, and TCP flags)

          For more information on Modular QoS Command-Line Interface (MQC) refer to the Cisco IOS Quality of Service Solutions Configuration Guide .

          Random Sampled NetFlow Sampling Mode

          Sampling mode makes use of an algorithm that selects a subset of traffic for NetFlow processing. In the random sampling mode that the Random Sampled NetFlow feature uses, incoming packets are randomly selected on average one out of each n sequential packets is selected for NetFlow processing. For example, if you set the sampling rate to 1 out of 100 packets, then NetFlow might sample the 5th packet and then the 120th, 230th, 302nd, and so on. This sample configuration provides NetFlow data on 1 percent of total traffic. The n value is a parameter that you can configure from 1 to 65535 packets.

          Random Sampled NetFlow The NetFlow Sampler Map

          Random Sampled NetFlow is useful if you have too much traffic and you want to limit the traffic that is analyzed. A NetFlow sampler map is created with the flow-sampler-map sampler-map-name command. The sampling mode for the sampler map is configured with the mode random one-out-of sampling-rate command. The range of values for the sampling-rate argument is 1 to 65535. Each NetFlow sampler map can be applied to one or many subinterfaces as well as physical interfaces. The sampler map is applied to an interface or subinterface with the flow-sampler sampler-map-name command. You can define up to eight NetFlow sampler maps.

          How to Configure and Use NetFlow to Detect and Analyze Network Threats

          Using NetFlow to detect and analyze network threats requires a combination of configuration commands and show commands. You start by configuring the NetFlow Layer 2 and Security Monitoring Exports feature to capture values of the additional non-key fields from the flows so that they can be displayed in the cache by the NetFlow show commands. Capturing the values in the additional non-key fields is required so that you can identify the path the traffic is taking through the network and other characteristics of the traffic such as TTL values and packet length values.

          After you configure the NetFlow Layer 2 and Security Monitoring Exports feature, you use the NetFlow Dynamic Top Talkers CLI command to obtain an overview of the traffic flows the router is forwarding. The overview displays information such as the protocol distribution in the flows, the source ip addresses that are sending the flows, and the networks the flows are being sent to.

          After you identify the type of flows that you want to focus, on such as ICMP traffic, and other characteristics such as source IP addresses and destination network prefixes, you use the NetFlow Top Talkers feature to obtain more focused and detailed information on the individual flows. The NetFlow Top Talkers feature is configured with match criteria that focuses it on the types of traffic that you have identified. If your router is keeping track of several flows and you are only interested in analyzing a subset of them you, can configure NetFlow Input Filters to limit the flows that NetFlow is tracking.

          Prerequisites

          CEF or dCEF must be configured globally, and on the interface that you want to run NetFlow on, before you configure NetFlow Layer 2 and Security Monitoring Exports.

          You must have NetFlow enabled on at least one interface in the router before you configure NetFlow Layer 2 and Security Monitoring Exports.

          If you want to capture the values of the Layer 3 IP fragment offset field from the IP headers in your IP traffic using the ip flow-capture fragment-offset command, your router must be running Cisco IOS 12.4(2)T or later.

          This section contains the following procedures:

          Configuring NetFlow Layer 2 and Security Monitoring Exports

          Perform the following task to configure the NetFlow Layer 2 and Security Monitoring Exports feature.

          Before You Begin

          To export the data captured with the NetFlow Layer 2 and Security Monitoring feature, you must configure NetFlow to use the NetFlow Version 9 data export format.

          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    ip flow-capture fragment-offset

            4.    ip flow-capture icmp

            5.    ip flow-capture ip-id

            6.    ip flow-capture mac-addresses

            7.    ip flow-capture packet-length

            8.    ip flow-capture ttl

            9.    ip flow-capture vlan-id

            10.    interface type interface-type interface-number ]

            11.    ip flow ingress

            12.    end


          DETAILED STEPS
             Command or ActionPurpose
            Step 1 enable


            Example:
            Router> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.

             
            Step 2 configure terminal


            Example:
            Router# configure terminal
             

            Enters global configuration mode.

             
            Step 3 ip flow-capture fragment-offset


            Example:
            Router(config)# ip flow-capture fragment-offset
             

            Enables capturing the value of the IP fragment offset field from the first fragmented IP datagram in a flow.

             
            Step 4 ip flow-capture icmp


            Example:
            Router(config)# ip flow-capture icmp
             

            Enables you to capture the value of the ICMP type and code fields from the first ICMP datagram in a flow.

             
            Step 5 ip flow-capture ip-id


            Example:
            Router(config)# ip flow-capture ip-id
             

            Enables you to capture the value of the IP-ID field from the first IP datagram in a flow.

             
            Step 6 ip flow-capture mac-addresses


            Example:
            Router(config)# ip flow-capture mac-addresses
             

            Enables you to capture the values of the source and destination MAC addresses from the first Layer 2 frame in a flow.

             
            Step 7 ip flow-capture packet-length

            Example:
            Router(config)# ip flow-capture packet-length
             

            Enables you to capture the minimum and maximum values of the packet length field from IP datagrams in a flow.

             
            Step 8 ip flow-capture ttl


            Example:
            Router(config)# ip flow-capture ttl
             

            Enables you to capture the minimum and maximum values of the Time-to-Live (TTL) field from IP datagrams in a flow.

             
            Step 9 ip flow-capture vlan-id


            Example:
            Router(config)# ip flow-capture vlan-id
             

            Enables you to capture the 802.1q or ISL VLAN-ID field from first VLAN encapsulated Layer 2 frame in a flow that is received or transmitted on a trunk port.

             
            Step 10 interface type interface-type interface-number ]


            Example:
            Router(config)# interface ethernet 0/0
             

            Enters interface configuration mode for the type of interface specified in the command.

             
            Step 11 ip flow ingress


            Example:
            and/or


            Example:
            ip flow egress


            Example:
            Router(config-if)# ip flow ingress


            Example:
            and/or


            Example:
            Router(config-if)# ip flow egress
             

            Enables ingress NetFlow data collection on the interface.

            and/or

            Enables egress NetFlow data collection on the interface.

             
            Step 12 end

            Example:
            Router(config)# end
             

            Returns to privileged EXEC mode.

             

            Verifying NetFlow Layer 2 and Security Monitoring Exports

            This task verifies that NetFlow Layer 2 and Security Monitoring Exports is configured correctly. The show ip cache verbose flowcommand gives a detailed view of the status and statistics for flows in the NetFlow main cache. The values for the NetFlow non-key fields that you have configured with the NetFlow Layer 2 and Security Monitoring Exports feature are included for each flow.

            To see the values of the fields that you have configured the NetFlow Layer 2 and Security Monitoring Exports feature to capture, your router must be forwarding IP traffic that meets the criteria for these fields. For example, if you configure the ip flow-capture vlan-id command, your router must be forwarding IP datagrams over interfaces that are configured as VLAN trunks to capture the VLAN-ID values from the layer-two frames carrying the IP datagrams in the flow.

            Restrictions

            Displaying Detailed NetFlow Cache Information on Platforms Running Distributed Cisco Express Forwarding

            On platforms running dCEF, NetFlow cache information is maintained on each line card or Versatile Interface Processor. If you want to use the show ip cache verbose flow command to display this information on a distributed platform, you must enter the command at a line card prompt.

            Cisco 7500 Series Platform

            To display detailed NetFlow cache information on a Cisco 7500 series router that is running distributed dCEF, enter the following sequence of commands:

            Router# if-con
             
            slot-number
            LC-
            slot-number
            # show ip cache verbose
             flow
            

            For Cisco IOS Releases 12.3(4)T, 12.3(6), and 12.2(20)S and later, enter the following command to display detailed NetFlow cache information:

            Router# execute-on 
            slot-number 
            show ip cache verbose
             flow
             

            Cisco 12000 Series Platform

            To display detailed NetFlow cache information on a Cisco 12000 Series Internet Router, enter the following sequence of commands:

            Router# attach
             
            slot-number
            LC-
            slot-number
            # show ip cache verbose
             flow
            

            For Cisco IOS Releases 12.3(4)T, 12.3(6), and 12.2(20)S and later, enter the following command to display detailed NetFlow cache information:

            Router# execute-on slot-number show ip cache verbose flow

            To verify the configuration of NetFlow Layer 2 and Security Monitoring Exports use the following step.

            SUMMARY STEPS

              1.    show ip cache verbose flow


            DETAILED STEPS
            show ip cache verbose flow

            This example shows that NetFlow Layer 2 and Security Monitoring Exports is working properly because the values have been captured from the non-key Layer 3 and Layer 2 fields in the flows. The values captured in the flows are shown in bold text.



            Example:
            Router# show ip cache verbose flow
            IP packet size distribution (33978 total packets):
            1-32   64   96  128  160  192  224  256  288  320  352  384  416  448  480
            .856 .143 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
            512  544  576 1024 1536 2048 2560 3072 3584 4096 4608
            .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
            IP Flow Switching Cache, 278544 bytes
            14 active, 4082 inactive, 59 added
            12452 ager polls, 0 flow alloc failures
            Active flows timeout in 10 minutes
            Inactive flows timeout in 15 seconds
            IP Sub Flow Cache, 25736 bytes
            28 active, 996 inactive, 148 added, 59 added to flow
            0 alloc failures, 0 force free
            1 chunk, 1 chunk added
            last clearing of statistics never
            Protocol         Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)
            --------         Flows     /Sec     /Flow  /Pkt     /Sec     /Flow     /Flow
            TCP-SMTP             2      0.0      1730    40      3.6     600.7       0.2
            UDP-other           31      0.0         1    54      0.0       3.6      16.8
            ICMP                12      0.0      1728    28     22.0     600.1       0.1
            Total:              45      0.0       538    29     25.7     189.2      11.6
            SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs  Pkts
            Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
            .
            .
            .
            Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  10     696
            0000 /0  0                     0C01 /0  0     0.0.0.0                28   241.4
            MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
            Min plen:       28                            Max plen:        28
            Min TTL:        59                            Max TTL:         59
            ICMP type:      12                            ICMP code:        1
            IP id:           0
            

            Using NetFlow Dynamic Top Talkers CLI to Display the Protocol Distribution

            You can obtain a quick overview of the traffic in your network by viewing the protocol distribution. Use this task to display the top talkers (aggregated flows) for these three IPv4 protocol types:

            • 1--ICMP

            • 6--TCP

            • 17--UDP

            SUMMARY STEPS

              1.    show ip flow top number aggregate aggregate-field sorted-by packets descending


            DETAILED STEPS
            show ip flow top number aggregate aggregate-field sorted-by packets descending

            The following example looks for up to three top talkers, aggregates them on the protocol field, sorts them by packets, and displays the output in descending order:



            Example:
            Router# show ip flow top 3 aggregate protocol sorted-by packets descending
             
            There are 3 top talkers:
            IPV4 PROT       bytes        pkts       flows
            =========  ==========  ==========  ==========
                    1      406196       14507          12
                    6       96560        2414           2
                   17          52           1           1
            15 of 15 flows matched.
            

            The table below describes the significant fields shown in the display output.

            Table 7 show ip flow top 3 aggregate protocol sorted-by packets descending Field Descriptions

            Field

            Description

            There are 3 top talkers

            The number of top talkers is displayed.

            IPV4 PROT

            This position in the display output is used to show the field that you selected to aggregate the flows on.

            The protocol keyword aggregates IPv4 traffic in the flows based on the IPv4 protocol type. In this example there are three IPv4 protocol types in the flows:

            • 1--ICMP

            • 6--TCP

            • 17--UDP

            bytes

            Displays the numbers of bytes in the aggregated flows for each top talker.

            pkts

            Displays the numbers of packets in the aggregated flows for each top talker.

            flows

            Displays the numbers of aggregated flows for each top talker.

            15 of 15 flows matched.

            Displays the number of flows that matched the command.

            All 15 flows in the router are aggregated into three top talkers. In this example all of the flow traffic is top talker traffic.

            The majority of the traffic is ICMP traffic (IP protocol type 1). This might indicate an ICMP DoS attack is in progress.


            Using NetFlow Dynamic Top Talkers CLI to Display the Source IP Address Top Talkers Sending ICMP Traffic

            The display output from the show ip flow top 10 aggregate protocol sorted-by packets descending used in Using NetFlow Dynamic Top Talkers CLI to Display the Protocol Distribution section indicates that there is a possible ICMP-based DoS attack in progress. The next step to take is to identify the flows that are sending the ICMP traffic. In this case the flows will be aggregated on the source IP addresses.

            SUMMARY STEPS

              1.    show ip flow top number aggregate aggregate-field sorted-by packets match match-field match-value


            DETAILED STEPS
            show ip flow top number aggregate aggregate-field sorted-by packets match match-field match-value

            The following command looks for up to 20 top talkers, aggregates them on the source IP address, sorts them by packets, and matches on the protocol icmp:



            Example:
            Router# show ip flow top 20 aggregate source-address sorted-by packets match protocol icmp
            There are 6 top talkers:
            IPV4 SRC-ADDR         bytes        pkts       flows
            ===============  ==========  ==========  ==========
            10.132.221.111        90440        3230           1
            10.10.12.1            90440        3230           1
            10.251.138.218        90440        3230           1
            10.71.200.138         90384        3228           1
            10.231.185.254        90384        3228           1
            10.106.1.1            90356        3227           1
            6 of 15 flows matched.
            Router
            

            The table below describes the significant fields shown in the display.

            Table 8 show ip flow top 20 aggregate source-address sorted-by packets match protocol icmp Field Descriptions

            Field

            Description

            There are 6 top talkers

            The number of top talkers is displayed.

            Note   

            Only 6 top talkers are displayed, even though you asked for 20, because only 6 of the 15 flows in the cache matched the criteria you specified. The number 20 is an upper limit that will be applied in the event that there are over 20 top talkers.

            IPV4 SRC-ADDR

            This position in the display output is used to show the field that you selected to aggregate the flows on.

            The source-addresskeyword aggregates flows based on the source IP address. In this example there are 6 IP source addresses with aggregated flows. Each of the IP addresses has 1 flow, therefore no aggregation was performed:

            • 10.132.221.111

            • 10.10.12.1

            • 10.251.138.218

            • 10.71.200.138

            • 10.231.185.254

            • 10.106.1.1

            bytes

            Displays the numbers of bytes in the aggregated flows for each top talker.

            pkts

            Displays the numbers of packets in the aggregated flows for each top talker.

            flows

            Displays the numbers of aggregated flows for each top talker.

            6 of 15flows matched.

            Displays the number of flows that matched the command.

            The ICMP traffic is aggregated into six top talkers (source IP addresses). Each top talker has one flow. No aggregation is performed on this traffic because there is a 1-to-1 correlation of IP source addresses and flows.


            Using NetFlow Dynamic Top Talkers CLI to Display the Destination IP Address Top Talkers Receiving ICMP Traffic

            The display output from the show ip flow top 5 aggregate source-address sorted-by packets match protocol icmp command used in Using NetFlow Dynamic Top Talkers CLI to Display the Source IP Address Top Talkers Sending ICMP Traffic section showed the six top talkers (IP source addresses) that are sending the 12 ICMP traffic flows. The next step to take is to identify the flows that are the target of the ICMP traffic. In this case the flows will be aggregated on the destination IP addresses.

            SUMMARY STEPS

              1.    show ip flow top number aggregate aggregate-field sorted-by packets match match-field match-value


            DETAILED STEPS
            show ip flow top number aggregate aggregate-field sorted-by packets match match-field match-value

            The following command looks for up to 20 top talkers, aggregates them on the destination IP address, sorts them by packets, and matches on the protocol icmp



            Example:
            Router# show ip flow top 20 aggregate destination-address sorted-by packets match protocol icmp
            There is 1 top talker:
            IPV4 DST-ADDR         bytes        pkts       flows
            ===============  ==========  ==========  ==========
            172.16.10.2          407456       14552           6
            6 of 14 flows matched.
            Router
            

            The table below describes the significant fields shown in the display.

            Table 9 show ip flow top 20 aggregate destination-address sorted-by packets match protocol icmp Field Descriptions

            Field

            Description

            There is 1 top talker

            The number of top talkers is displayed.

            • The ICMP traffic is aggregated into 6 flows for one destination IP addresses.

            IPV4 DST-ADDR

            This position in the display output is used to show the field that you selected to aggregate the flows on.

            The destination-addresskeyword aggregates flows based on the destination IP address. In this example there are 3 IP destination address with aggregated flows. The IP addresses has 8 aggregated flows:

            • 172.16.10.2

            bytes

            Displays the numbers of bytes in the aggregated flows for each top talker.

            pkts

            Displays the numbers of packets in the aggregated flows for each top talker.

            flows

            Displays the numbers of aggregated flows for each top talker.

            6 of 14 flows matched.

            Displays the number of flows that matched the command.

            The previous task identified six ICMP top talkers based on source IP addresses that each had one flow. This task identified that there is one ICMP top talker based on destination IP addresses that is the target for 6 individual flows. There is a 1-to-1 correlation between the number of ICMP flows in the top talkers aggregated on the source IP address and the number of ICMP flows in the top talkers aggregated on the destination IP address. There is a high probability that an ICMP-based DoS attack on the host with the IP address of 172.16.10.2 is in progress.


            Configuring NetFlow Top Talkers to Monitor Network Threats

            The previous task (Using NetFlow Dynamic Top Talkers CLI to Display the Destination IP Address Top Talkers Receiving ICMP Traffic) identified a probable ICMP-based DoS attack on the host with the IP address 172.16.10.2. This task uses the NetFlow Top Talkers feature to configure the router to monitor the DoS attack by tracking the individual ICMP flows. After you have configured the NetFlow Top Talkers feature to focus on the DoS attack traffic, you can use the show ip flow top-talkers verbose command to identify the path the DoS traffic is taking through the network.

            Perform the following task to configure the NetFlow Top Talkers feature.

            SUMMARY STEPS

              1.    enable

              2.    configure terminal

              3.    ip flow-top-talkers

              4.    match destination address ip-address /prefix-mask

              5.    top number

              6.    sort-by [bytes | packets

              7.    end


            DETAILED STEPS
               Command or ActionPurpose
              Step 1 enable


              Example:
              Router> enable
               

              Enables privileged EXEC mode.

              • Enter your password if prompted.

               
              Step 2 configure terminal


              Example:
              Router# configure terminal
               

              Enters global configuration mode.

               
              Step 3 ip flow-top-talkers


              Example:
              Router(config)# ip flow-top-talkers
              
               

              Enters NetFlow top talkers configuration mode.

               
              Step 4 match destination address ip-address /prefix-mask


              Example:
              Router(config-flow-top-talkers)
              # match destination address 172.16.10.2/32
              
               

              Specifies the destination IP addresses to match.

               
              Step 5 top number


              Example:
              Router(config-flow-top-talkers)# top 50
               

              Specifies the maximum number of top talkers that will be retrieved by a NetFlow top talkers query.

               
              Step 6 sort-by [bytes | packets


              Example:
              Router(config-flow-top-talkers)# sort-by packets
               

              Specifies the sort criterion for the top talkers.

              • The top talkers can be sorted either by the total number of packets of each top talker or the total number of bytes of each top talker.

               
              Step 7 end


              Example:
              Router(config-flow-top-talkers)# end
               

              Exits to privileged EXEC mode.

               

              Monitoring and Analyzing the NetFlow Top Talkers Flows

              To monitor and analyze the NetFlow Top Talkers flows, use the following step.

              SUMMARY STEPS

                1.    show ip flow top-talkers verbose


              DETAILED STEPS
              show ip flow top-talkers verbose

              The following sample shows details for the six traffic flows that are being sent to the host with IP address 172.16.10.2.



              Example:
              Router# show ip flow top-talkers verbose
              SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs Bytes
              Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
              Et0/0.1        10.106.1.1      Et1/0.1        172.16.10.2     01 00  10    9408 
              0000 /0  0                     0800 /0  0     0.0.0.0                28   116.3
              MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
              Min plen:       28                            Max plen:        28
              Min TTL:        59                            Max TTL:         59
              ICMP type:       8                            ICMP code:        0
              IP id:           0
              Et0/0.1        10.132.221.111  Et1/0.1        172.16.10.2     01 00  10    9408 
              0000 /0  0                     0800 /0  0     0.0.0.0                28   116.4
              MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
              Min plen:       28                            Max plen:        28
              Min TTL:        59                            Max TTL:         59
              ICMP type:       8                            ICMP code:        0
              IP id:           0
              Et0/0.1        10.10.12.1      Et1/0.1        172.16.10.2     01 00  10    9408 
              0000 /0  0                     0C01 /0  0     0.0.0.0                28   116.4
              MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
              Min plen:       28                            Max plen:        28
              Min TTL:        59                            Max TTL:         59
              ICMP type:      12                            ICMP code:        1
              IP id:           0
              Et0/0.1        10.251.138.218  Et1/0.1        172.16.10.2     01 00  10    9408 
              0000 /0  0                     0C01 /0  0     0.0.0.0                28   116.4
              MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
              Min plen:       28                            Max plen:        28
              Min TTL:        59                            Max TTL:         59
              ICMP type:      12                            ICMP code:        1
              IP id:           0
              Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  10    9408 
              0000 /0  0                     0C01 /0  0     0.0.0.0                28   116.5
              MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
              Min plen:       28                            Max plen:        28
              Min TTL:        59                            Max TTL:         59
              ICMP type:      12                            ICMP code:        1
              IP id:           0
              Et0/0.1        10.231.185.254  Et1/0.1        172.16.10.2     01 00  10    9408 
              0000 /0  0                     0C01 /0  0     0.0.0.0                28   116.5
              MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
              Min plen:       28                            Max plen:        28
              Min TTL:        59                            Max TTL:         59
              ICMP type:      12                            ICMP code:        1
              IP id:           0
              6 of 50 top talkers shown. 6 of 8 flows matched.
              
              Note   

              Only six of the eight flows matched because the rest of the flows are not top talker flows.

              Note   

              The top 50 flows were requested, however there are only eight flows in the cache.

              This display output contains the information required for determining the path that the DoS attack traffic is taking through the network. This information will be used to react to the DoS attack by adding security measures such as access-lists to the affected interfaces. The table below describes the significant fields in the display from the show ip flow top-talkers verbose command for determining the network path the DoS traffic is taking.
              Table 10 Significant Field Descriptions for show ip flow top-talkers verbose

              Field

              Description

              SrcIf

              Interface on which the packet was received.

              • All of the ICMP DoS traffic is being received on Et0/0.1

              SrcIPaddress

              This is the source IP address of the traffic in the six top talkers. The traffic is using 6 different IP source addresses

              • 10.132.221.111

              • 10.10.12.1

              • 10.251.138.218

              • 10.71.200.138

              • 10.231.185.254

              • 10.106.1.1

              DstIf

              Interface from which the packet was transmitted.

              • All of the ICMP DoS traffic is being transmitted over Et1/0.1

              Note   

              If an asterisk (*) immediately follows the DstIf field, the flow being shown is an egress flow.

              ICMP Type

              The ICMP datagram types

              • 8--Echo

              • 12--Parameter Problem

              ICMP Code

              The ICMP codes

              • 0--None (not applicable)

              • 1--Depends on the ICMP Type
                • A code value of 1 for ICMP type 12 indicates that a required option is missing

              DstIPaddress

              This is the destination IP address of the traffic.

              Note   

              172.17.10.2 is the IP address that is being attacked.

              MAC

              These are the source and destination MAC addresses from the traffic. The source and destination MAC address are read from left to right in the output.

              • The traffic is being received from MAC address aaa.bbb.cc03.

              Note   

              This MAC address is interface 1/0.1 on router R2.

              • The traffic is being transmitted to MAC address aaa.bbb.cc06.

              Note   

              This MAC address is interface 1/0.1 on router R4.

              VLAN id

              These are the source and destination VLAN IDs. The source and destination VLAN IDs are read from left to right in the output.

              • The traffic is being received from VLAN 5.

              • The traffic is being transmitted to VLAN 6.

              The flows in this example show only the ICMP DoS attack traffic that is destined for the host with IP address 172.16.10.2. These flows were created specifically for documenting this task. In a real network, the host under attack might be communicating with other hosts that are using legitimate applications such as e-mail and web sites. In this case, the Top Talkers match filter on the destination IP address (match destination address 172.16.10.2/32) that was configured in the Configuring NetFlow Top Talkers to Monitor Network Threats will not limit the display of the show ip flow top-talkers command to the ICMP DoS attack traffic.
              Note   

              For more information on the fields in the display output of the show ip cache verbose flow command, refer to the Cisco IOS NetFlow Command Reference .

              If you are using the Top Talkers feature to analyze a network threat and you are not able to use the basic match filters to limit the display of the show ip flow top-talkers command to the traffic that you are analyzing, you can use NetFlow filtering and sampling to limit the traffic that shows up in the display of the show ip flow top-talkers command. The process for configuring NetFlow filtering and sampling is explained in the Configuring NetFlow Filtering and Sampling.

              Configuring NetFlow Filtering and Sampling

              If you use the show ip cache flow command or the show ip cache verbose flow command to display the flows in the cache, you will see the ICMP flows that are selected by NetFlow filtering and sampling on interface Ethernet0/0.1, and flows for all NetFlow supported traffic types on any other interfaces that NetFlow is running on. The show ip flow top-talkers [verbose] command is used to display the flow status and statistics for the traffic type you configured with the match criteria over interfaces to which you applied the service policy. For example, in this case you configured top talkers to match on ICMP traffic sent from any host that is arriving on Ethernet0/0.1 and destined for 172.16.10.2.

              In this task the Top Talkers feature is being used more as a flow filter to separate flows of interest from all of the flows the router is seeing, rather than a filter to display the flows with the highest traffic volumes. Top talkers is used in this manner because in this example all of the ICMP DoS attack flows are of interest, not just the flows with the highest volumes. This is why a large value is assigned to the top keyword in the top talkers configuration. Setting the value for the top keyword to 50 when the largest number of ICMP DoS attack flows tracked by the router is 12 ensures that all of the ICMP DoS attack flows will be tracked.

              If your router sees a significant number of flows involved in a DoS attack, you might want to set the value for the top keyword to a number that is less than the total number of flows to limit the number of flows that you see in the display when you use the show ip flow top-talkerscommand. This will ensure that you are seeing the flows that have the highest volume of DoS attack traffic. However, if all of the flows have the same traffic volume, the show ip flow top-talkerscommand will not be able to differentiate between them. It displays the number of flows that you set the value of the top keyword to, starting from the first flow in the cache.

              Perform the following task to configure NetFlow Filtering and sampling.


              Note


              Restrictions for NetFlow Input Filters

              On Cisco 7500 platforms, the NetFlow Input Filters feature is supported only in distributed mode.

              Restrictions for Random Sampled NetFlow

              If full NetFlow is enabled on an interface, it takes precedence over Random Sampled NetFlow (which will thus have no effect). Disable full NetFlow on an interface before enabling Random Sampled NetFlow on that interface.

              Enabling Random Sampled NetFlow on a physical interface does not automatically enable Random Sampled NetFlow on subinterfaces; you must explicitly configure it on subinterfaces. Also, disabling Random Sampled NetFlow on a physical interface (or a subinterface) does not enable full NetFlow. This restriction prevents the transition to full NetFlow from overwhelming the physical interface (or subinterface). If you want full NetFlow, you must explicitly enable it.

              You must use NetFlow Version 9 if you want to use sampler option templates or view NetFlow sampler IDs.


              SUMMARY STEPS

                1.    enable

                2.    configure terminal

                3.    flow-sampler-map sampler-map-name

                4.    mode random one-out-of packet-interval

                5.    exit

                6.    class-map class-map-name [match-all | match-any]

                7.    match access-group access-group

                8.    exit

                9.    policy-map policy-map-name

                10.    class { class-name | class-default}

                11.    netflow-sampler sampler-map-name

                12.    exit

                13.    exit

                14.    interface interface-type interface-number [.subinterface number]

                15.    no [ip route-cache flow | ip flow ingress]

                16.    service-policy {input | output} policy-map-name

                17.    exit

                18.    ip flow-top-talkers

                19.    top number

                20.    sort-by packets

                21.    match class-map claas-name

                22.    no match destination address ip-address /prefix-mask

                23.    exit

                24.    access-list access-list-number permit icmp source destination

                25.    end


              DETAILED STEPS
                 Command or ActionPurpose
                Step 1 enable


                Example:
                Router> enable
                 

                Enables privileged EXEC mode.

                • Enter your password if prompted.

                 
                Step 2 configure terminal


                Example:
                Router# configure terminal
                 

                Enters global configuration mode.

                 
                Step 3 flow-sampler-map sampler-map-name


                Example:
                Router(config)# flow-sampler-map icmp-dos-fs-map
                 

                Defines a statistical sampling NetFlow export flow sampler map.

                • The sampler-map-name argument is the name of the flow sampler map to be defined.

                Entering the flow-sampler-map command enables the flow sampler configuration mode.

                 
                Step 4 mode random one-out-of packet-interval


                Example:
                Router(config-sampler-map)# mode random one-out-of 2
                 

                Specifies a statistical sampling NetFlow export random sampling mode and a packet interval.

                • The random keyword specifies that sampling uses the random sampling mode.

                • The one-out-of packet-interval argument-keyword pair specifies the packet interval (one out of every npackets) from which to sample. For n, you can specify from 1 to 65535 (packets).

                 
                Step 5 exit


                Example:
                Router(config-sampler-map)# exit
                 

                Exits back to global configuration mode.

                 
                Step 6 class-map class-map-name [match-all | match-any]


                Example:
                Router(config)# class-map match-any icmp-dos-class-map
                 

                Creates a class map to be used for matching packets to a specified class.

                • The class-map-name argument is the name of the class for the class map. The name can be a maximum of 40 alphanumeric characters. The class name is used for both the class map and for configuring policy for the class in the policy map.

                • The match-all | match-anykeywords determine how packets are evaluated when multiple match criteria exist. Packets must either meet all of the match criteria (match-all) or only one of the match criteria (match-any) to be considered a member of the class.

                Entering the class-mapcommand enables class-map configuration mode, in which you can enter one of the match commands to configure the match criteria for this class.

                 
                Step 7 match access-group access-group


                Example:
                Router(config-cmap)# match access-group 101
                 

                Configures the match criteria for a class map on the basis of the specified access control list (ACL).

                • The access-group argument is a numbered ACL whose contents are used as the match criteria against which packets are checked to determine if they belong to this class. An ACL number can be a number from 1 to 2699.

                 
                Step 8 exit


                Example:
                Router(config-cmap)# exit
                 

                Exits back to global configuration mode.

                 
                Step 9 policy-map policy-map-name


                Example:
                Router(config)# policy-map icmp-dos-policy-map
                 

                Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy.

                • The policy-map-name argument is the name of the policy map. The name can be a maximum of 40 alphanumeric characters.

                Entering the policy-mapcommand enables quality of service (QoS) policy-map configuration mode, in which you can configure or modify the class policies for that policy map

                 
                Step 10 class { class-name | class-default}


                Example:
                Router(config-pmap)# class icmp-dos-class-map
                 

                Specifies the name of the class whose policy you want to create or change or specifies the default class (commonly known as the class-default class) before you configure its policy.

                • The class-name argument is the name of the class for which you want to configure or modify policy.

                • The class-default keyword specifies the default class so that you can configure or modify its policy.

                Entering the class command enables QoS policy-map class configuration mode.

                 
                Step 11 netflow-sampler sampler-map-name


                Example:
                Router(config-pmap-c)# netflow-sampler icmp-dos-fs-map
                 

                Enables a NetFlow input filter sampler.

                • The sampler-map-name argument is the name of the NetFlow sampler map to apply to the class.

                You can assign only one NetFlow input filter sampler to a class. Assigning another NetFlow input filter sampler to a class overwrites the previous one.

                 
                Step 12 exit


                Example:
                Router(config-pmap-c)# exit
                 

                Exits back to policy-map configuration mode.

                 
                Step 13 exit


                Example:
                Router(config-pmap# exit
                 

                Exits back to global configuration mode.

                 
                Step 14 interface interface-type interface-number [.subinterface number]


                Example:
                Router(config)# interface Ethernet0/0.1
                 

                Specifies the interface and enters subinterface configuration mode.

                • The interface-type argument is the type of interface to be configured.

                • The interface-numberargument is the number of the interface. Refer to the appropriate hardware manual for slot and port information.

                 
                Step 15 no [ip route-cache flow | ip flow ingress]


                Example:
                Router(config-subif)# no ip flow ingress
                 

                Removes the existing NetFlow command from the interface.

                Note   

                NetFlow sampling and filtering can not start if there is another command on the interface that is enabling NetFlow.

                 
                Step 16 service-policy {input | output} policy-map-name


                Example:
                Router(config-subif)# service-policy input icmp-dos-policy-map
                 

                Attaches a policy map to an input interface or virtual circuit (VC), or an output interface or VC, to be used as the service policy for that interface or VC.

                • The input keyword attaches the specified policy map to the input interface or input VC.

                • The output keyword attaches the specified policy map to the output interface or output VC.

                • The policy-map-name is the name of a service policy map (created through use of the policy-map command) to be attached. The name can be a maximum of 40 alphanumeric characters.

                 
                Step 17 exit


                Example:
                Router(config-subif)# exit
                 

                Exits back to global configuration mode.

                 
                Step 18 ip flow-top-talkers


                Example:
                Router(config)# ip flow-top-talkers
                 

                Enters NetFlow top talkers configuration mode.

                 
                Step 19 top number


                Example:
                Router(config-flow-top-talkers)# top 50
                 

                Specifies the maximum number of top talkers that will be retrieved by a NetFlow top talkers query.

                 
                Step 20 sort-by packets


                Example:
                Router(config-flow-top-talkers)# sort-by packets
                 

                Specifies the sort criterion for the top talkers.

                • The top talkers can be sorted either by the total number of packets of each top talker or the total number of bytes of each top talker.

                 
                Step 21 match class-map claas-name


                Example:
                Router(config-flow-top-talkers)# match class-map icmp-dos-class-map
                 

                Specifies that the match criteria should be obtained from the class-map.

                 
                Step 22 no match destination address ip-address /prefix-mask


                Example:
                Router(config-flow-top-talkers)# no match destination address 172.16.10.2/32
                 

                (Optional) If you still have a match entry for the destination address you should remove it so that only the class-name match criteria is used.

                 
                Step 23 exit


                Example:
                Router(config-sampler-map)# exit
                 

                Exits back to global configuration mode.

                 
                Step 24 access-list access-list-number permit icmp source destination


                Example:
                Router(config)# access-list 101 permit icmp any host 172.16.10.2
                 

                Creates an extended access list that is used to track any host that is sending ICMP traffic to 172.16.10.2.

                 
                Step 25 end


                Example:
                Router(config)# end
                 

                Exits to privileged EXEC mode.

                 

                Verify NetFlow Filtering and Sampling

                To verify that filtering and sampling is working properly, use the following step.

                SUMMARY STEPS

                  1.    show flow-sampler


                DETAILED STEPS
                show flow-sampler

                Any non-zero value in the display output below indicates that Filtering and sampling is active.



                Example:
                Router# show flow-sampler
                 
                Sampler : icmp-dos-fs-map, id : 1, packets matched : 63226, mode : random sampling mode
                  sampling interval is : 2
                Router

                Monitoring and Analyzing the Sampled and Filtered NetFlow Top Talkers Flows

                To monitor and analyze the filtered and sampled NetFlow top talkers flows use the following step.

                SUMMARY STEPS

                  1.    show ip flow top-talkers

                  2.    show ip flow top-talkers verbose


                DETAILED STEPS
                  Step 1   show ip flow top-talkers

                  The following sample output shows the six traffic flows that are being sent to the host with IP address 172.16.10.2.



                  Example:
                  Router# show ip flow top-talkers
                  SrcIf         SrcIPaddress    DstIf         DstIPaddress    Pr SrcP DstP Bytes
                  Et0/0.1       10.231.185.254  Et1/0.1       172.16.10.2     01 0000 0C01  5460 
                  Et0/0.1       10.106.1.1      Et1/0.1       172.16.10.2     01 0000 0800  5124 
                  Et0/0.1       10.132.221.111  Et1/0.1       172.16.10.2     01 0000 0800  5012 
                  Et0/0.1       10.251.138.218  Et1/0.1       172.16.10.2     01 0000 0C01  4844 
                  Et0/0.1       10.10.12.1      Et1/0.1       172.16.10.2     01 0000 0C01  4704 
                  Et0/0.1       10.71.200.138   Et1/0.1       172.16.10.2     01 0000 0C01  4396 
                  6 of 50 top talkers shown. 6 of 7 flows matched.
                  
                  Step 2   show ip flow top-talkers verbose

                  The following sample output below shows the details for the six traffic flows that are being sent to the host with IP address 172.16.10.2.



                  Example:
                  Router# show ip flow top-talkers verbose
                   
                  SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs Bytes
                  Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
                  Et0/0.1        10.106.1.1      Et1/0.1        172.16.10.2     01 00  10    2884 
                  0000 /0  0                     0800 /0  0     0.0.0.0                28    64.6
                  Sampler: 1  Class: 1  
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       28                            Max plen:        28
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       8                            ICMP code:        0
                  IP id:           0
                  Et0/0.1        10.132.221.111  Et1/0.1        172.16.10.2     01 00  10    2828 
                  0000 /0  0                     0800 /0  0     0.0.0.0                28    64.6
                  Sampler: 1  Class: 1  
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       28                            Max plen:        28
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       8                            ICMP code:        0
                  IP id:           0
                  Et0/0.1        10.231.185.254  Et1/0.1        172.16.10.2     01 00  10    2716 
                  0000 /0  0                     0C01 /0  0     0.0.0.0                28    64.6
                  Sampler: 1  Class: 1  
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       28                            Max plen:        28
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:      12                            ICMP code:        1
                  IP id:           0
                  Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  10    2548 
                  0000 /0  0                     0C01 /0  0     0.0.0.0                28    58.0
                  Sampler: 1  Class: 1  
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       28                            Max plen:        28
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:      12                            ICMP code:        1
                  IP id:           0
                  Et0/0.1        10.251.138.218  Et1/0.1        172.16.10.2     01 00  10    2436 
                  0000 /0  0                     0C01 /0  0     0.0.0.0                28    64.6
                  Sampler: 1  Class: 1  
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       28                            Max plen:        28
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:      12                            ICMP code:        1
                  IP id:           0
                  Et0/0.1        10.10.12.1      Et1/0.1        172.16.10.2     01 00  10    2352 
                  0000 /0  0                     0C01 /0  0     0.0.0.0                28    57.7
                  Sampler: 1  Class: 1  
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       28                            Max plen:        28
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:      12                            ICMP code:        1
                  IP id:           0
                  6 of 50 top talkers shown. 6 of 7 flows matched.
                  

                  Configuration Examples for Detecting and Analyzing Network Threats With NetFlow

                  Configuring NetFlow Layer 2 and Sec Mon Exports to Capture Traffic From a Simulated FTP Attack Example

                  The following example shows how to use the NetFlow Layer 2 and Security Monitoring Exports feature to find out whether your network is being attacked by a host that is sending fake FTP traffic in an attempt to overwhelm the FTP server. This attack might cause end users to see a degradation in the ability of the FTP server to accept new connections or to service existing connections.

                  This example uses the network shown in the figure below. Host A is sending fake FTP packets to the FTP server.

                  This example also shows you how to use the Layer 2 data captured by the NetFlow Layer 2 and Security Monitoring Exports feature to learn where the traffic is originating and what path it is taking through the network.

                  Figure 7. Test Network


                  Tip


                  Keep track of the MAC addresses and IP addresses of the devices in your network. You can use them to analyze attacks and to resolve problems.



                  Note


                  This example does not include the ip flow-capture icmpcommand that captures the value of the ICMP type and code fields. The use of the ip flow-capture icmp command is described in "Configuring NetFlow Layer 2 and Sec Mon Exports to Capture Traffic From a Simulated ICMP Attack Example."


                  R2

                  !
                  hostname R2
                  !
                  interface Ethernet0/0
                   mac-address aaaa.bbbb.cc02
                   ip address 172.16.1.2 255.255.255.0
                  !
                  interface Ethernet1/0
                   mac-address aaaa.bbbb.cc03
                   no ip address
                  !
                  interface Ethernet1/0.1
                   encapsulation dot1Q 5
                   ip address 172.16.6.1 255.255.255.0
                  !
                  !
                  router rip
                   version 2
                   network 172.16.0.0
                   no auto-summary
                  !

                  R3

                  !
                  hostname R3
                  !
                  ip flow-capture fragment-offset
                  ip flow-capture packet-length
                  ip flow-capture ttl
                  ip flow-capture vlan-id
                  ip flow-capture ip-id
                  ip flow-capture mac-addresses
                  !
                  interface Ethernet0/0
                   mac-address aaaa.bbbb.cc04
                   no ip address
                  !
                  interface Ethernet0/0.1
                   encapsulation dot1Q 5
                   ip address 172.16.6.2 255.255.255.0
                   ip accounting output-packets
                   ip flow ingress
                  !
                  interface Ethernet1/0
                   mac-address aaaa.bbbb.cc05
                   no ip address
                  !
                  interface Ethernet1/0.1
                   encapsulation dot1Q 6
                   ip address 172.16.7.1 255.255.255.0
                   ip accounting output-packets
                   ip flow egress
                  !
                  router rip
                   version 2
                   network 172.16.0.0
                   no auto-summary
                  !

                  R4

                  !
                  hostname R4
                  !
                  interface Ethernet0/0
                   mac-address aaaa.bbbb.cc07
                   ip address 172.16.10.1 255.255.255.0
                  !
                  interface Ethernet1/0
                   mac-address aaaa.bbbb.cc06
                   no ip address
                  !
                  interface Ethernet1/0.1
                   encapsulation dot1Q 6
                   ip address 172.16.7.2 255.255.255.0
                  !
                  router rip
                   version 2
                   network 172.16.0.0
                   no auto-summary
                  !
                  

                  Analyze an FTP DoS Attack Using the show ip cache verbose flow command Example

                  The show ip cache verbose flow command displays the NetFlow flows. You can use this display output to identify the path that the FTP traffic from Host A is taking as it is received and transmitted by R3.


                  Note


                  To reduce the space required to display the output from the show ip flow cache verbose flowcommand only the FTP flows are shown.



                  Tip


                  Look for the flows that have FTP in them and make a note of the interfaces, MAC addresses, and VLANs (if applicable) for the flows.


                  R3# show ip cache verbose flow
                   
                  IP packet size distribution (189118 total packets):
                     1-32   64   96  128  160  192  224  256  288  320  352  384  416  448  480
                     .043 .610 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
                      512  544  576 1024 1536 2048 2560 3072 3584 4096 4608
                     .000 .000 .173 .000 .173 .000 .000 .000 .000 .000 .000
                  IP Flow Switching Cache, 278544 bytes
                    25 active, 4071 inactive, 615 added
                    263794 ager polls, 0 flow alloc failures
                    Active flows timeout in 30 minutes
                    Inactive flows timeout in 15 seconds
                  IP Sub Flow Cache, 25736 bytes
                    50 active, 974 inactive, 1648 added, 615 added to flow
                    0 alloc failures, 0 force free
                    1 chunk, 1 chunk added
                    last clearing of statistics never
                  Protocol         Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)
                  --------         Flows     /Sec     /Flow  /Pkt     /Sec     /Flow     /Flow
                  TCP-FTP             12      0.0       895    40      0.9    1363.8       5.5
                  TCP-FTPD            12      0.0       895    40      0.9    1363.8       5.6
                  Total:             590      0.0       317   383     16.1     430.1      12.4
                  Et0/0.1        192.168.87.200  Et1/0.1        172.16.10.2     06 00  00      63 
                  0015 /0  0                     0015
                   /0  0     0.0.0.0                40    94.5
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       40                            Max plen:        40
                  Min TTL:        59                            Max TTL:         59
                  IP id:           0
                  Et0/0.1        192.168.87.200  Et1/0.1        172.16.10.2     06 00  00      63 
                  0014 /0  0                     0014
                   /0  0     0.0.0.0                40    94.5
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       40                            Max plen:        40
                  Min TTL:        59                            Max TTL:         59
                  IP id:           0
                  Et0/0.1        10.10.10.2      Et1/0.1        172.16.10.2     06 00  00      64 
                  0015 /0  0                     0015
                   /0  0     0.0.0.0                40    96.0
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       40                            Max plen:        40
                  Min TTL:        59                            Max TTL:         59
                  IP id:           0
                  Et0/0.1        10.10.10.2      Et1/0.1        172.16.10.2     06 00  00      64 
                  0014 /0  0                     0014
                   /0  0     0.0.0.0                40    96.0
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       40                            Max plen:        40
                  Min TTL:        59                            Max TTL:         59
                  IP id:           0
                  Et0/0.1        10.234.53.1     Et1/0.1        172.16.10.2     06 00  00      63 
                  0015 /0  0                     0015
                   /0  0     0.0.0.0                40    94.5
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       40                            Max plen:        40
                  Min TTL:        59                            Max TTL:         59
                  IP id:           0
                  Et0/0.1        10.234.53.1     Et1/0.1        172.16.10.2     06 00  00      63 
                  0014 /0  0                     0014
                   /0  0     0.0.0.0                40    94.5
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       40                            Max plen:        40
                  Min TTL:        59                            Max TTL:         59
                  IP id:           0
                  Et0/0.1        172.30.231.193  Et1/0.1        172.16.10.2     06 00  00      63 
                  0015 /0  0                     0015
                   /0  0     0.0.0.0                40    94.5
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       40                            Max plen:        40
                  Min TTL:        59                            Max TTL:         59
                  IP id:           0
                  Et0/0.1        172.30.231.193  Et1/0.1        172.16.10.2     06 00  00      63 
                  0014 /0  0                     0014
                   /0  0     0.0.0.0                40    94.5
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:       40                            Max plen:        40
                  Min TTL:        59                            Max TTL:         59
                  IP id:           0
                  

                  There are 8 FTP flows shown in the output. You can use the Layer 2 information in the flows that is captured by the ip flow-capture command to identify the path the traffic is taking through the network. In this example, the traffic is being sent to R3 on VLAN 5 by R2. You can demonstrate that R2 is transmitting the traffic over interface 1/0.1 because the source MAC address (aaaa.bbb.cc03) belongs to 1/0.1 on R2. You can demonstrate that R3 is transmitting the traffic using VLAN 6 on interface 1/0.1 to interface 1/0.1 on R4, because the destination MAC address (aaaa.bbbb.cc06) belongs to interface 1/0.1 on R4.


                  Note


                  For more information on the ip flow-capture command, and the fields in the display output of the show ip cache verbose flow command, refer to the Cisco IOS NetFlow Command Reference .


                  You can use this information to mitigate this attack. One possible way to mitigate this attack is by configuring an extended IP access list that blocks all FTP traffic from the source IP addresses that Host A is spoofing and applying it Ethernet 0/0 on R2.

                  Analyze an FTP DoS Attack Using NetFlow Dynamic Top Talkers CLI Example

                  You can use the NetFlow Dynamic Top Talkers CLI feature to quickly identify the FTP top talkers in the network traffic that might be sending the traffic. This will show you the IP source addresses that Host A is using as it sends the DoS attack traffic.

                  R3# show ip flow top 50 aggregate source-address sorted-by bytes descending match destination-port min 20 max 21
                  There are 5 top talkers:
                  IPV4 SRC-ADDR         bytes        pkts       flows
                  ===============  ==========  ==========  ==========
                  10.231.185.254         5640         141           2
                  10.132.221.111         3680          92           2
                  10.10.12.1             3640          91           2
                  10.251.138.218         3600          90           2
                  10.71.200.138          1880          47           1
                  9 of 34 flows matched.
                  

                  Note


                  Only source IP addresses from FTP traffic are shown because of the match destination-port min 20 max 21 criteria. The source addresses are aggregated together so only the most relevant sources are shown.



                  Note


                  Only nine of the 34 flows matched because the rest of the flows are not FTP flows, therefore they do not meet the match criteria (match destination-port min 20 max 21).



                  Tip


                  The top talkers are displayed in descending order of the aggregated field by default.



                  Tip


                  You can enter the port numbers in their decimal values as shown, or in their hexadecimal equivalents of 0x14 and 0x15.


                  After you have identified FTP top talkers traffic you need to identify the source IP addresses of IP traffic that is being sent to the host that you believe is under attack.

                  R3# show ip flow top 50 aggregate source-address match destination-prefix 172.16.10.2/32
                  There are 6 top talkers:
                  IPV4 SRC-ADDR         bytes        pkts       flows
                  ===============  ==========  ==========  ==========
                  10.251.138.218         6642          18           4
                  10.231.185.254         5068          28           4
                  10.132.221.111        14818          25           4
                  10.106.1.1            12324          12           2
                  10.71.200.138         12564          18           3
                  10.10.12.1              560          14           2
                  19 of 33 flows matched.
                  

                  Tip


                  You can specify the host that you believe is under attack by using a prefix value of 32 with the match destination-prefix command.



                  Note


                  Only 19 of the 33 flows matched because the rest of the flows do not contain traffic that is destined for the host with the IP address of 172.16.10.2, therefore they do not meet the match criteria (match destination-prefix 172.16.10.2/32).


                  The final step is to cross reference the source IP addresses of any hosts that are sending any IP traffic to the host under attack with the list of source IP addresses from the FTP top talkers. This is required because the show ip flow top command does not support multiple match criteria. Therefore you cannot limit the top talkers to FTP traffic being sent to a specific host with a single show ip flow top command (match destination-port min 20 max 21 <and> match destination-prefix 172.16.10.2/32).

                  The host with the IP address of 10.106.1.1 is apparently not involved in this DoS attack because it is not in the display output from the show ip flow top 50 aggregate source-address sorted-by bytes descending match destination-port min 20 max 21 command. This means that it is not sending FTP traffic to the host that is under attack.

                  Therefore the host IP addressees involved in this FTP DoS attack are likely to be:

                  • 10.231.185.254

                  • 10.132.221.111

                  • 10.10.12.1

                  • 10.251.138.218

                  • 10.71.200.138

                  Now that you know the source addresses of the FTP traffic you can configure an extended access list that blocks FTP traffic from these address, and apply it to the interface that is closest to the point the traffic is entering your network.


                  Note


                  Unless you recognize that some of the source IP addresses are not legitimate IP addresses for your network it might not be possible to identify legitimate FTP traffic from FTP DoS attack traffic.


                  Configuring NetFlow Layer 2 and Sec Mon Exports to Capture Traffic From a Simulated ICMP Attack Example

                  The following example shows how to use the NetFlow Layer 2 and Security Monitoring Exports feature to find out that your network is being attacked by ICMP traffic. It uses the network shown in the figure below. Host A is sending ICMP ping packets to the FTP server.

                  Figure 8. Test Network


                  Tip


                  Keep track of the MAC addresses and IP addresses of the devices in your network. You can use them to analyze attacks and to resolve problems.


                  R2

                  !
                  hostname R2
                  !
                  interface Ethernet0/0
                   mac-address aaaa.bbbb.cc02
                   ip address 172.16.1.2 255.255.255.0
                  !
                  interface Ethernet1/0
                   mac-address aaaa.bbbb.cc03
                   no ip address
                  !
                  interface Ethernet1/0.1
                   encapsulation dot1Q 5
                   ip address 172.16.6.1 255.255.255.0
                  !
                  !
                  router rip
                   version 2
                   network 172.16.0.0
                   no auto-summary
                  !

                  R3

                  !
                  hostname R3
                  !
                  ip flow-capture fragment-offset
                  ip flow-capture packet-length
                  ip flow-capture ttl
                  ip flow-capture vlan-id
                  ip flow-capture icmp
                  ip flow-capture ip-id
                  ip flow-capture mac-addresses
                  !
                  interface Ethernet0/0
                   mac-address aaaa.bbbb.cc04
                   no ip address
                  !
                  interface Ethernet0/0.1
                   encapsulation dot1Q 5
                   ip address 172.16.6.2 255.255.255.0
                   ip accounting output-packets
                   ip flow ingress
                  !
                  interface Ethernet1/0
                   mac-address aaaa.bbbb.cc05
                   no ip address
                  !
                  interface Ethernet1/0.1
                   encapsulation dot1Q 6
                   ip address 172.16.7.1 255.255.255.0
                   ip accounting output-packets
                   ip flow egress
                  !
                  router rip
                   version 2
                   network 172.16.0.0
                   no auto-summary
                  !

                  R4

                  !
                  hostname R4
                  !
                  interface Ethernet0/0
                   mac-address aaaa.bbbb.cc07
                   ip address 172.16.10.1 255.255.255.0
                  !
                  interface Ethernet1/0
                   mac-address aaaa.bbbb.cc06
                   no ip address
                  !
                  interface Ethernet1/0.1
                   encapsulation dot1Q 6
                   ip address 172.16.7.2 255.255.255.0
                  !
                  router rip
                   version 2
                   network 172.16.0.0
                   no auto-summary
                  !

                  Analyze an ICMP Ping DoS Attack Using the show ip cache verbose flow command Example

                  The show ip cache verbose flow command displays the NetFlow flows. You can use this display output to identify the path that the ICMP traffic from Host A is taking as it is received and transmitted by R3.


                  Note


                  To reduce the space required to display the output from the show ip flow cache verbose flowcommand only the ICMP flows are shown.



                  Tip


                  Look for the flows that have ICMP in them and make a note of the interfaces, MAC addresses, and VLANs (if applicable) for the flows.


                  R3# show ip cache verbose flow
                  IP packet size distribution (122369 total packets):
                     1-32   64   96  128  160  192  224  256  288  320  352  384  416  448  480
                     .065 .665 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
                      512  544  576 1024 1536 2048 2560 3072 3584 4096 4608
                     .000 .000 .134 .000 .134 .000 .000 .000 .000 .000 .000
                  IP Flow Switching Cache, 278544 bytes
                    24 active, 4072 inactive, 404 added
                    176657 ager polls, 0 flow alloc failures
                    Active flows timeout in 30 minutes
                    Inactive flows timeout in 15 seconds
                  IP Sub Flow Cache, 25736 bytes
                    48 active, 976 inactive, 1088 added, 404 added to flow
                    0 alloc failures, 0 force free
                    1 chunk, 1 chunk added
                    last clearing of statistics never
                  Protocol         Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)
                  --------         Flows     /Sec     /Flow  /Pkt     /Sec     /Flow     /Flow
                  ICMP                27      0.0      1131   763      3.9    1557.4       3.6
                  Total:             380      0.0       267   257     13.0     382.8      12.6
                  SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs  Pkts
                  Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active
                  Et0/0.1        10.106.1.1      Et1/0.1        172.16.10.2     01 00  10     864 
                  0000 /0  0                     0800 /0  0     0.0.0.0              1500  1089.9
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      1500                            Max plen:       1500
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       8                            ICMP code:        0
                  IP id:           0
                  Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  00     864 
                  0000 /0  0                     0000 /0  0     0.0.0.0               554  1090.0
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      554                            Max plen:       554
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       0                            ICMP code:        0
                  IP id:           0                            FO:            185
                  Et0/0.1        10.231.185.254  Et1/0.1        172.16.10.2     01 00  00     864 
                  0000 /0  0                     0000 /0  0     0.0.0.0               554  1090.0
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      554                            Max plen:       554
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       0                            ICMP code:        0
                  IP id:           0                            FO:            185
                  Et0/0.1        10.10.12.1      Et1/0.1        172.16.10.200   01 00  00     864 
                  0000 /0  0                     0000 /0  0     0.0.0.0               554  1090.0
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      554                            Max plen:       554
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       0                            ICMP code:        0
                  IP id:           0                            FO:            185
                  Et0/0.1        10.132.221.111  Et1/0.1        172.16.10.2     01 00  10     864 
                  0000 /0  0                     0800 /0  0     0.0.0.0              1500  1089.9
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      1500                            Max plen:       1500
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       8                            ICMP code:        0
                  IP id:           0
                  Et0/0.1        10.251.138.218  Et1/0.1        172.16.10.2     01 00  00     864 
                  0000 /0  0                     0000 /0  0     0.0.0.0               554  1089.9
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      554                            Max plen:       554
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       0                            ICMP code:        0
                  IP id:           0                            FO:            185
                  Et0/0.1        10.10.12.1      Et1/0.1        172.16.10.200   01 00  10     864 
                  0000 /0  0                     0C01 /0  0     0.0.0.0              1500  1090.0
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      1500                            Max plen:       1500
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:      12                            ICMP code:        1
                  IP id:           0
                  Et0/0.1        10.106.1.1      Et1/0.1        172.16.10.2     01 00  00     864 
                  0000 /0  0                     0000 /0  0     0.0.0.0               554  1089.9
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      554                            Max plen:       554
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       0                            ICMP code:        0
                  IP id:           0                            FO:            185
                  Et0/0.1        10.251.138.218  Et1/0.1        172.16.10.2     01 00  10     864 
                  0000 /0  0                     0C01 /0  0     0.0.0.0              1500  1089.9
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      1500                            Max plen:       1500
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:      12                            ICMP code:        1
                  IP id:           0
                  Et0/0.1        10.71.200.138   Et1/0.1        172.16.10.2     01 00  10     864 
                  0000 /0  0                     0C01 /0  0     0.0.0.0              1500  1090.0
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      1500                            Max plen:       1500
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:      12                            ICMP code:        1
                  IP id:           0
                  Et0/0.1        10.132.221.111  Et1/0.1        172.16.10.2     01 00  00     864 
                  0000 /0  0                     0000 /0  0     0.0.0.0               554  1089.9
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      554                            Max plen:       554
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:       0                            ICMP code:        0
                  IP id:           0                            FO:            185
                  Et0/0.1        10.231.185.254  Et1/0.1        172.16.10.2     01 00  10     864 
                  0000 /0  0                     0C01 /0  0     0.0.0.0              1500  1090.0
                  MAC: (VLAN id) aaaa.bbbb.cc03  (005)          aaaa.bbbb.cc06  (006)
                  Min plen:      1500                            Max plen:       1500
                  Min TTL:        59                            Max TTL:         59
                  ICMP type:      12                            ICMP code:        1
                  IP id:           0
                  

                  There are 12 ICMP flows shown in the output. You can use the Layer 2 information in the flows that is captured by the ip flow-capture command to identify the path the traffic is taking through the network. In this example, the traffic is being sent to R3 on VLAN 5 by R2. You can demonstrate that R2 is transmitting the traffic over interface 1/0.1 because the source MAC address (aaaa.bbb.cc03) belongs to 1/0.1 on R2. You can demonstrate that R3 is transmitting the traffic using VLAN 6 on interface 1/0.1 to interface 1/0.1 on R4, because the destination MAC address (aaaa.bbbb.cc06) belongs to interface 1/0.1 on R4.


                  Note


                  For more information on the ip flow-capture command, and the fields in the display output of the show ip cache verbose flow command, refer to the Cisco IOS NetFlow Command Reference .


                  You can use this information to mitigate this attack. One possible way to mitigate this attack is by configuring an extended IP access list that blocks all ICMP traffic from the source IP addresses that Host A is spoofing and applying it Ethernet 0/0 on R2.

                  Analyze an ICMP Ping DoS Attack Using NetFlow Dynamic Top Talkers CLI Example

                  You can use the NetFlow Dynamic Top Talkers CLI feature to quickly identify the ICMP top talkers in the network traffic that might be sending the traffic. This will show you the IP source addresses that Host A is using as it sends the DoS attack traffic.

                  R3# show ip flow top 50 aggregate icmp
                  There are 3 top talkers:
                  ICMP TYPE  ICMP CODE       bytes        pkts       flows
                  =========  =========  ==========  ==========  ==========
                         12          1     2466000        1644           4
                          8          0     1233000         822           2
                          0          0     1366164        2466           6
                  12 of 25 flows matched.
                  

                  Note


                  Only 12 of the 25 flows matched because the rest of the flows are not ICMP flows.



                  Tip


                  The top talkers are displayed in descending order of the aggregated field by default.


                  After you have identified the ICMP types and code values in the network traffic, you need to determine the source IP addresses for the ICMP traffic that being sent to the FTP server.

                  R3# show ip flow top 50 aggregate source-address match icmp type 12 code 1
                  There are 4 top talkers:
                  IPV4 SRC-ADDR         bytes        pkts       flows
                  ===============  ==========  ==========  ==========
                  10.251.138.218       867000         578           1
                  10.231.185.254       865500         577           1
                  10.71.200.138        865500         577           1
                  10.10.12.1           867000         578           1
                  4 of 24 flows matched.
                  

                  Note


                  Only source IP addresses from ICMP traffic are shown because of the match icmp type 12 code 1 criteria. No aggregation is performed on the source IP addresses because there is only one flow for IP each address.



                  Note


                  Only four of the 24 flows matched because the rest of the flows did not meet the match criteria (match icmp type 12 code 1).


                  R3# show ip flow top 50 aggregate source-address match icmp type 8 code 0
                   
                  There are 2 top talkers:
                  IPV4 SRC-ADDR         bytes        pkts       flows
                  ===============  ==========  ==========  ==========
                  10.132.221.111      1095000         730           1
                  10.106.1.1          1095000         730           1
                  2 of 24 flows matched.
                  

                  Note


                  Only source IP addresses from ICMP traffic are shown because of the match icmp type 8 code 0 criteria. No aggregation is performed on the source IP addresses because there is only one flow for IP each address.



                  Note


                  Only two of the 24 flows matched because the rest of the flows did not meet the match criteria (match icmp type 8 code 0).


                  R3# show ip flow top 50 aggregate source-address match icmp type 0 code 0
                  There are 6 top talkers:
                  IPV4 SRC-ADDR         bytes        pkts       flows
                  ===============  ==========  ==========  ==========
                  10.251.138.218       416608         752           1
                  10.231.185.254       416608         752           1
                  10.132.221.111       416608         752           1
                  10.106.1.1           416608         752           1
                  10.71.200.138        416608         752           1
                  10.10.12.1           416608         752           1
                  6 of 24 flows matched.
                  

                  Note


                  Only source IP addresses from ICMP traffic are shown because of the match icmp type 0 code 0 criteria. No aggregation is performed on the source IP addresses because there is only one flow for IP each address.



                  Note


                  Only six of the 24 flows matched because the rest of the flows did not meet the match criteria (match icmp type 0 code 0).


                  The next step is to create a list of the source IP addresses that Host A is using.

                  • 10.251.138.218

                  • 10.231.185.254

                  • 10.71.200.138

                  • 10.10.12.1

                  • 10.132.221.111

                  • 10.106.1.1.

                  Now that you know the source addresses of the ICMP DoS attack traffic, you can mitigate this attack by configuring an extended access list that blocks ICMP traffic from these address and applying it to the interface that is closest to the point that the traffic is entering your network.

                  Configure NetFlow Filtering and Sampling Example

                  This example configuration contains the configuration commands required to use NetFlow filtering and sampling on the NetFlow router.

                  !
                  hostname Router
                  !
                  ip cef
                  !
                  flow-sampler-map icmp-dos-fs-map
                   mode random one-out-of 2
                  !
                  !
                  class-map match-any icmp-dos-class-map
                   match access-group 101
                  !
                  !
                  policy-map icmp-dos-policy-map
                    class icmp-dos-class-map
                     netflow-sampler icmp-dos-fs-map
                  !
                  interface Ethernet0/0
                   mac-address aaaa.bbbb.cc04
                   no ip address
                  !
                  interface Ethernet0/0.1
                   encapsulation dot1Q 5
                   ip address 172.16.6.2 255.255.255.0
                   service-policy input icmp-dos-policy-map
                  !
                  interface Ethernet1/0.1
                   encapsulation dot1Q 6
                   ip address 172.16.7.1 255.255.255.0
                   ip flow egress
                  !
                  ip flow-capture fragment-offset
                  ip flow-capture packet-length
                  ip flow-capture ttl
                  ip flow-capture vlan-id
                  ip flow-capture icmp
                  ip flow-capture ip-id
                  ip flow-capture mac-addresses
                  !
                  ip flow-top-talkers
                   top 5
                   sort-by bytes
                   match class-map icmp-dos-class-map
                  !
                  access-list 101 permit icmp any host 172.16.10.2
                  !
                  end
                  

                  Where to Go Next

                  See the "Additional References" section for links to configuration information about additional NetFlow features and services.

                  Additional References

                  Related Documents

                  Related Topic

                  Document Title

                  Overview of Cisco IOS NetFlow

                  "Cisco IOS NetFlow Overview"

                  The minimum information about and tasks required for configuring NetFlow and NetFlow Data Export

                  "Getting Started with Configuring NetFlow and NetFlow Data Export"

                  Tasks for configuring NetFlow to capture and export network traffic data

                  "Configuring NetFlow and NetFlow Data Export"

                  Tasks for configuring Configuring MPLS Aware NetFlow

                  Configuring MPLS Aware NetFlow

                  Tasks for configuring MPLS egress NetFlow accounting

                  Configuring MPLS Egress NetFlow Accounting and Analysis

                  Tasks for configuring NetFlow input filters

                  "Using NetFlow Filtering or Sampling to Select the Network Traffic to Track"

                  Tasks for configuring Random Sampled NetFlow

                  "Using NetFlow Filtering or Sampling to Select the Network Traffic to Track"

                  Tasks for configuring NetFlow aggregation caches

                  "Configuring NetFlow Aggregation Caches"

                  Tasks for configuring NetFlow BGP next hop support

                  "Configuring NetFlow BGP Next Hop Support for Accounting and Analysis"

                  Tasks for configuring NetFlow multicast support

                  "Configuring NetFlow Multicast Accounting"

                  Tasks for configuring NetFlow Reliable Export With SCTP

                  NetFlow Reliable Export With SCTP

                  Tasks for configuring NetFlow Layer 2 and Security Monitoring Exports

                  "NetFlow Layer 2 and Security Monitoring Exports"

                  Tasks for configuring the SNMP NetFlow MIB

                  "Configuring SNMP and using the NetFlow MIB to Monitor NetFlow Data"

                  Tasks for configuring the NetFlow MIB and Top Talkers feature

                  "Configuring NetFlow Top Talkers using Cisco IOS CLI Commands or SNMP Commands"

                  Information for installing, starting, and configuring the CNS NetFlow Collection Engine

                  "Cisco CNS NetFlow Collection Engine Documentation"

                  Standards

                  Standards

                  Title

                  There are no new or modified standards associated with this feature

                  --

                  MIBs

                  MIBs

                  MIBs Link

                  There are no new or modified MIBs associated with this feature.

                  To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

                  http:/​/​www.cisco.com/​go/​mibs

                  RFCs

                  RFCs

                  Title

                  There are no new or modified RFCs associated with this feature.

                  --

                  Technical Assistance

                  Description

                  Link

                  The Cisco Technical Support website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.

                  http:/​/​www.cisco.com/​techsupport

                  Feature Information for Detecting and Analyzing Network Threats With NetFlow

                  The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

                  Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

                  Table 11 Feature Information for NetFlow Layer 2 and Security Monitoring Exports

                  Feature Name

                  Releases

                  Feature Configuration Information

                  NetFlow Layer 2 and Security Monitoring Exports

                  12.3(14)T

                  The NetFlow Layer 2 and Security Monitoring Exports feature enables the capture of values from fields in Layer 3 and Layer 2 of IP traffic for accounting and security analysis.

                  The following commands were modified by this feature: ip flow-capture, ip flow-export and show ip cache verbose flow.

                  Support for capturing the value from the fragment offset field of IP headers added to NetFlow Layer 2 and Security Monitoring Exports1

                  12.4(2)T

                  The fragment-offset keyword for the ip flow-capture command enables capturing the value of the IP fragment offset field from the first fragmented IP datagram in a flow.

                  NetFlow Top Talkers

                  12.3(11)T,

                  12.2(25)S

                  This document references the Top Talkers feature from the NetFlow MIB and Top Talkers feature documentation.

                  Top Talkers uses NetFlow functionality to obtain information regarding heaviest traffic patterns and most-used applications in the network.

                  The following commands were introduced by this feature: cache-timeout, ip flow-top-talkers, match, show ip flow top-talkers, sort-by, and top.

                  NetFlow Dynamic Top Talkers CLI

                  12.4(4)T

                  The NetFlow Dynamic Top Talkers CLI allows you to se an overview of the traffic characteristics on your router by aggregating flows based on the fields such as source IP address, destination prefix, and so forth.

                  NetFlow Input Filters

                  12.3(4)T, 12.2(25)S

                  This document references the NetFlow Input Filters feature from the NetFlow Filtering and Sampling feature documentation.

                  Random Sampled NetFlow

                  12.3(4)T, 12.2(18)S, 12.0(26)S

                  This document references the Random Sampled NetFlow feature from the NetFlow Filtering and Sampling feature documentation.

                  1 This is a minor enhancement. Minor enhancements are not typically listed in Feature Navigator.

                  Glossary

                  data flowset --A collection of data records that are grouped in an export packet.

                  export packet --A type of packet built by a device (for example, a router) with NetFlow services enabled. The packet is addressed to another device (for example, the NetFlow Collection Engine). The packet contains NetFlow statistics. The other device processes the packet (parses, aggregates, and stores information about IP flows).

                  flow --A set of packets with the same source IP address, destination IP address, protocol, source/destination ports, and type-of-service, and the same interface on which flow is monitored. Ingress flows are associated with the input interface, and egress flows are associated with the output interface.

                  flowset --A collection of flow records that follow the packet header in an export packet. A flowset contains information that must be parsed and interpreted by the NetFlow Collection Engine. There are two types of flowsets: template flowsets and data flowsets. An export packet contains one or more flowsets, and both template and data flowsets can be mixed in the same export packet.

                  NetFlow --Cisco IOS accounting feature that maintains per-flow information.

                  NetFlow Aggregation --A NetFlow feature that lets you summarize NetFlow export data on an IOS router before the data is exported to a NetFlow data collection system such as the NetFlow Collection Engine. This feature lowers bandwidth requirements for NetFlow export data and reduces platform requirements for NetFlow data collection devices.

                  NetFlow Collection Engine (formerly NetFlow FlowCollector)--Cisco application that is used with NetFlow on Cisco routers and Catalyst series switches. The NetFlow Collection Engine collects packets from the router that is running NetFlow and decodes, aggregates, and stores them. You can generate reports on various aggregations that can be set up on the NetFlow Collection Engine.

                  NetFlow v9 --NetFlow export format Version 9. A flexible and extensible means of carrying NetFlow records from a network node to a collector. NetFlow Version 9 has definable record types and is self-describing for easier NetFlow Collection Engine configuration.

                  template --Describes the layout of a data flowset.

                  template flowset --A collection of template records that are grouped in an export packet.