List of Commands

This guide describes the commands supported in NCS 1020.

apc

To enable or disable APC at the link level, use the apc command on an OLT node.

apc { disable | enable }

Syntax Description

disable

Disable APC

enable

Enable APC

Command Default

(config-olc-ots)

Command Modes

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Use this command on an OLT node. APC can be disabled and enabled at a link level only from the APC Manager for the link.

Examples

The following is a sample configuration that disables APC.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#apc disable
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

The following is a sample configuration that enables APC.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#apc enable
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

apc-local

Use the apc-local disable command to disable APC on an agent node.

apc-local { RX | TX } disable

Syntax Description

RX

Disable APC agent in RX direction

TX

Disable APC agent in TX direction

disable

Disable APC on APC agent.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following is a sample configuration that disables APC locally.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#apc-local RX disable
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

apc-pause

Use the apc-pause command to pause APC.

apc-pause

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

If you run the apc-pause command when APC is in idle state, APC remains in the idle state until APC detects changes in the network that requires power correction. APC changes the status to paused after it detects changes, but does not perform power correction.

Running the apc-pause command, does not pause channel startup.

Examples

The following is a sample configuration that pauses APC.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#apc-pause
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

automatic-link-bringup

To enable automatic link bring up, use the automatic-link-bringup command. To disable automatic link bring up, use the no form of the command.

automatic-link-bringup

no automatic-link-bringup

Command Modes

(config-olc)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following sample configuration enables automatic link bring up.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#automatic-link-bringup
RP/0/RP0/CPU0:ios(config-olc)#commit
RP/0/RP0/CPU0:ios(config-olc)#end

The following sample configuration disables automatic link bring up.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#no automatic-link-bringup
RP/0/RP0/CPU0:ios(config-olc)#commit
RP/0/RP0/CPU0:ios(config-olc)#end

bfr-pause

Use the bfr-pause command to pause Band Failure Recovery(BFR). When BFR is paused, the recovery and failure procedures are not initiated in case of band failure. To resume BFR, use the no form of this command.

bfr-pause

no bfr-pause

Syntax Description

This command has no keywords or arguments.

Command Modes

Controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following is a sample output to pause BFR on the controller 0/0/0/0.

 RP/0/RP0/CPU0:#configure
RP/0/RP0/CPU0: (config)#optical-line-control
RP/0/RP0/CPU0: (config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0: (config-olc-ots)#bfr-pause 
RP/0/RP0/CPU0: (config-olc-ots)#commit
 

Examples

The following is a sample output to resume BFR on the controller 0/0/0/0.

 RP/0/RP0/CPU0:#configure
RP/0/RP0/CPU0: (config)#optical-line-control
RP/0/RP0/CPU0: (config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0: (config-olc-ots)#no bfr-pause 
RP/0/RP0/CPU0: (config-olc-ots)#commit
 

bridge-port routed-interface

Use the bridge-port routed-interface command to bridge traffic between two interfaces. For example, when connecting multiple NCS 1010 device in a Daisy Chain topology, use this command to bridge traffic between a NCS 1010 management interface and a TOR switch interface.

bridge-port routed-interface type interface-path-id

Syntax Description

type

Specify the Management Ethernet interface.

interface-path-id

Specify the physical or virtual interface.

Command Default

None

Command Modes

Interface Configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Task ID

Task ID Operation

Ethernet-services

read, write

Examples

The following example shows how to bridge traffic between a NCS 1010 management port and TOR switch port:

RP/0/RP0/CPU0:Box(config)#interface mgmtEth0/RP0/CPU0/1 
RP/0/RP0/CPU0:Box(config-if)# no ipv4 address 
RP/0/RP0/CPU0:Box(config-if)# no ipv6 address 
RP/0/RP0/CPU0:Box(config-if)# bridge-port routed-interface mgmtEth 0/RP0/CPU0/0 

cdp

To enable Cisco Discovery Protocol (CDP) globally or on an interface, use the cdp command in global configuration mode or in interface configuration mode. To disable CDP, use the no form of this command.

cdp

no cdp

Syntax Description

This command has no arguments or keywords.

Command Default

This command is enabled both at the global configuration level and at the interface configuration level.

Command Modes

Global configuration (config) and Interface configuration (config-if)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example enables CDP globally.


RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#cdp
RP/0/RP0/CPU0:ios(config)#commit

The following example enables CDP on the management interface.


RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#interface mgmtEth 0/RP0/CPU0/1
RP/0/RP0/CPU0:ios(config-if)#cdp
RP/0/RP0/CPU0:ios(config-if)#commit

cdp advertise

To enable CDP Version 1 advertising functionality on a device, use the cdp advertise command in global configuration mode. To disable CDP Version 1 functionality, use the no form of this command.

cdp advertise v1

no cdp advertise v1

Syntax Description

This command has no arguments or keywords.

Command Default

Enabled

Command Modes

Global configuration (config)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

When CDP is enabled, the device sends CDPv2 packets by default. CDP sends and receives CDPv1 packets if the device with which CDP is interacting does not process CDPv2 packets.

Examples

The following example configures CDP to use CDP Version 1 in communicating with neighboring devices.


RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#cdp advertise v1
RP/0/RP0/CPU0:ios(config)#commit

cdp holdtime

To specify the amount of time the receiving device must hold a CDP packet sent from another device before discarding it, use the cdp holdtime command in global configuration mode. To revert to the default setting, use the no form of this command.

cdp holdtime seconds

no cdp holdtime

Syntax Description

seconds

Specifies the hold time to be sent in the CDP update packets. The default is 180 seconds. The range is 10 to 255 seconds.

Command Default

180 seconds

Command Modes

Global configuration (config)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

CDP packets are sent with a time to live, or hold time, value. The receiving device will discard the CDP information in the CDP packet after the hold time has elapsed.

You can set the hold time lower than the default setting of 180 seconds if you want the receiving devices to update their CDP information more rapidly.

The CDP hold time must be set to a higher number of seconds than the time between CDP transmissions, which is set using the cdp timer command.

Examples

The following example configures CDP holdtime to 120 seconds.


RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#cdp holdtime 120
RP/0/RP0/CPU0:ios(config)#commit

cdp timer

To specify the frequency at which CDP update packets are sent., use the cdp timer command in global configuration mode. To revert to the default setting, use the no form of this command.

cdp timer seconds

no cdp timer

Syntax Description

seconds

Specifies the frequency at which CDP update packets are sent. The default is 60 seconds. The range is 5 to 254 seconds.

Command Default

60 seconds

Command Modes

Global configuration (config)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

A lower timer setting causes CDP update packets to be sent more frequently.

Examples

The following example configures CDP timer to 65 seconds.


RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#cdp timer 65
RP/0/RP0/CPU0:ios(config)#commit

commit

To commit the target configuration to the active (running) configuration, use the commit command in any configuration mode.

commit [ replace ]

Syntax Description

replace

Replaces the entire running configuration with the contents of the target configuration.

Command Default

None

Command Modes

Cisco IOS XR Configuration

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

To remove the entire running configuration on the NCS 1010 node, use the following command:
Fri Apr 29 06:48:46.236 UTC
RP/0/RP0/CPU0:P2B_DT_02(config)#commit replace
Fri Apr 29 06:48:53.199 UTC
This commit will replace or remove the entire running configuration. This
operation can be service affecting.
Do you wish to proceed? [no]: yes
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#end

connector-loss

To configure connector loss, use the connector-loss command.

connector-loss { rx | tx } value

Syntax Description

rx

Connector loss at receive point

tx

Connector loss at transmit point

value

Connector loss in range 0–20. Unit: 1 dB

Command Default

The default connector loss is:

  • 0.25 dB for ports without Raman module

  • 0.3 dB for ports with Raman module

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example is a sample configuration that configures rx and tx connector losses to 0.1 dB.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control 
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#connector-loss rx 1
RP/0/RP0/CPU0:ios(config-olc-ots)#connector-loss tx 1
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

controller dfb

To configure the DFB controller, use the controller dfb command in the controller configuration mode.

controller dfb R/S/I/P [ tx-voa-attenuation value | tx-low-threshold value | sec-admin-state {normal | maintenance} | transmit-shutdown | shutdown ]

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the DFB controller.

tx-voa-attenuationvalue

Configures the DFB TX VoA attenuation set point.

tx-low-thresholdvalue

Configures the low transmit power threshold.

sec-admin-state

Configures the administrative state of the controller. The values are maintenance or normal.

transmit-shutdown

Shuts down the DFB laser.

shutdown

Disables the configuration of the controller.

Command Default

None

Command Modes

controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

In the following sample, the tx-voa-attenuation is set to 2 dB.

RP/0/RP0/CPU0:ios#config
Thu Apr 21 17:00:57.654 UTC
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#controller dfb 0/0/0/0 tx-voa-attenuation 20
RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)#end

To view the configured value, use the following command:

RP/0/RP0/CPU0:ios#sh controller dfb 0/0/0/0
Thu Apr 21 17:02:06.316 UTC
Controller State: Up
Transport Admin State: In Service
Laser State: On
Alarm Status:
-------------
Detected Alarms: None
Alarm Statistics:
-----------------
RX-LOS-P = 0
TX-POWER-FAIL-LOW = 0
Parameter Statistics:
---------------------
Total TX Power = 20.00 dBm
Total RX Power = 10.00 dBm
TX Voa Attenuation = 2.0 dB
Configured Parameters:
-------------
TX Voa Attenuation = 2.0 dB

The DFB laser attenuates based on the updated value and the TX power changes accordingly.

In the following sample, the sec-admin-state is set to maintenance.

RP/0/RP0/CPU0:ios#config
RP/0/RP0/CPU0:ios(config)#controller dfb 0/0/0/0 sec-admin-state maintenance
RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)#end
RP/0/RP0/CPU0:ios#sh controllers dfb 0/0/0/0
Thu Apr 21 17:05:41.311 UTC
Controller State: Up
Transport Admin State: Maintenance
Laser State: On
Alarm Status:
-------------
Detected Alarms: None
Alarm Statistics:
-----------------
RX-LOS-P = 0
TX-POWER-FAIL-LOW = 0
Parameter Statistics:
---------------------
Total TX Power = 20.00 dBm
Total RX Power = 10.00 dBm
TX Voa Attenuation = 2.0 dB
Configured Parameters:
-------------
TX Voa Attenuation = 2.0 dB

In the following sample, the DFB controller is shut down.

RP/0/RP0/CPU0:ios#config
RP/0/RP0/CPU0:ios(config)#controller dfb 0/0/0/0 shutdown
RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)#end
RP/0/RP0/CPU0:ios#sh controllers dfb 0/0/0/0
Thu Apr 21 17:08:40.211 UTC
Controller State: Administratively Down
Transport Admin State: Out Of Service
Laser State: Off
Alarm Status:
-------------
Detected Alarms: None
Alarm Statistics:
-----------------
RX-LOS-P = 0
TX-POWER-FAIL-LOW = 0
Parameter Statistics:
---------------------
Total TX Power = -50.00 dBm 
Total RX Power = 10.00 dBm
TX Voa Attenuation = 2.0 dB
Configured Parameters:
-------------
TX Voa Attenuation = 2.0 dB

controller-oms

To configure the OMS controller, use the controller oms command in the controller OTS configuration mode.

Use the following parameters to configure different configurations for an OMS controller on breakout or multiplexer/demultiplexer module.

controller oms R/S/I/P [ tone-rate ] [ tone-pattern-expected ] [ tone-detect-oob ]

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OMS controller.

tone-ratevalue

Configures the tone rate for tone generation.

tone-pattern-expectedvalue

Checks for the transmitted tone pattern from the OTS controller or terminal device.

tone-detect-oobvalue

Detects the out-of-band (OOB) frequency transmitted from the OTS controller or the terminal device.

Command Default

None

Command Modes

controller configuration mode

Command History

Release Modification
Release 24.2.1

Introduced this command.

Examples

The following output is a sample of configuring various tone generation parameters using the controller oms 0/0/0/0 command.

RP/0/RP0/CPU0:(config)#controller oms 0/2/0/0
RP/0/RP0/CPU0:(config-Oms)#tone-rate 25
RP/0/RP0/CPU0:(config-Oms)#tone-pattern-expected abcd1234
RP/0/RP0/CPU0:(config-Oms)#tone-detect-oob
RP/0/RP0/CPU0:(config-Oms)#commit

controller osc

To configure the OSC controller, use the controller osc command in the controller configuration mode.

controller osc R/S/I/P [ transmit-power value | sec-admin-state {normal | maintenance} | tx-low-threshold value | shutdown ]

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

transmit-power value

Configures the transmit power.

sec-admin-state

Configures the administrative state of the controller. The values are maintenance or normal.

tx-low-threshold value

Configures low transmit power threshold

shutdown

Disables the configuration of the controller.

Command Default

None

Command Modes

Controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

In the following sample, the transmit-power is set to 2 dBm. The transmit power can be changed only after the OSC laser probing loop is closed and the OSC transmit power is stable. The OSC transmit power depends on the span length. If the span loss is high, the OSC Tx power is low and vice versa.

RP/0/RP0/CPU0:ios(config)#controller osc 0/0/0/0 transmit-power 20
Fri May 13 11:26:53.445 UTC
WARNING! Changing TX power can impact traffic
RP/0/RP0/CPU0:ios(config)#commit
Fri May 13 11:26:55.127 UTC
RP/0/RP0/CPU0:ios(config)#end
RP/0/RP0/CPU0:ios#sh controllers osc 0/0/0/0
Fri May 13 11:26:59.542 UTC
Controller State: Up
Transport Admin State: In Service
Laser State: On
Alarm Status:
-------------
Detected Alarms: None
Alarm Statistics:
-----------------
RX-LOS-P = 0
TX-POWER-FAIL-LOW = 0
Parameter Statistics:
---------------------
Total TX Power = 1.89 dBm
Total RX Power = -17.30 dBm

Configured Parameters:
-------------

In the following sample, the sec-admin-state is set to maintenance.

RP/0/RP0/CPU0:ios#config
RP/0/RP0/CPU0:ios(config)#controller osc 0/0/0/0 sec-admin-state maintenance
RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)#end
RP/0/RP0/CPU0:ios#sh controllers osc 0/0/0/0
Fri Apr 22 15:55:36.324 UTC
Controller State: Up
Transport Admin State: Maintenance
Laser State: On
Alarm Status:
-------------
Detected Alarms: None
Alarm Statistics:
-----------------
RX-LOS-P = 0
TX-POWER-FAIL-LOW = 0
Parameter Statistics:
---------------------
Total TX Power = -10.00 dBm
Total RX Power = -30.00 dBm
Configured Parameters:
-------------

In the following sample, the OSC controller is shut down.

RP/0/RP0/CPU0:ios#config
RP/0/RP0/CPU0:ios(config)#controller osc 0/0/0/0 shutdown
RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)#end
RP/0/RP0/CPU0:ios#sh controllers os 0/0/0/0
Tue Apr 12 17:33:12.998 UTC
Controller State: Administratively Down
Transport Admin State: Out Of Service
Laser State: Off
Alarm Status:
-------------
Detected Alarms: None
Alarm Statistics:
-----------------
RX-LOS-P = 0
TX-POWER-FAIL-LOW = 0
Parameter Statistics:
---------------------
Total TX Power = -50.00 dBm
Total RX Power = -30.00 dBm
Configured Parameters:
-------------

controller ots

To configure the OTS controller, use the controller ots command in the controller OTS configuration mode.

Use the following parameters to configure different configurations for an OTS controller on an NCS 1020 node.

controller ots R/S/I/P [ tx-voa-attenuation value ] [ egress-ampli-gain-range {normal | extended} ] [ egress-ampli-gain value ] [ egress-ampli-tilt value ] [ egress-ampli-osri {on | off} ] [ egress-ampli-safety-control-mode {auto | disabled} ] [ egress-ampli-force-apr {on | off} ] [ ingress-ampli-gain-range {normal | extended} ] [ ingress-ampli-gain value ] [ raman-tx-power Raman-transmit-pump-instance ] [ power power-value ] [ raman-tx-power-disable Raman-transmit-pump-instance ] [ raman-force-apr {on | off} ] [ raman-osri {on | off} ] [ ] [ otdr scan-mode expert ] [ otdr rx auto reflectance-threshold value ] [ otdr rx auto splice-loss-threshold value ] [ otdr rx expert pulse-width value ] [ otdr tx auto reflectance-threshold value ] [ otdr tx auto splice-loss-threshold value ] [ raman-tx-power <1-N> value value ] [ otdr rx auto raman-setpoint value ] [ otdr tx auto raman-setpoint value ] [ otdr rx auto excess-reflection-threshold value ] [ otdr tx auto excess-reflection-threshold value ] [ otdr rx back-scattering value ] [ otdr tx back-scattering value ] [ otdr rx refractive-index value ] [ otdr tx refractive-index value ] [ otdr rx expert pulse-width value ] [ otdr tx expert pulse-width value ] [ otdr rx expert capture-end value ] [ otdr tx expert capture-end value ] [ otdr rx expert capture-start value ] [ otdr tx expert capture-start value ] [ otdr rx expert scan duration value ] [ otdr tx expert scan duration value ] [ otdr rx auto excess-orl-threshold value ] [ otdr tx auto excess-orl-threshold value ] [ otdr rx auto excess-attenuation-threshold value ] [ otdr tx auto excess-attenuation-threshold value ]

controller ots R/S/I/P [ tone-rate ] [ tone-pattern-expected ] [ tone-frequency ]

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OTS controller.

tx-voa-attenuationvalue

Configures the TX VoA attenuation set point.

egress-ampli-gain-range {normal | extended}

Configures egress amplification gain range to normal or extended.

egress-ampli-gain value

Configures egress amplification gain.

egress-ampli-tilt value

Configures egress amplifier tilt.

egress-ampli-osri {on | off}

Enables or disables egress optical safety remote interlock (OSRI).

egress-ampli-safety-control-mode {auto | disabled}

Configure egress amplification safety control mode to auto or disables it.

egress-ampli-force-apr {on | off}

Enables or disables egress amplification force automatic power reduction.

raman-tx-power Raman-transmit-pump-instance power power-value

Configures Raman transmit power parameters.

raman-tx-power-disable Raman-transmit-pump-instance

Disables Raman transmit power.

raman-force-apr {on | off}

Enables or disables Raman force APR.

raman-osri {on | off}

Enables or disables Raman optical safety remote interlock (OSRI).

ingress-ampli-gain-range {normal | extended}

Configure ingress amplification safety control mode to auto or disables it.

ingress-ampli-gain value

Configures ingress amplification gain.

otdr rx auto reflectance-threshold value

Configures OTDR reflectance threshold in RX direction in auto mode.

otdr rx auto splice-loss-threshold value

Configures OTDR splice loss threshold in RX direction in auto mode.

otdr rx expert pulse-width value

Configures OTDR pulse width threshold in RX direction in expert mode.

otdr tx auto reflectance-threshold value

Configures OTDR reflectance threshold in TX direction in auto mode.

otdr tx auto splice-loss-threshold value

Configures OTDR splice loss threshold in TX direction in auto mode.

otdr scan-mode expert

Configures OTDR scan in expert.

raman-tx-power <1-N> value value

Configures the target Raman transmit power value for multiple instances.

otdr rx auto raman-setpoint value

Configures OTDR Raman in RX direction in auto mode.

otdr tx auto raman-setpoint value

Configures OTDR Raman in TX direction in auto mode.

otdr rx auto excess-reflection-threshold value

Configures OTDR excess reflection threshold in RX direction in auto mode.

otdr tx auto excess-reflection-threshold value

Configures OTDR excess reflection threshold in TX direction in auto mode.

otdr rx back- scattering value

Configures OTDR back scattering in RX direction.

otdr tx back- scattering value

Configures OTDR back scattering in TX direction.

otdr rx refractive-index value

Configures OTDR refractive index in RX direction in auto mode.

otdr tx refractive-index value

Configures OTDR refractive index in TX direction in auto mode.

otdr rx expert pulse-width value

Configures OTDR pulse width in RX direction in expert mode.

otdr tx expert pulse-width value

Configures OTDR pulse width in TX direction in expert mode.

otdr rx expert capture-end value

Configures OTDR capture end time in RX direction in expert mode.

otdr tx expert capture-end value

Configures OTDR capture end time in TX direction in expert mode.

otdr rx expert capture-start value

Configures OTDR capture start time in RX direction in expert mode.

otdr tx expert capture-start value

Configures OTDR capture start time in TX direction in expert mode.

otdr rx expert scan duration value

Configures OTDR scan duration in RX direction in expert mode.

otdr tx expert scan duration value

Configures OTDR scan duration in TX direction in expert mode.

otdr rx auto excess-orl-threshold value

Configures OTDR excess Optical Return Loss (ORL) threshold in RX direction in auto mode.

otdr tx auto excess-orl-threshold value

Configures OTDR excess ORL threshold in TX direction in auto mode.

otdr rx auto excess-attenuation-threshold value

Configures OTDR excess attenuation threshold in RX direction in auto mode.

otdr tx auto excess-attenuation-threshold value

Configures OTDR excess attenuation threshold in TX direction in auto mode.

tone-rate value

Configures the tone rate for tone generation.

tone-pattern value

Configures the tone pattern for tone generation.

tone-frequency value

Configures the tone frequency for tone generation.

Command Default

None

Command Modes

controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following output is a sample of configuring various otdr parameters using the controller ots 0/0/0/0 command.

RP/0/RP0/CPU0:ios#RP/0/RP0/CPU0:ios#config
RP/0/RP0/CPU0:ios(config)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-Ots)#otdr scan-mode expert
RP/0/RP0/CPU0:ios(config-Ots)#otdr rx auto reflectance-threshold -50
RP/0/RP0/CPU0:ios(config-Ots)#otdr rx auto splice-loss-threshold 200
RP/0/RP0/CPU0:ios(config-Ots)#otdr rx expert pulse-width 6000
RP/0/RP0/CPU0:ios(config-Ots)#otdr rx auto excess-orl-threshold 600
RP/0/RP0/CPU0:ios(config-Ots)#otdr rx auto excess-reflection-threshold -35
RP/0/RP0/CPU0:ios(config-Ots)#otdr rx auto excess-attenuation-threshold 5
RP/0/RP0/CPU0:ios(config-Ots)#otdr tx auto reflectance-threshold -50
RP/0/RP0/CPU0:ios(config-Ots)#otdr tx auto splice-loss-threshold 200
RP/0/RP0/CPU0:ios(config-Ots)#otdr tx auto excess-orl-threshold 600
RP/0/RP0/CPU0:ios(config-Ots)#otdr tx auto excess-reflection-threshold -50
RP/0/RP0/CPU0:ios(config-Ots)#otdr tx auto excess-attenuation-threshold 5
RP/0/RP0/CPU0:ios(config-Ots)#commit

The following output is a sample of configuring various tone generation parameters using the controller ots 0/0/0/4 command.

RP/0/RP0/CPU0:(config)#controller ots 0/0/0/4
RP/0/RP0/CPU0:(config-Ots)#tone-rate 25
RP/0/RP0/CPU0:(config-Ots)#tone-frequency 191.175 ( OOB frequency )
RP/0/RP0/CPU0:(config-Ots)#tone-pattern abcd1234
RP/0/RP0/CPU0:(config-Ots)#commit

controller ots-och

To configure the OTS-OCH controller on the add-drop port to which the cross-connection is made on the COM side, use the controller ots-och command in the controller configuration mode.

controller ots-och R/S/I/P/channel-id add-drop-channel ots-och R/S/I/P/channel-id

Syntax Description

R/S/I/P/channel-id

Rack/Slot/Instance/Port/Channel-id of the OTS-OCH controller.

add-drop-channel

Creates the add/drop channel on the COM side.

Command Default

None

Command Modes

Controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

To configure the optical cross-connect, use the following commands:

Mon Apr 4 14:54:32.834 UTC
RP/0/RP0/CPU0:ios(config)#controller ots-och 0/0/0/0/1 add-drop-channel ots-och 0/0/0/33/1
RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)

To view the OTS-OCH controllers, use the following command:

RP/0/RP0/CPU0:ios#sh controller ots-och ?
0/0/0/0/1 Ots-Och Interface Instance
0/0/0/33/1 Ots-Och Interface Instance
R/S/I/P/B or R/S/I/P Forward interface in Rack/Slot/Instance/Port/Breakout format or
R/S/I/P format

To view the parameters of the OTS-OCH controller (LINE side), use the following command:

RP/0/RP0/CPU0:ios#sh controllers ots-och 0/0/0/0/1
Tue Apr  5 06:32:29.696 UTC

 Controller State: Up

 Transport Admin State: In Service

         Alarm Status:
         -------------
         Detected Alarms: None


         Alarm Statistics:
         -----------------
         RX-LOS-P = 0
         TX-POWER-FAIL-LOW = 0

         Parameter Statistics:
         ---------------------
         Total RX Power = -10.50 dBm
         Total TX Power = -10.50 dBm


         Cross Connect Info:
         ---------------------
         Add-Drop Channel  = Ots-Och0/0/0/33/1




         Configured Parameters:
         -------------

RP/0/RP0/CPU0:ios#


Note


The Add/Drop channel that is cross connected to the line port, 0/0/0/0/1 is displayed in the output.


drop-psd

Use the drop-psd command to set the target PSD for drop ports.

drop-psd value

Syntax Description

value

PSD in range -30.0 dBm per 12.5 GHz to 23.0 dBm per 12.5 GHz in increments of 0.1 dBm per 12.5 GHz.

Command Default

The default target PSD for drop ports is –9.4 dB.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

The NCS 1010 applies drop PSD configuration for channels with cross connect configurations.

Examples

The following is a sample configuration that sets the target PSD at drop ports to –25 dB.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#drop-psd -250
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
Tue Apr 26 09:50:12.055 UTC
RP/0/RP0/CPU0:ios(config-olc-ots)#end

dual-band-psd

Use the dual-band-psd command to set the target dual-band PSDs when using C+L band configuration.

dual-band-psd index value

Syntax Description

index

PSD index 1–33.

value

PSD in range -50.0 dBm per 12.5 GHz to -32.0 dBm per 12.5 GHz in increments of 0.1 dBm per 12.5 GHz.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example shows how to set the dual band psd values -50 and -49 on setpoints 1 and 2 respectively, on the 0/0/0/0 controller .

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#dual-band-psd 1 -50
RP/0/RP0/CPU0:ios(config-olc-ots)#dual-band-psd 2 -49
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

environment chassis-door-alarm

Use the environment chassis-door-alarm command to report the door alarm when closing and opening the door.

Enable Chassis Door Alarm Command

environment chassis-door-alarm enable

Disable Chassis Door Alarm Command

no environment chassis-door-alarm enable

Syntax Description

environment chassis-door-alarm enable

Enables chassis door alarm.

no environment chassis-door-alarm enable

Disables chassis door alarm.

Command Default

The chassis door alarm is disabled.

Command Modes

Global configuration (config)

Command History

Release Modification
Cisco IOS XR Release 24.3.1

This command was introduced.

Usage Guidelines

Use this command to enable or disable the chassis door alarm.

Examples

The following example shows how to enable the chassis door alarm:

RP/0/RP0/CPU0:ios(config)#environment chassis-door-alarm enable 
RP/0/RP0/CPU0:ios(config)#commit
Fri May 24 11:26:14.715 UTC

The following example shows how to disable the chassis door alarm:

RP/0/RP0/CPU0:ios(config)#no environment chassis-door-alarm enable 
RP/0/RP0/CPU0:ios(config)#commit
Fri May 24 11:26:14.715 UTC
RP/0/RP0/CPU0:May 24 11:26:14.880 UTC: envmon[190]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :Chassis Door alarm :CLEAR :0:

fiber-type

To configure fiber type, use fiber-type command.

fiber-type type

Syntax Description

type

Fiber type. Possible fiber types are:

  • E-LEAF

  • FREE-LIGHT

  • METRO-CORE

  • SMF

  • SMF-28E

  • TERA-LIGHT

  • TW-RS

  • TW-Reach

  • TW-minus

  • TW-plus

  • ULL-SMF28

Command Default

SMF is the default fiber-type.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example is a sample configuration that configures fiber-type to SMF.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control 
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#fiber-type SMF
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

fpd auto-upgrade

To enable or disable automatic FPD upgrade, use the fpd auto-upgrade command in Cisco IOS XR Configuration mode.

fpd auto-upgrade { enable | disable }

Syntax Description

enable | disable

Enables or disables automatic FPD upgrade

Command Default

Automatic FPD upgrade is enabled.

Command Modes

Cisco IOS XR Configuration

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example shows how to disable automatic FPD upgrade.


RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#fpd auto-upgrade disable
RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)#end

gain-estimator

To enable or disable Gain Estimator, use the gain-estimator command.

gain-estimator { disable | enable }

Syntax Description

disable

Disable Gain Estimator

enable

Enable Gain Estimator

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following output is a sample configuration that disables Gain Estimator.

RP/0/RP0/CPU0:ios#configure terminal
Mon Jun 13 05:35:20.510 UTC
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#gain-estimator disable
RP/0/RP0/CPU0:ios(config-olc-ots)#commit

The following output is a sample configuration that enables Gain Estimator.

RP/0/RP0/CPU0:ios#configure terminal
Mon Jun 13 05:35:27.511 UTC
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#gain-estimator enable
RP/0/RP0/CPU0:ios(config-olc-ots)#commit

http client connection

To configure the connection for http client, use the http client connection command in XR Config mode. To restore the default value, use the no form of this command.

http client connection { retry count | timeout seconds }

Syntax Description

retry count

Specifies how many times HTTP Client resends a connection request. Range is from 1 to 5. The default value is 0.

timeout seconds

The time interval (in seconds) that HTTP client waits for a server connection to establish before giving up. Range is from 1 to 60 seconds. The default value is 10 seconds.

Command Default

The connection retry is not configured by default. The default connection timeout is set to 10 seconds.

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Modes

HTTP configuration

Usage Guidelines

Use this command to set the connection timeout or connection retry count.

Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows how to configure the connection request retry to two times:

RP/0/RP0/CPU0:router(config)#http client connection retry 2

Examples

The following example shows how to configure the connection request timeout to 20 seconds:

RP/0/RP0/CPU0:router(config)#http client connection timeout 20

http client response

To configure the time interval (in seconds) for HTTP Client to wait for a response from the server before giving up, use the http client response command in XR Config mode. To restore the default value, use the no form of this command.

http client response { timeout seconds }

Syntax Description

timeout seconds

The time interval (in seconds) that HTTP client waits for a response from the server before giving up. Range is from 1 to 300 seconds. The default value is 30 seconds.

Command Default

The response timeout is 30 seconds by default.

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Modes

HTTP configuration

Usage Guidelines

Use this command to configure the response timeout.

Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows how to configure the response timeout to 40 seconds:

RP/0/RP0/CPU0:router(config)#http client response timeout 40

http client secure-verify-host

To enable verifying host in peer's certificate, use the http client secure-verify-host command in XR Config mode. To restore the default value, use the no form of this command.

http client secure-verify-host

Syntax Description

secure-verify-host

Verifies the host in peer's certificate. This is enabled by default. To disable, use the command http client secure-verify-host disable

Command Default

Host verification is enabled by default.

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Modes

HTTP configuration

Usage Guidelines

Use the http client secure-verify-host command to disable the host verification.

Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows how to disable host verification :

RP/0/RP0/CPU0:router(config)#http client secure-verify-host disable

http client secure-verify-peer

To enable verifying authenticity of the peer certificate, use the http client secure-verify-peer command in XR Config mode. To restore the default value, use the no form of this command.

http client secure-verify-peer

Syntax Description

secure-verify-peer

Verifies authenticity of the peer certificate. This is enabled by default. To disable, use the command http client secure-verify-peer disable

Command Default

Peer verification is enabled by default.

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Modes

HTTP configuration

Usage Guidelines

Use the http client secure-verify-peer command to disable the peer verification.

Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows how to disable peer verification :

RP/0/RP0/CPU0:router(config)#http client secure-verify-peer disable

http client source interface

To specify the interface for source address for Hypertext Transfer Protocol (HTTP) connections, use the http client source-interface command in XR Config mode. To remove the http client source-interface command from the configuration file and restore the system to its default condition, use the no form of this command.

http client source-interface { ipv4 | ipv6 }

Syntax Description

ipv4 ip-address

Enter ipv4 address from interface.

ipv6 ip-address

Enter ipv6 address from interface.

Command Default

No default behavior or values.

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Modes

HTTP configuration

Usage Guidelines

Use the http client source-interface command to configure ipv4 and ipv6 source interfaces. If both the source interfaces are configured, then the source interface is selected depending on the host DNS resolution.

Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows how to configure ipv4 source interface for HTTP connection:

RP/0/RP0/CPU0:router(config)#http client source-interface ipv4 gigabitEthernet 0/0/0/0

Examples

The following example shows how to configure ipv6 source interface for HTTP connection:

RP/0/RP0/CPU0:router(config)#http client source-interface ipv6 gigabitEthernet 0/0/0/0

http client ssl

To configure Secure Socket Layer (SSL) version to be used for HTTPS requests, use the http client ssl command in XR Config mode. To restore the default value, use the no form of this command.

http client ssl version

Syntax Description

ssl version

Specify the SSL version to be used for HTTPS requests. Select one of the following versions:

  • tls1.0 - Forces TLSv1.0 to be used for HTTPS requests.

  • tls1.1 - Forces TLSv1.1 to be used for HTTPS requests.

  • tls1.2 - Forces TLSv1.2 to be used for HTTPS requests.

By default libcurl does not force the TLS version.

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Default

By default, the SSL version is not configured.

Command Modes

HTTP configuration

Usage Guidelines

Use this command to configure the ssl version to be used in HTTPS requests.

Task ID

Task ID

Operations

config-servicess

read, write

Examples

The following example shows how to configure the SSL version to tls1.1:

RP/0/RP0/CPU0:router(config)#http client ssl tls1.1

http client tcp-window-scale

To configure the TCP window scale factor for high latency links, use the http client tcp-window-scale command in XR Config mode. To restore the default value, use the no form of this command.

http client tcp-window-scale scale

Syntax Description

scale

Specify the TCP window scale for HTTP requests. Range is 1 to 14.

Command Default

By default, TCP window scale is disabled.

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Modes

HTTP configuration

Usage Guidelines

Use this command to configure the TCP window scale for HTTP requests.


Note


Currently, this is enabled for copying of files using HTTP.


Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows how to set the TCP window scale to 10:

RP/0/RP0/CPU0:router(config)#http client tcp-window-scale 10

http client version

To configure the HTTP version to be used for HTTP requests, use the http client version command in XR Config mode. To restore the default value, use the no form of this command.

http client version version

Syntax Description

versionversion

Specify the HTTP version to be used for HTTP requests. Select one of the following versions:

  • 1.0 - Forces HTTP1.0 to be used for all HTTP requests.

  • 1.1 - Forces HTTP1.1 to be used for all HTTP requests.

  • default - libcurl picks up HTTP version automatically.

Command Default

By default, libcurl does not force the HTTP version.


Note


HTTP Client uses libcurl version 7.30


Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Modes

HTTP configuration

Usage Guidelines

Use this command to configure the HTTP version to be used in HTTP requests.

Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows how to configure the HTTP version to 1.1:

Router(config)#http client version 1.1

http client vrf

To configure a new VRF to be used by the HTTP client, use the http client vrf command. To remove the specified vrf, use the no form of this command.

http client vrf vrf-name

Syntax Description

vrf-name

Specifies the name of the VRF to be used by the HTTP client.

Command Default

If not configured, the default VRF "default-vrf" will be used.

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Command Modes

HTTP configuration

Usage Guidelines

A HTTP client can have only one VRF. If a specific VRF is not configured for the HTTP client, the default VRF is assumed.

Task ID

Task ID

Operations

config-services

read, write

Examples

The following example shows the HTTP client being configured to start with the specified VRF:

RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# http client vrf green

hw-module

To create the OTS-OCH controller, use the hw-module location command in IOS XR configuration mode.

hw-module location location terminal-ampli | inline-ampli grid-mode mode channel-id channel-id centre-freq frequency width channel width

Syntax Description

location

Specifies the location of the hardware module. The location is 0/0/NXR0.

terminal-ampli | inline-ampli

terminal-ampli is used for OLT nodes and inline-ampli is used for ILA nodes.

grid-mode value

Specifies the optical spectrum on the interfaces.

centre-freq frequency

Defines the central frequency of the channel.

width channel-width

Defines the width of the channel.

Command Default

None

Command Modes

Cisco IOS XR Configuration

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

To create the OTS-OCH controller on the LINE side of an ILA-C node, use the following commands:
RP/0/RP0/CPU0:ios#config
Thu Apr 7 13:14:49.841 UTC
RP/0/RP0/CPU0:ios(config)#
RP/0/RP0/CPU0:ios(config)#hw-module location 0/0/NXR0 inline-ampli grid-mode flex
RP/0/RP0/CPU0:ios(config-hwmod-ila-flexi)#channel-id 1 centre-freq 196.1 width 75
RP/0/RP0/CPU0:ios(config-hwmod-ila-flexi)# commit

To create the OTS-OCH controller on the LINE side of an OLT-R-C node, use the following commands:

RP/0/RP0/CPU0:ios#config
RP/0/RP0/CPU0:ios(config)#hw-module location 0/0/nxr0 terminal-ampli grid-mode flex
RP/0/RP0/CPU0:ios(config-hwmod-olt-flexi)#channel-id 1 centre-freq 196.1 width 75
RP/0/RP0/CPU0:ios(config-hwmod-olt-flexi)#commit

interface

Use the interface command in the config mode to enter the configuration mode of a management interface. To delete the configuration, use the no form of this command.

interface type interface-path-id

no interface type interface-path-id

Syntax Description

type

Interface type.

interface-path-id

Physical interface or virtual interface.

Command Default

None

Command Modes

Configuration Mode

Command History

Release Modification

Release 24.2.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task ID's. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

otn

write

Examples

This example shows how to enter the configuration mode of mgmtEth interface:

RP/0/RP0/CPU0:Box(config)#interface mgmtEth0/RP0/CPU0/1 ​

ipv4-access-group

To control access to an interface, use the ipv4 access-group command in interface configuration mode. To remove the specified access group, use the no form of this command.

ipv4 access-group access-list-name { ingress | egress } [ compress level compression-level ]

Syntax Description

access-list-name

Name of an IPv4 access list as specified by an ipv4 access-list command.

ingress

Filters on inbound packets.

egress

Filters on outbound packets.

compress level compression-level

Configures compression level for interface ACLs. Compression level values range from zero and two.

Command Default

The interface does not have an IPv4 access list applied to it.

Command Modes

Interface configuration

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Use the ipv4 access-group command to control access to an interface. To remove the specified access group, use the no form of the command. Use the access-list-name argument to specify a particular IPv4 access list.

If the access list permits the addresses, the software continues to process the packet. If the access list denies the address, the software discards the packet and returns an Internet Control Message Protocol (ICMP) host unreachable message.

If the specified access list does not exist, all packets are passed.

Task ID

Task ID

Operations

acl

read, write

Examples

The following example shows how to apply the access list named IPV4-ACL to the management interface:


RP/0/RP0/CPU0:ios(config)# interface mgmtEth 0/RP0/CPU0/0
RP/0/RP0/CPU0:ios(config-if)# ipv4 access-group IPV4-ACL ingress
RP/0/RP0/CPU0:ios(config-if)# commit

ipv6-access-group

To control access to an interface, use the ipv6 access-group command in interface configuration mode. To remove the specified access group, use the no form of this command.

ipv6 access-group access-list-name { ingress | egress } [ compress level compression-level ]

Syntax Description

access-list-name

Name of an IPv6 access list as specified by an ipv6 access-list command.

ingress

Filters on inbound packets.

egress

Filters on outbound packets.

compress level compression-level

Configures compression level for interface ACLs. Compression level values range from zero and two.

Command Default

The interface does not have an IPv6 access list applied to it.

Command Modes

Interface configuration

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Use compression level two to create Hybrid ACLs with an ACE that uses IPv6 extension headers to filter ingress and egress IPv6 packets.

Task ID

Task ID

Operations

acl

read, write

Examples

The following example shows how to apply the access list named IPV6-ACL to the management interface:


RP/0/RP0/CPU0:ios(config)# interface mgmtEth 0/RP0/CPU0/0
RP/0/RP0/CPU0:ios(config-if)# ipv6 access-group IPV6-ACL ingress
RP/0/RP0/CPU0:ios(config-if)# commit

ipv4-access-list

To define an IPv4 access list by name, use the ipv4 access-list command in IOS XR Config mode. To remove all entries in an IPv4 access list, use the no form of this command.

ipv4 access-list name

no ipv4 access-list name

Syntax Description

name

Name of the access list. Names cannot contain a space or quotation marks.

Command Default

No IPv4 access list is defined.

Command Modes

IOS XR Config mode

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Use the ipv4 access-list command to configure an IPv4 access list. This command places the system in access list configuration mode, in which the denied or permitted access conditions must be defined with the deny or permit command.

Use the ipv4 access-group command to apply the access list to an interface.

Task ID

Task ID

Operations

acl

read, write

Examples

This example shows how to define a standard access list named ACL:


RP/0/RP0/CPU0:ios(config)# ipv4 access-list ACL
RP/0/RP0/CPU0:ios(config-ipv4-acl)# 10 permit tcp 192.0.2.2 255.255.255.0 any
RP/0/RP0/CPU0:ios(config-ipv4-acl)# 20 deny udp any any
RP/0/RP0/CPU0:ios(config-ipv4-acl)# 30 permit ipv4 192.0.2.64 255.255.255.0 any
RP/0/RP0/CPU0:ios(config-ipv4-acl)# commit

ipv6-access-list

To define an IPv6 access list by name, use the ipv6 access-list command in IOS XR Config mode. To remove all entries in an IPv6 access list, use the no form of this command.

ipv6 access-list name

no ipv6 access-list name

Syntax Description

name

Name of the access list. Names cannot contain a space or quotation mark, or begin with a numeric.

Command Default

No IPv6 access list is defined.

Command Modes

IOS XR Config mode

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

The IPv6 access lists are used for traffic filtering based on source and destination addresses, IPv6 option headers, and optional, upper-layer protocol type information for finer granularity of control. IPv6 access lists are defined by using the ipv6 access-list command in XR Config mode mode and their permit and deny conditions are set by using the deny and permit commands in IPv6 access list configuration mode. From IPv6 access list configuration mode, permit and deny conditions can be set for the defined IPv6 access list.

The ipv6 access-list command is similar to the ipv4 access-list command, except that it is IPv6-specific.

Use the ipv6 access-group command to apply the access list to an interface.

Every IPv6 access list has an implicit deny ipv6 any any statement as its last match condition. An IPv6 access list must contain at least one entry for the implicit deny ipv6 any any statement to take effect.

Task ID

Task ID

Operations

acl

read, write

Examples

This example shows how to define a standard access list named ACL:


RP/0/RP0/CPU0:ios(config)# ipv6 access-list ACL
RP/0/RP0/CPU0:ios(config-ipv6-acl)# 10 permit ipv6 any any
RP/0/RP0/CPU0:ios(config-ipv6-acl)# 20 deny udp any any
RP/0/RP0/CPU0:ios(config-ipv6-acl)# commit

ipv4 address

Use the ipv4 address command in the interface configuration mode to configure IPv4 address for an interface. To remove the IPv4 address from an interface, use the no form of this command.

ipv4 address

no ipv4 address

Command Default

None

Command Modes

Interface Configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

otn

write

Examples

This example shows how to configure IPv4 address on an interface.

RP/0/RP0/CPU0:Box(config-if)# ipv4 address 192.0.2.6/24 ​

Examples

This example shows how to remove IPv4 address from an interface.

RP/0/RP0/CPU0:Box(config-if)# no ipv4 address ​

ipv6 address

Use the ipv6 address command in the interface configuration mode to configure IPv6 address for an interface. To remove the IPv6 address from an interface, use the no form of this command.

ipv6 address

no ipv6 address

Command Default

None

Command Modes

Interface Configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

otn

write

Examples

This example shows how to configure IPv6 address on an interface.

RP/0/RP0/CPU0:Box(config-if)# ipv6 address 0:0:0:7272::72/64 ​

Examples

This example shows how to remove IPv6 address from an interface.

RP/0/RP0/CPU0:Box(config-if)# no ipv6 address ​

link-tuner

To enable and disable link tuner and to configure the spectrum density, use the link-tuner command.

link-tuner { enable | disable | spectrum-density value }

Syntax Description

enable

Enable Link-Tuner

disable

Disable Link-Tuner

spectrum-density

Configure spectrum density

value

Spectrum density in range 1–100 in increments of 1

Command Default

The default spectrum density is 81.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following is a sample configuration that enables link tuner.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control 
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#link-tuner enable
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

The following is a sample configuration that disables link tuner.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control 
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#link-tuner disable
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

The following example is a sample configuration that configures the spectrum density to 80%.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control 
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#link-tuner spectrum-density 80
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

license smart deregister

To cancel the registration of your device, use the license smart deregister command.

license smart deregister

Command Default

None

Command Modes

None

Command History

Release Modification
R7.7.1

This command was introduced.

Usage Guidelines

When your device is taken off the inventory, shipped elsewhere for redeployment or returned to Cisco for replacement using the return merchandise authorization (RMA) process, you can use this command to cancel the registration on your device. All smart licensing entitlements and certificates on the platform are removed.

Examples

The following example deregisters NCS 1010.

RP/0/RP0/CPU0:ios#license smart deregister

license smart register

To register the device instance with Cisco licensing cloud, use the license smart register idtoken token-id force command.

license smart register idtoken token-id [ force ]

Syntax Description

token_id

Specifies the token generated in smart manager.

force

If the registration fails due to communication failure between the device and the portal, the system waits for 24 hours before attempting to register the device again. Use this option to force the registration.

Command Default

None

Command Modes

None

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Use this command to register the device instance with Cisco licensing cloud.

Examples

The following example registers and sets the token ID required for registration of NCS 1004.

RP/0/RP0/CPU0:ios#license smart register YzY2ZjYyNjktY2NlOS00NTc4LWIxNTAtMjZkNmNiNzMxMTY1LTE2NjAzNjQ3
%0ANzY4Njl8ZVJSckxKN2pFV2tIeHVoMUkxbGxTazFDVm9kc1B5MGlHQmlFWUJi%0Ac3VNRT0%3D%0A  
        

license smart renew

To manually renew the ID certification or authorization, use the license smart renew command.

license smart renew { ID | auth }

Syntax Description

ID

ID certificates are renewed automatically after six months. In case, the renewal fails, the product instance goes into unidentified state. You can manually renew the ID certificate using this option.

auth

Authorization periods are renewed by the Smart Licensing system every 30 days. As long as the license is in an 'Authorized' or 'Out-of-compliance' (OOC), the authorization period is renewed. Use this command to make an on-demand manual update of your registration. Thus, instead of waiting 30 days for the next registration renewal cycle, you can use this option to instantly find out the status of your license.

After 90 days, the authorization period expires and the status of the associated licenses display "AUTH EXPIRED". Use this option to retry the authorization period renewal. If the retry is successful, a new authorization period begins.

Command Default

None

Command Modes

None

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

The following example manually renews the ID certificate for the NCS 1010:

RP/0/RP0:ios#license smart renew id
    

The following example manually renews the authorization for the NCS 1010:

RP/0/RP0:ios#license smart renew auth
          

license smart reservation install file

To register the device using the authorization code that is copied as a file, and to activate smart licensing reservation for your device, use the license smart reservation install file command.

license smart reservation install file file name

Syntax Description

file name

Name of the file where the authorization code is saved.

Command Default

None

Command Modes

None

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

The following example registers and activates the registration and license for NCS 1010:

RP/0/RP0/CPU0:ios#license smart reservation install file /disk0:/smart1
Tue Jul 19 13:46:22.877 UTC
RP/0/RP0/CPU0:Jul 19 13:46:22.946 UTC: plat_sl_client[368]: %LICENSE-PLAT_CLIENT-6-STATE_CHANGE :
Licensing platform state changing from UNREGISTERED to REGISTERED
RP/0/RP0/CPU0:Jul 19 13:46:22.946 UTC: smartlicserver[247]: %LICENSE-SMART_LIC-6-AGENT_REG_SUCCESS
: Smart Agent for Licensing Registration successful. udi PID:NCS1010-SA,SN:FCB2546B08T
Reservation install file successful
Last Confirmation code 8572aa81
    

license smart transport

To configure the smart transport as an alternative option to Call Home,use the license smart transport command.

license smart transport smart

Command Default

None

Command Modes

None

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

The following example configures the smart transport option to connect to the CSSM.

 RP/0/RP0/CPU0:ios#license smart transport smart 
        Thu Jul 19 13:34:47.251 UTC
        RP/0/RP0/CPU0:ios#commit
    

ntp

To enter Network Time Protocol (NTP) configuration mode and run NTP configuration commands, use the ntp command in global configuration mode.

ntp

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values.

Command Modes

Global configuration

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Task ID

Task ID

Operations

ip-services

read, write

Examples

The following example shows how to enter NTP configuration mode:


RP/0/RP0/CPU0:ios(config)#ntp
RP/0/RP0/CPU0:ios(config-ntp)#

olc bfr-initialize

Use the olc bfr-initialize command to initialize the Band Failure Recovery(BFR) feature.

olc bfr-initialize controller ots R/S/I/P

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OTS controller.

controller Ots

Use this parameter to choose a particular controller.

Command Modes

Privileged EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following is a sample output of the olc bfr-initialize command that initializes BFR.

RP/0/RP0/CPU0:ios#olc bfr-initialize controller ots 0/0/0/0 
 

olc bfr-pause

Use the olc bfr-pause command to enable or disable Band Failure Recovery(BFR) pause. In case of band failure, when BFR pause is enabled, the recovery procedure is not initiated and the surviving band is not switched to single-band PSD profile.

olc bfr-pause controller ots Rack/Slot/Instance/Port { enable | disable }

Syntax Description

controller Ots

Use this parameter to choose a particular controller.

R/S/I/P

Rack/Slot/Instance/Port of the OTS controller.

enable Use this keyword to temporarily pause BFR.
disable Use this keyword to disable BFR pause.

Command Modes

Privileged EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following is a sample output of the olc bfr-pause command that enables the BFR pause feature and temporarily pauses BFR.

RP/0/RP0/CPU0:ios#olc bfr-pause controller ots 0/0/0/0 enable
 

Examples

The following is a sample output of the olc bfr-pause command that disables the BFR pause feature.

RP/0/RP0/CPU0:ios#olc bfr-pause controller ots 0/0/0/0 disable
 

olc start-gain-estimation

Use the olc start-gain-estimation command to trigger the gain estimation operation.

olc start-gain-estimation controller ots R/S/I/P

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

controller Ots

Use this parameter to choose a particular controller.

Command Modes

Privileged EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following output is a sample of the olc start-gain-estimation controller ots 0/0/0/0 command.

RP/0/RP0/CPU0:ios#olc start-gain-estimation controller ots 0/0/0/0 

olc start-raman-tuning

Use the olc start-raman-tuning command to trigger Raman tuning.

olc start-raman-tuning controller ots R/S/I/P

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

controller Ots

Use this parameter to choose a particular controller.

Command Modes

Privileged EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

optical-line-control

To use the optical applications configuration mode, use the optical-line-control command.

optical-line-control

Command Modes

Global configuration mode (config)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

otdr auto-scan

Use the otdr auto-scan command to enable or disable the auto otdr scan

otdr auto-scan [ enable | disable ]

Syntax Description

enable

Enables OTDR auto scan.

disable

Disables OTDR auto scan.

Command Modes

Controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following are sample configurations that enable and disable automatic OTDR scan.

RP/0/RP0/CPU0:ios#configure
Mon Sep 18 13:11:53.812 UTC
RP/0/RP0/CPU0:IOS(config)#optical-line-control controller Ots 0/0/0/0
RP/0/RP0/CPU0:IOS(config-olc-ots)#otdr auto-scan enable 
RP/0/RP0/CPU0:IOS(config-olc-ots)#commit
RP/0/RP0/CPU0:ios#configure
Mon Sep 3 13:28:34.631 UTC
RP/0/RP0/CPU0:IOS(config)#optical-line-control controller Ots 0/0/0/0
RP/0/RP0/CPU0:IOS(config-olc-ots)#otdr auto-scan disable 
RP/0/RP0/CPU0:IOS(config-olc-ots)#commit

otdr start

Use the otdr-start controller ots command to start the otdr operation.

otdr-start controller ots R/S/I/P direction

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OTS controller.

otdr-start controller ots

Use this parameter to start the otdr operation in a particular direction.

direction

Scan direction (RX or TX)

Command Modes

Privileged EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following output is a sample of enabling and disabling automatic OTDR scan.

otdr stop

Use the otdr-stop controller ots command to stop the otdr operation.

otdr-stop controller ots R/S/I/P direction

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OTS controller.

otdr-stop controller ots

Use this parameter to stop the otdr operation in a particular direction.

direction

Scan direction (RX or TX)

Command Modes

Privileged EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

RP/0/RP0/CPU0:ios#otdr-stop controller ots 0/0/0/0 tx 
OTS OTDR Scan Stopped at TX

partner-band-port

Use the partner-band-port command to establish a connection between C and L-band nodes by configuring the L-band peer IP on C-band node and C-band peer IP on L-band node.

partner-band-port ipv4 address controller ots Rack/Slot/Instance/Port

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OTS controller.

ipv4 address

Specify the IP address of the peer node.

controller Ots

Use this parameter to choose a particular controller.

R/S/I/P

Rack/Slot/Instance/Port of the OTS controller.

Command Modes

Privileged EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Example 1

The following is a sample output of the partner-band-port command that configures the peer node IP address 192.0.2.1 on the C-band node.

RP/0/RP0/CPU0:ios# optical-line-control controller Ots0/0/0/0
RP/0/RP0/CPU0:ios# partner-band-port ipv4 address 192.0.2.1 controller Ots0/0/0/0 

 

pm

To configure the performance monitoring parameters of the OTS, OTS-OCH, OSC, and DFB controllers, use the pm command in the controller configuration mode.

For more information about PM threshold values for the controllers, see the section, Monitor performance.

pm [ flex-bin | 15-min | 30-sec | 24-hour ] [ ots | ots-och | osc | dfb ] [ report | threshold ] [ eagn | eatl | iagn | iatl | slr-cl | slt-cl | opbr | opr | opr-cl | opt | opt-s | raman-1 | raman-2 | raman-3 | raman-4 | raman-5 | raman-tot ] [ max-tca | min-tca ] [ enable | value ]

Syntax Description

flex-bin| 15-min | 30-sec | 24-hour

Configures performance monitoring parameters for 10 seconds, 15 minutes, 30 seconds, or 24-hour intervals.

ots | ots-och | osc | dfb

Specifies whether to configure performance monitoring parameters for the OTS, OTS-OCH, OSC, or DFB controllers.

history

Displays the historical values of the pm command.

report

Configures the TCA reporting status for optics (OTS-OCH, OSC, or DFB) or OTS parameters.

threshold

Configures thresholds on optics (OTS-OCH, OSC, or DFB) or OTS parameters.

iagn | eagn

Configures thresholds for ingress or egress amplifier gain.

iatl |eatl

Configures the thresholds for ingress or egress amplifier tilt.

slr-cl | slt-cl

Configures the thresholds for span loss in Rx or Tx direction.

opr | opr-cl |opr-s

Configures thresholds for total Rx power, total Rx power for C and L band, or total C band signal power.

opbr

Configures thresholds for back reflection power.

opt |opt-s

Configures thresholds for total Tx power or total C band signal power.

raman-1 | raman-2 | raman-3 | raman-4 | raman-5 | raman-tot

Configures thresholds for Raman power (1, 2, 3, 4, or 5) or total Raman pump power.

max-tca | min-tca enable

Enable the maximum or minimum TCA reporting status.

value

Value of the thresholds.

Command Default

None

Command Modes

Controller configuration

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

The following examples shows how to view the configured maximum and minimum threshold values and the current span loss values for both Tx and Rx direction.

RP/0/RP0/CPU0:ios#show controllers ots 0/0/0/0 pm current 15-min optics 1

Optics in the current interval [06:30:00 - 06:37:00 Tue May 17 2022]

Optics current bucket type : Valid
               MIN       AVG       MAX     Operational  Configured    TCA   Operational   Configured  TCA
                                        Threshold(min)Threshold(min(min) Threshold(max)Threshold(max(max)
OPT[dBm]      : 20.00     20.00     20.00    -20.00    NA           NO   40.00         NA           NO
OPR[dBm]      : 20.00     20.00     20.00    -30.00    NA           NO   18.00         NA           NO
OPT(C+L)[dBm] : 20.00     20.00     20.00    -20.00    NA           NO   60.85         NA           NO
OPR(C+L)[dBm] : -10.00    -10.00    -10.00   -30.00    NA           NO   36.00         NA           NO
OPT(S)[dBm]   : 20.00     20.00     20.00    -5.00     NA           NO   28.00         NA           NO
OPR(S)[dBm]   : 20.00     20.00     20.00    -30.00    NA           NO   18.00         NA           NO
OPBR[dBm]     : -30.00    -30.00    -30.00   -30.00    NA           NO   -14.09        NA           NO
EAGN[dB]      : 30.00     30.00     30.00    16.00     NA           NO   20.00         20.00        YES
SLR(C+L)[dB]  : 4.46      4.49      4.50     0.00      NA           NO   42.00         NA           NO
SLT(C+L)[dB]  : 0.09      0.09      0.09     0.00      NA           NO   42.00         NA           NO
EATL[dB]      : -4.80     -4.80     -4.80    -5.00     NA           NO   5.00          NA           NO
IAGN[dB]      : 25.00     25.00     25.00    12.00     NA           NO   25.00         NA           NO
IATL[dB]      : -2.40     -2.40     -2.40    -5.00     NA           NO   5.00          NA           NO
RAMAN-TOT[mW] : 300.00    300.00    300.00   200.00    NA           NO   1410.00       NA           NO
RAMAN-1 [mW]  : 45.00     45.00     45.00    45.00     NA           NO   390.00        NA           NO
RAMAN-2 [mW]  : 40.00     40.00     40.00    40.00     NA           NO   390.00        NA           NO
RAMAN-3 [mW]  : 40.00     40.00     40.00    40.00     NA           NO   220.00        NA           NO
RAMAN-4 [mW]  : 40.00     40.00     40.00    40.00     NA           NO   220.00        NA           NO
RAMAN-5 [mW]  : 35.00     35.00     35.00    35.00     NA           NO   190.00        NA           NO

Last clearing of "show controllers OPTICS" counters never

The following sample sets the reporting status to maximum TCA for the eagn parameter of the OTS controller for a 15-minute interval.


RP/0/RP0/CPU0:ios#config
RP/0/RP0/CPU0:ios(config)#controller ots 0/0/0/0 pm 15-min ots report eagn max-tca enable
 RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)#end

The following sample configures the maximum threshold for the eagn parameter of the OTS controller to 20 dB.

RP/0/RP0/CPU0:ios#config
RP/0/RP0/CPU0:ios(config)#controller ots 0/0/0/0 pm 15-min ots threshold eagn max 2000
RP/0/RP0/CPU0:ios(config)#commit
RP/0/RP0/CPU0:ios(config)#end

To view the current PM parameters on an OTS controller for a 15 minute interval, use the following command:


RP/0/RP0/CPU0:ios#sh controllers ots 0/0/0/0 pm current 15-min optics 1
Tue May 17 06:37:00.529 UTC

Optics in the current interval [06:30:00 - 06:37:00 Tue May 17 2022]

Optics current bucket type : Valid
             MIN       AVG       MAX     Operational  Configured    TCA   Operational   Configured  TCA
                                        Threshold(min)Threshold(min(min) Threshold(max)Threshold(max(max)
OPT[dBm]     : 20.00     20.00     20.00    -20.00     NA           NO   40.00         NA           NO
OPR[dBm]     : 20.00     20.00     20.00    -30.00     NA           NO   18.00         NA           NO
OPT(C+L)[dBm] : 20.00     20.00     20.00    -20.00    NA           NO   60.85         NA           NO
OPR(C+L)[dBm] : -10.00    -10.00    -10.00   -30.00    NA           NO   36.00         NA           NO
OPT(S)[dBm]   : 20.00     20.00     20.00    -5.00     NA           NO   28.00         NA           NO
OPR(S)[dBm]   : 20.00     20.00     20.00    -30.00    NA           NO   18.00         NA           NO
OPBR[dBm]     : -30.00    -30.00    -30.00   -30.00    NA           NO   -14.09        NA           NO
EAGN[dB]      : 30.00     30.00     30.00    16.00     NA           NO   20.00         20.00        YES
EATL[dB]      : -4.80     -4.80     -4.80    -5.00     NA           NO   5.00          NA           NO
IAGN[dB]      : 25.00     25.00     25.00    12.00     NA           NO   25.00         NA           NO
IATL[dB]      : -2.40     -2.40     -2.40    -5.00     NA           NO   5.00          NA           NO
RAMAN-TOT[mW] : 300.00    300.00    300.00   200.00    NA           NO   1410.00       NA           NO
RAMAN-1 [mW]  : 45.00     45.00     45.00    45.00     NA           NO   390.00        NA           NO
RAMAN-2 [mW]  : 40.00     40.00     40.00    40.00     NA           NO   390.00        NA           NO
RAMAN-3 [mW]  : 40.00     40.00     40.00    40.00     NA           NO   220.00        NA           NO
RAMAN-4 [mW]  : 40.00     40.00     40.00    40.00     NA           NO   220.00        NA           NO
RAMAN-5 [mW]  : 35.00     35.00     35.00    35.00     NA           NO   190.00        NA           NO

Last clearing of "show controllers OPTICS" counters never

To view the historical PM parameters on an OTS controller for a 15 minute interval, use the following command:

RP/0/RP0/CPU0:ios#sh controllers ots 0/0/0/0 pm history 15-min optics  1 bucket 1
Tue May 17 07:02:26.911 UTC

Optics in interval 1 [06:45:00 - 07:00:00 Tue May 17 2022]

Optics history bucket type : Valid
                MIN       AVG       MAX
OPT[dBm]   :   20.00      20.00     20.00
OPR[dBm]   :   20.00      20.00     20.00
OPT(C+L)[dBm]: 20.00      20.00     20.00
OPR(C+L)[dBm]: -10.00    -10.00    -10.00
OPT(S)[dBm]  : 20.00      20.00     20.00
OPR(S)[dBm]  : 20.00      20.00     20.00
OPBR[dBm]    : -30.00    -30.00    -30.00
EAGN[dB]     : 30.00     30.00     30.00
EATL[dB]     : -4.80     -4.80     -4.80
IAGN[dB]     : 25.00     25.00     25.00
IATL[dB]     : -2.40     -2.40     -2.40
RAMAN-TOT[mW]: 300.00    300.00    300.00
RAMAN-1 [mW] : 45.00     45.00     45.00
RAMAN-2 [mW] : 40.00     40.00     40.00
RAMAN-3 [mW] : 40.00     40.00     40.00
RAMAN-4 [mW] : 40.00     40.00     40.00
RAMAN-1 [mW] : 35.00     35.00     35.00

To view the current PM parameters on an OTS-OCH controller for a 15 minute interval, use the following command:

P/0/RP0/CPU0:ios#sh controllers ots-och 0/0/0/0/1 pm current 15-min optics 1
Tue May 17 10:27:20.387 UTC

Optics in the current interval [10:15:00 - 10:27:20 Tue May 17 2022]

Optics current bucket type : Valid
           MIN  AVG   MAX Operational    Configured      TCA      Operational    Configured     TCA
                          Threshold(min)  Threshold(min) (min)   Threshold(max)   Threshold(max) (max)
OPT[dBm] : 1.20 1.30   1.30     -30.00            NA            NO         15.00         NA      NO
OPR[dBm] :-12.31-12.25-12.20     -30.00           NA            NO         15.00         NA      NO
Last clearing of "show controllers OPTICS" counters never

To view the current PM parameters on an OSC controller for a 15 minute interval, use the following command:

RP/0/RP0/CPU0:ios#sh controller osc 0/0/0/0 pm current 15-min optics 1
Tue May 17 08:24:32.642 UTC

Optics in the current interval [08:15:00 - 08:24:32 Tue May 17 2022]

Optics current bucket type : Valid
             MIN       AVG       MAX      Operational      Configured      TCA   Operational Configured     TCA
                                          Threshold(min)   Threshold(min) (min) Threshold(max)Threshold(max)(max)
OPT[dBm]     : -10.00    -10.00    -10.00   -20.00            NA           NO   12.00            NA           NO
OPR[dBm]     : -30.00    -30.00    -30.00   -30.00            NA           NO   0.00             NA           NO

Last clearing of "show controllers OPTICS" counters never

To view the current PM parameters on an DFB controller for a 15 minute interval, use the following command:

RP/0/RP0/CPU0:ios#sh controller dfb 0/0/0/0 pm current 15-min optics 1
Tue May 17 08:28:37.455 UTC

Optics in the current interval [08:15:00 - 08:28:37 Tue May 17 2022]

Optics current bucket type : Valid
          MIN   AVG  MAX   Operational Configured    TCA   Operational Configured     TCA
                           Threshold  Threshold            Threshold    Threshold
                             (min)      (min)        (min)    (max)         (max)     (max)
OPT[dBm]: 20.00 20.00 20.00   -25.23     NA         NO    18.00            NA          NO
OPR[dBm]: 10.00 10.00 10.00   -30.00     NA         NO    12.00            NA          NO

Last clearing of "show controllers OPTICS" counters never

To view the current PM parameters for an OCH controller for a 30-second interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers och 0/1/0/0 pm current 30-sec optics 1
Tue May 10 11:28:29.896 UTC

Optics in the current interval [11:28:00 - 11:28:29 Tue May 10 2022]

Optics current bucket type : Valid
             MIN       AVG       MAX      Operational      Configured      TCA   Operational      Configured     TCA
                                          Threshold(min)   Threshold(min) (min) Threshold(max)   Threshold(max) (max)
OPT[dBm]     : -50.00    -50.00    -50.00   -30.00            NA              NO   15.00            NA              NO
OPR[dBm]     : -50.00    -50.00    -50.00   -30.00            NA              NO   15.00            NA              NO

Last clearing of "show controllers OPTICS" counters never

To view the historical PM parameters on an OCH controller for a 30-second interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers och 0/1/0/0 pm history 30-sec optics 1 bucket 1

Mon Jul 25 05:35:52.176 UTC

Optics in interval 1 [05:35:00 - 05:35:30 Mon Jul 25 2022]

Optics history bucket type : Valid
              MIN       AVG       MAX
OPT[dBm]   : -50.00    -50.00    -50.00
OPR[dBm]   : -50.00    -50.00    -50.00

Last clearing of "show controllers OPTICS" counters never

To view the current PM parameters for an OCH controller for a 15-minute interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers och 0/1/0/0 pm current 15-min optics 1
Tue May 10 11:28:50.952 UTC

Optics in the current interval [11:15:00 - 11:28:50 Tue May 10 2022]

Optics current bucket type : Valid
             MIN       AVG       MAX      Operational      Configured      TCA   Operational      Configured     TCA
                                          Threshold(min)   Threshold(min) (min) Threshold(max)   Threshold(max) (max)
OPT[dBm]     : -50.00    -50.00    -50.00   -30.00            NA              NO   15.00            NA              NO
OPR[dBm]     : -50.00    -50.00    -50.00   -30.00            NA              NO   15.00            NA              NO

Last clearing of "show controllers OPTICS" counters never

To view the historical PM parameters for an OCH controller for a 15-minute interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers och 0/1/0/0 pm history 15-min optics 1 bucket 1

Mon Jul 25 05:36:12.167 UTC

Optics in interval 1 [05:15:00 - 05:30:00 Mon Jul 25 2022]

Optics history bucket type : Valid
              MIN       AVG       MAX
OPT[dBm]   : -50.00    -50.00    -50.00
OPR[dBm]   : -50.00    -50.00    -50.00

Last clearing of "show controllers OPTICS" counters never

To view the current PM parameters on an OCH controller for a 24-hour interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers och 0/1/0/0 pm current 24-hour optics 1
Tue May 10 11:29:09.270 UTC

Optics in the current interval [00:00:00 - 11:29:09 Tue May 10 2022]

Optics current bucket type : Invalid
             MIN       AVG       MAX      Operational      Configured      TCA   Operational      Configured     TCA
                                          Threshold(min)   Threshold(min) (min) Threshold(max)   Threshold(max) (max)
OPT[dBm]     : -50.00    -50.00    -50.00   -30.00            NA              NO   15.00            NA              NO
OPR[dBm]     : -50.00    -50.00    -50.00   -30.00            NA              NO   15.00            NA              NO

Last clearing of "show controllers OPTICS" counters never
RP/0/RP0/CPU0:ios#

To view the historical PM parameters on an OCH controller for a 24-hour interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers och 0/1/0/0 pm history 24-hour optics 1

Mon Jul 25 05:36:35.165 UTC

Optics in interval 1 [00:00:00 - 24:00:00 Sun Jul 24 2022]

Optics history bucket type : Valid
              MIN       AVG       MAX
OPT[dBm]   : -50.00    -50.00    -50.00
OPR[dBm]   : -50.00    -50.00    -50.00

Last clearing of "show controllers OPTICS" counters never

To view the current PM parameters for an OMS controller for a 30-second interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers oms 0/3/0/8 pm current 30-sec optics 1

Mon Jul 25 07:24:38.319 UTC

Optics in the current interval [07:24:30 - 07:24:38 Mon Jul 25 2022]

Optics current bucket type : Valid
MIN AVG MAX Operational Configured TCA Operational Configured TCA
Threshold(min) Threshold(min) (min) Threshold(max) Threshold(max) (max)
OPT[dBm] : -50.00 -50.00 -50.00 -30.00 NA NO 15.00 NA NO
OPR[dBm] : -50.00 -50.00 -50.00 -30.00 NA NO 15.00 NA NO

Last clearing of "show controllers OPTICS" counters never

To view the historical PM parameters on an OMS controller for a 30-second interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers oms 0/3/0/8  pm history 30-sec optics 1 bucket 1

Mon Jul 25 07:13:51.228 UTC

Optics in interval 1 [07:13:00 - 07:13:30 Mon Jul 25 2022]

Optics history bucket type : Valid
              MIN       AVG       MAX
OPT[dBm]   : -50.00    -50.00    -50.00
OPR[dBm]   : -50.00    -50.00    -50.00

Last clearing of "show controllers OPTICS" counters never

To view the current PM parameters for an OMS controller for a 15-minute interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers oms 0/3/0/8 pm current 15-min optics 1

Mon Jul 25 07:25:00.183 UTC

Optics in the current interval [07:15:00 - 07:25:00 Mon Jul 25 2022]

Optics current bucket type : Valid
MIN AVG MAX Operational Configured TCA Operational Configured TCA
Threshold(min) Threshold(min) (min) Threshold(max) Threshold(max) (max)
OPT[dBm] : -50.00 -50.00 -50.00 -30.00 NA NO 15.00 NA NO
OPR[dBm] : -50.00 -50.00 -50.00 -30.00 NA NO 15.00 NA NO

Last clearing of "show controllers OPTICS" counters never

To view the historical PM parameters for an OMS controller for a 15-minute interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers oms 0/3/0/8  pm history 15-min optics 1 bucket 1

Mon Jul 25 07:14:03.090 UTC

Optics in interval 1 [06:45:00 - 07:00:00 Mon Jul 25 2022]

Optics history bucket type : Valid
              MIN       AVG       MAX
OPT[dBm]   : -50.00    -50.00    -50.00
OPR[dBm]   : -50.00    -50.00    -50.00

Last clearing of "show controllers OPTICS" counters never

To view the current PM parameters on an OMS controller for a 24-hour interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers oms 0/3/0/8 pm current 24-hour optics 1

Mon Jul 25 07:26:09.817 UTC

Optics in the current interval [00:00:00 - 07:26:09 Mon Jul 25 2022]

Optics current bucket type : Valid
MIN AVG MAX Operational Configured TCA Operational Configured TCA
Threshold(min) Threshold(min) (min) Threshold(max) Threshold(max) (max)
OPT[dBm] : -50.00 -50.00 -50.00 -30.00 NA NO 15.00 NA NO
OPR[dBm] : -50.00 -50.00 -50.00 -30.00 NA NO 15.00 NA NO

Last clearing of "show controllers OPTICS" counters never

To view the historical PM parameters on an OMS controller for a 24-hour interval, use the following command:

RP/0/RP0/CPU0:ios#show controllers oms 0/3/0/8 pm history 24-hour optics 1

Mon Jul 25 07:18:13.532 UTC

Optics in interval 1 [00:00:00 - 24:00:00 Sun Jul 24 2022]

Optics history bucket type : Valid
              MIN       AVG       MAX
OPT[dBm]   : -50.00    -50.00    -50.00
OPR[dBm]   : -50.00    -50.00    -50.00

Last clearing of "show controllers OPTICS" counters never

process restart

To restart the license registration process, use the license smart reservation command.

process restart smartlicserver location location

Syntax Description

location

Specifies the node-id.

Command Default

None

Command Modes

None

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

The following example restarts the smart licensing process:

 RP/0/RP0/CPU0:ios#RP/0/RP0/CPU0:ios(config)#process restart smartlicserver location 0/RP0/CPU0
    

psd

Use the psd command to set the target PSDs.

psd index value

Syntax Description

index

PSD index 1–33.

value

PSD in range -30.0 dBm per 12.5 GHz to 23.0 dBm per 12.5 GHz in increments of 0.1 dBm per 12.5 GHz.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

You can configure the target power spectral densities for 33 points across the band. The 33 PSD values divide the entire spectrum into 150-GHz steps. APC uses the corresponding PSD value if the channel frequency corresponds to a configured point. If the central frequency is not on a configured position, APC computes the target PSD for a channel by extrapolating from the two adjacent steps.

Examples

The following is a sample configuration that sets the psd to 15 dB for the setpoints 1 and 2.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#psd 1 150
RP/0/RP0/CPU0:ios(config-olc-ots)#psd 2 150
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

psd-min

Use the psd-min command to set the desired minimum PSD.

psd-min value

Syntax Description

value

PSD in range -40.0 dBm per 12.5 GHz to 23.0 dBm per 12.5 GHz in increments of 0.1 dBm per 12.5 GHz.

Command Default

The default minimum PSD is –24 dB.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following is a sample configuration that sets the minimum PSD to –25 dB.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#psd-min -250
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
Tue Apr 26 09:50:12.055 UTC
RP/0/RP0/CPU0:ios(config-olc-ots)#end

reload

To perform the reload operation on the NCS 1010 unit and its modules, use the reload command.

reload location location

Syntax Description

location | location

(Optional) Enter the location for the unit or module which you want to reload.

Command Default

All slots are reloaded.

Command Modes

Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

To reboot the Cisco NCS 1010 system, use the following command.

RP/0/RP0/CPU0:ios#reload
Fri Apr 29 06:50:12.312 UTC
Proceed with reload? [confirm]
RP/0/RP0/CPU0:ios#
Preparing system for backup. This may take a few minutes especially for large configurations.
Status report: node0_RP0_CPU0: BACKUP INPROGRESS
Status report: node0_RP0_CPU0: BACKUP HAS COMPLETED SUCCESSFULLY
[Done]

To reboot the entire Cisco NCS 1010 system along with its modules, use the following command.

RP/0/RP0/CPU0:ios#reload location all noprompt
Fri Jul 15 14:53:25.775 UTC
RP/0/RP0/CPU0:ios#yes
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios#
********Completed Card Reload of all ********
##### Rack reload : all######
################# Iteration under Test : 7 #############
Waiting for 1000 seconds...
Waiting for 990 seconds...
Waiting for 980 seconds...
Waiting for 970 seconds...
.
.
output snipped
.
.
Waiting for 110 seconds...
Waiting for 100 seconds...
Waiting for 90 seconds...
Waiting for 80 seconds...
Waiting for 70 seconds...
Waiting for 60 seconds...
Waiting for 50 seconds...
Waiting for 40 seconds...
Waiting for 30 seconds...
Waiting for 20 seconds...
Waiting for 10 seconds...
XR Prompt =  RP/0/RP0/CPU0:P2A_DT_08#
Login sucessfull

type is <class 'telnetlib.Telnet'>
clear logging
Fri Jul 15 15:10:17.840 UTC
Clear logging buffer [confirm]
[y/n] :y
RP/0/RP0/CPU0:ios#
********XR Logging Cleared********
********Started Sanity Verification Tests ********
The term length 0 op is term length 0
Fri Jul 15 15:10:17.925 UTC

To reboot the Cisco NCS 1010 RP, use the following command.

RP/0/RP0/CPU0:ios#reload location 0/RP0 noprompt
Fri Jul 15 18:21:13.785 UTC
RP/0/RP0/CPU0:ios#yes
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios#
********Completed Card Reload of 0/RP0 ********
##### Rack reload : 0/RP0######
################# Iteration under Test : 1 #############
Waiting for 900 seconds...
Waiting for 890 seconds...
.
.
output snipped
.
.
Waiting for 110 seconds...
Waiting for 100 seconds...
Waiting for 90 seconds...
Waiting for 80 seconds...
Waiting for 70 seconds...
Waiting for 60 seconds...
Waiting for 50 seconds...
Waiting for 40 seconds...
Waiting for 30 seconds...
Waiting for 20 seconds...
Waiting for 10 seconds...
XR Prompt =  RP/0/RP0/CPU0:ios#
Login sucessfull

type is <class 'telnetlib.Telnet'>
clear logging
Fri Jul 15 18:36:25.996 UTC
Clear logging buffer [confirm]
[y/n] :y
RP/0/RP0/CPU0:ios#
********XR Logging Cleared********
********Started Sanity Verification Tests ********
The term length 0 op is term length 0
Fri Jul 15 18:36:26.062 UTC
RP/0/RP0/CPU0:ios#reload location 0/0/NXR0 noprompt
Sat Jul 16 05:03:51.547 UTC
RP/0/RP0/CPU0:ios#yes
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios#
********Completed Card Reload of 0/0/NXR0 ********
##### Rack reload : 0/0/NXR0######
################# Iteration under Test : 1 #############
Waiting for 900 seconds...
Waiting for 890 seconds...
Waiting for 880 seconds...
Waiting for 870 seconds...
.
.
output snipped
.
.
Waiting for 40 seconds...
Waiting for 30 seconds...
Waiting for 20 seconds...
Waiting for 10 seconds...
XR Prompt =  RP/0/RP0/CPU0:ios#
Login sucessfull

type is <class 'telnetlib.Telnet'>
clear logging
Sat Jul 16 05:19:03.274 UTC
Clear logging buffer [confirm]
[y/n] :y\
RP/0/RP0/CPU0:ios#
********XR Logging Cleared********
********Started Sanity Verification Tests ********
The term length 0 op is term length 0
Sat Jul 16 05:19:03.350 UTC

To warm reboot the Cisco NCS 1010 line card, use the following command.

RP/0/RP0/CPU0:ios#reload location 0/0 noprompt
Fri Jul 15 23:42:33.536 UTC
RP/0/RP0/CPU0:ios#yes
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios#
********Completed Card Reload of 0/0 ********
##### Rack reload : 0/0######
################# Iteration under Test : 1 #############
Waiting for 900 seconds...
Waiting for 890 seconds...
Waiting for 880 seconds...
Waiting for 870 seconds...
.
.
output snipped
.
.
Waiting for 80 seconds...
Waiting for 70 seconds...
Waiting for 60 seconds...
Waiting for 50 seconds...
Waiting for 40 seconds...
Waiting for 30 seconds...
Waiting for 20 seconds...
Waiting for 10 seconds...
XR Prompt =  RP/0/RP0/CPU0:ios#
Login sucessfull

type is <class 'telnetlib.Telnet'>
clear logging
Fri Jul 15 23:57:45.284 UTC
Clear logging buffer [confirm]
[y/n] :y
RP/0/RP0/CPU0:ios#
********XR Logging Cleared********
********Started Sanity Verification Tests ********
The term length 0 op is term length 0
Fri Jul 15 23:57:45.348 UTC

To warm reboot the Cisco NCS 1010 RP card, use the following command.

RP/0/RP0/CPU0:ios#reload location 0/RP0/CPU0 noprompt
Sat Jul 16 10:25:10.102 UTC
RP/0/RP0/CPU0:ios#yes
% Invalid input detected at '^' marker.
RP/0/RP0/CPU0:ios#
********Completed Card Reload of 0/RP0/CPU0 ********
##### Rack reload : 0/RP0/CPU0######
################# Iteration under Test : 1 #############
Waiting for 900 seconds...
Waiting for 890 seconds...
Waiting for 880 seconds...
Waiting for 870 seconds...
Waiting for 860 seconds...

.
.
output snipped
.
.
Waiting for 70 seconds...
Waiting for 60 seconds...
Waiting for 50 seconds...
Waiting for 40 seconds...
Waiting for 30 seconds...
Waiting for 20 seconds...
Waiting for 10 seconds...
XR Prompt =  RP/0/RP0/CPU0:P2A_DT_08#
Login sucessfull

type is <class 'telnetlib.Telnet'>
clear logging
Sat Jul 16 10:40:22.211 UTC
Clear logging buffer [confirm]
[y/n] :y
RP/0/RP0/CPU0:ios#
********XR Logging Cleared********
********Started Sanity Verification Tests ********
The term length 0 op is term length 0
Sat Jul 16 10:40:22.292 UTC

server

To allow the system clock to be synchronized by a NTP time server, use the server command in one of the NTP configuration modes. To remove the server command from the configuration file and restore the system to its default condition with respect to this command, use the no form of this command.

server [ ipv4 | ipv6 ] ip-address [ version number ] [ key key-id ] [ minpoll interval ] [ maxpoll interval ] [ source type interface-path-id ] [prefer] [burst] [iburst]

no server [ ipv4 | ipv6 ] ip-address

Syntax Description

ipv4

(Optional) Specifies an IPv4 IP address.

ipv6

(Optional) Specifies an IPv6 IP address.

ip-address

IPv4 or IPv6 address of the time server providing the clock synchronization.

version number

(Optional) Defines the Network Time Protocol (NTP) version number, where the number argument is a value from 1 to 4. The default is 4.

key key-id

(Optional) Defines the authentication key, where the key-id argument is the authentication key to use when packets are sent to this peer. By default, no authentication key is used.

minpoll interval

(Optional) Defines the shortest polling interval, where the interval argument is specified in powers of two seconds. Range is from 4 to 17. The default value is 6.

maxpoll interval

(Optional) Defines the longest polling interval, where the interval argument is specified in powers of two seconds. Range is from 4 to 17. The default value is 10.

source

(Optional) Specifies the IP source address. The default is the outgoing interface.

type

(Optional) Interface type. For more information, use the question mark ( ? ) online help function.

interface-path-id

(Optional) Physical interface or virtual interface.

Note

 

Use the show interfaces command to see a list of all interfaces currently configured on the device.

prefer

(Optional) Makes this peer the preferred server that provides synchronization.

burst

(Optional) Sends a series of packets instead of a single packet within each synchronization interval to achieve faster synchronization.

iburst

(Optional) Sends a series of packets instead of a single packet within the initial synchronization interval to achieve faster initial synchronization.

Command Default

No servers are configured by default.

Command Modes

NTP configuration

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

The value for the minpoll keyword must be less than or equal to the value for the maxpoll keyword. If this is not the case, the system issues an error message.

Using the prefer keyword reduces switching back and forth among servers.

Task ID

Task ID

Operations

ip-services

read, write

Examples

The following example shows how to configure the device to allow its system clock to be synchronized with the clock of the peer at IP address 203.0.113.51 using NTP.


RP/0/RP0/CPU0:ios(config)#ntp
RP/0/RP0/CPU0:ios(config-ntp)#server 203.0.113.51 minpoll 8 maxpoll 12 prefer iburst

show access-lists-ipv4

To display the contents of current IPv4 access lists, use the show access-lists ipv4 command in IOS XR EXEC mode.

show access-lists ipv4 [ access-list-name hardware { ingress | egress } [ interface type interface-path-id ] { sequence number | location node-id | [ usage pfilter { location node-id } ] } ]

Syntax Description

access-list-name

(Optional) Name of a particular IPv4 access list. The name cannot contain spaces or quotation marks, but can include numbers.

hardware

(Optional) Identifies the access list as an access list for an interface.

ingress

(Optional) Specifies an inbound interface.

interface

(Optional) Displays interface statistics.

type

(Optional) Interface type.

interface-path-id

Physical interface or virtual interface.

Note

 

Use the show interfaces command to see a list of all interfaces currently configured on the router.

sequence number

(Optional) Sequence number of a particular IPv4 access list. Range is 1 to 2147483644.

location node-id

(Optional) Location of a particular IPv4 access list. The node-id argument is entered in the rack/slot/module notation.

summary

(Optional) Displays a summary of all current IPv4 access lists.

sequence-number

(Optional) Sequence number of a particular IPv4 access list. Range is 1 to 2147483644.

usage

(Optional) Displays the usage of the access list on a given line card.

pfilter

(Optional) Displays the packet filtering usage for the specified line card.

Command Default

The default displays all IPv4 access lists.

Command Modes

IOS XR EXEC

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Use the show access-lists ipv4 command to display the contents of all IPv4 access lists. To display the contents of a specific IPv4 access list, use the name argument. Use the sequence-number argument to specify the sequence number of the access list.

Use the hardware , ingress and location keywords to display the access list hardware contents and counters for all interfaces that use the specified access list in a given direction. To display the contents of a specific access list entry, use the sequence number keyword and argument. The access group for an interface must be configured using the ipv4 access-group command for access list hardware counters to be enabled.

Use the show access-lists ipv4 summary command to display a summary of all current IPv4 access lists. To display a summary of a specific IPv4 access list, use the name argument.

Use the show access-list ipv4 usage command to display a summary of all interfaces and access lists programmed on the specified line card.

Task ID

Task ID

Operations

acl

read

Examples

In the following example, the contents of all IPv4 access lists are displayed:


RP/0/RP0/CPU0:ios# show access-lists ipv4 acl_1
Fri Oct 20 06:22:17.223 UTC
ipv4 access-list acl_1
10 permit ipv4 172.16.0.0 0.0.255.255 any
20 deny ipv4 192.168.34.0 0.0.0.255 any

show access-lists ipv6

To display the contents of current IPv6 access lists, use the show access-lists ipv6 command in IOS XR EXEC mode.

show access-lists ipv6 [ access-list-name hardware { ingress | egress } [ interface type interface-path-id ] { sequence number | location node-id | [ usage pfilter { location node-id } ] } ]

Syntax Description

access-list-name

(Optional) Name of a particular IPv6 access list. The name cannot contain a spaces or quotation marks, but can include numbers.

hardware

(Optional) Identifies the access list as an access list for an interface.

ingress

(Optional) Specifies an inbound interface.

interface

(Optional) Displays interface statistics.

type

(Optional) Interface type.

interface-path-id

(Optional) Either a physical interface instance or a virtual interface instance as follows:

  • Physical interface instance. Naming notation is rack/slot/instance/port and a slash between values is required as part of the notation.

    • rack: Chassis number of the rack.

    • slot: Physical slot number of the modular services card or line card.

    • instance: Module number.

    • port: Physical port number of the interface.

  • Virtual interface instance. Number range varies depending on interface type.

sequence number

(Optional) Sequence number of a particular IPv6 access list. Range is 1 to 2147483644.

location node-id

(Optional) Location of a particular IPv6 access list. The node-id argument is entered in the rack/slot/instance notation.

summary

(Optional) Displays a summary of all current IPv6 access lists.

sequence-number

(Optional) Sequence number of a particular IPv6 access list. Range is 1 to 2147483644.

usage

(Optional) Displays the usage of the access list on a given line card.

pfilter

(Optional) Displays the packet filtering usage for the specified line card.

all

(Optional) Displays the location of all the line cards.

Command Default

Displays all IPv6 access lists.

Command Modes

IOS XR EXEC

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

The show access-lists ipv6 command is similar to the show access-lists ipv4 command, except that it is IPv6 specific.

Use the show access-lists ipv6 command to display the contents of all IPv6 access lists. To display the contents of a specific IPv6 access list, use the name argument. Use the sequence-number argument to specify the sequence number of the access list.

Use the hardware , ingress and location keywords to display the access list hardware contents and counters for all interfaces that use the specified access list in a given direction. To display the contents of a specific access list entry, use the sequence number keyword and argument. The access group for an interface must be configured using the ipv6 access-group command for access list hardware counters to be enabled.

Use the show access-lists ipv6 summary command to display a summary of all current IPv6 access lists. To display a summary of a specific IPv6 access list, use the name argument.

Use the show access-list ipv6 usage command to display a summary of all interfaces and access lists programmed on the specified line card.

Task ID

Task ID

Operations

acl

read

Examples

In the following example, the contents of all IPv6 access lists are displayed:


RP/0/RP0/CPU0:ios# show access-lists ipv6
Fri Oct 20 05:29:01.125 UTC
ipv6 access-list V6-INGRESS-ACL
10 permit ipv6 any any
20 deny udp any any

show alarms

To view alarm information, use the show alarms command in XR EXEC mode or Administration EXEC mode.

show alarms [ brief ] [ system ] [ active ]

Syntax Description

brief

Displays alarms in brief.

system

Displays system scope alarms related data.

active

Displays active alarms.

Command Default

None

Command Modes

XR EXEC

Administration EXEC

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

This command displays the alarm information. The command displays only the administration alarms in admin EXEC mode and all the alarms in XR EXEC mode.

Examples

The following example shows the output of the show alarms brief system active command.

RP/0/RPO/CPUO:P1AL 05#show alarms brief system active
Thu Feb 9 11:33:03.137 UTC
-----------------------------------------------------------------------------------------------
Active Alarms
-----------------------------------------------------------------------------------------------
Location          Severity      Group           Set time                    Description
------------------------------------------------------------------------------------------------
0/PM1             Major         Environ         01/25/2023 05:21:37 UTC     Power Module Error (PM VIN VOLT 00R)

0/PM1 DISABLED)   Major         Environ         01/25/2023 05:21:37 UTC     Power Module Output Disabled (PM OUTPUT_DISABLED)

RP/0/RPO/CPUO:P1AL 05#RP/0/RPO/CPU:Feb 9 11:33:05.115 UTC: phyl mgmt [152]: %PKT INFRA-FM-2 -FAULT CRITICAL : AL
ARM CRITICAL : PHYI-MDIO-ACCESS-ERROR : DECLARE : 0: Phyl MDI0 access failure detected

show cdp

To display global CDP information (including timer and hold-time information, information about neighboring devices, interfaces on which CDP is enabled, traffic between devices), use the show cdp command in EXEC mode.

show cdp { traffic | neighbors [ type number | detail ] | interface [ type number ] | entry { * | device-name [ * ] }[ version ] [ protocol ] }

Syntax Description

type

(Optional) Interface type that is connected to the neighbors about which you want information.

number

(Optional) Number of the interface connected to the neighbors about which you want information.

detail

(Optional) Displays detailed information about a neighbor (or neighbors) including network address, enabled protocols, hold time, and software version.

*

Dispalys all CDP neighbors.

device-name *

Name of the neighbor about which you want information. You can enter an optional asterisk (*) at the end of a device-name as a wildcard. For example, entering show cdp entry dev* will match all device names that begin with dev.

version

(Optional) Limits the display to information about the software version running on the device.

protocol

(Optional) Limits the display to information about the protocols enabled on the device.

Command Default

No default behavior or values.

Command Modes

EXEC

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

Use the show cdp command to display global CDP information.


RP/0/RP0/CPU0:ios#show cdp
Tue Feb 14 16:59:38.255 UTC
Global CDP information:
        Sending CDP packets every 60 seconds
        Sending a holdtime value of 180 seconds
        Sending CDPv2 advertisements is enabled

Use the show cdp neighbors command to display detailed information about neighboring devices discovered using CDP.


RP/0/RP0/CPU0:R2#show cdp neighbors mgmtEth 0/RP0/CPU0/1 
Mon Apr 10 12:30:30.902 UTC
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater

Device ID       Local Intrfce    Holdtme Capability Platform  Port ID
R1              Mg0/RP0/CPU0/1   172     R          NCS1010   Mg0/RP0/CPU0/1  
RP/0/RP0/CPU0:R2#show cdp neighbors 
Mon Apr 10 12:30:39.251 UTC
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater

Device ID       Local Intrfce    Holdtme Capability Platform  Port ID
R1              Mg0/RP0/CPU0/1   164     R          NCS1010   Mg0/RP0/CPU0/1

RP/0/RP0/CPU0:R2#show cdp neighbors mgmtEth 0/RP0/CPU0/1 detail 
Mon Apr 10 12:31:23.622 UTC

-------------------------
Device ID: R1
SysName : R1
Entry address(es): 
  IPv4 address: 192.168.0.2
  IPv6 address: 2000:110::1
Platform: cisco NCS1010,  Capabilities: Router 
Interface: MgmtEth0/RP0/CPU0/1
Port ID (outgoing port): MgmtEth0/RP0/CPU0/1
Holdtime : 120 sec

Version :
7.10.1.19I

advertisement version: 2
Duplex: full

Use the show cdp entry entry-name command to display information about a specific neighboring device or all the neighboring devices discovered using CDP.


RP/0/RP0/CPU0:R2#show cdp entry R1
Mon Apr 10 12:22:22.564 UTC

-------------------------
Device ID: R1
SysName : R1
Entry address(es): 
  IPv4 address: 192.168.0.2
  IPv6 address: 2000:110::1
Platform: cisco NCS1010,  Capabilities: Router 
Interface: MgmtEth0/RP0/CPU0/1
Port ID (outgoing port): MgmtEth0/RP0/CPU0/1
Holdtime : 121 sec

Version :
7.10.1.19I

advertisement version: 2
Duplex: full

RP/0/RP0/CPU0:R2#show cdp entry *                 
Mon Apr 10 12:24:59.927 UTC

-------------------------
Device ID: R1
SysName : R1
Entry address(es): 
  IPv4 address: 192.168.0.2
  IPv6 address: 2000:110::1
Platform: cisco NCS1010,  Capabilities: Router 
Interface: MgmtEth0/RP0/CPU0/1
Port ID (outgoing port): MgmtEth0/RP0/CPU0/1
Holdtime : 143 sec

Version :
7.10.1.19I

advertisement version: 2
Duplex: full

Use the show cdp interface [interface-name] command to display information about the interfaces on which CDP is enabled.


RP/0/RP0/CPU0:R2#show cdp interface Mg0/RP0/CPU0/1
Mon Apr 10 12:24:27.253 UTC
MgmtEth0/RP0/CPU0/1 is Up
  Encapsulation ether
  Sending CDP packets every 60 seconds
  Holdtime is 180 seconds

Use the show cdp traffic command to display information about the traffic gathered between devices using CDP.


RP/0/RP0/CPU0:ios#show cdp traffic 
Mon Apr 10 12:32:09.247 UTC

CDP counters :
        Packets output: 11, Input: 5
        Hdr syntax: 0, Chksum error: 0, Encaps failed: 0
        No memory: 0, Invalid packet: 0, Truncated: 0
        CDP version 1 advertisements output: 0, Input: 0
        CDP version 2 advertisements output: 11, Input: 5
        Unrecognize Hdr version: 0, File open failed: 0

show configuration commit changes

To display the changes made to the running configuration by previous configuration commits, a configuration commit, or for a range of configuration commits, use the show configuration commit changes command in EXEC, administration EXEC, administration configuration, or global configuration mode.

show configuration commit changes { commit-id | since commit-id | last number-of-commits | original last-modified | all } [diff]

Syntax Description

since

Displays all changes committed to the running configuration since (and including) a specific configuration commit.

commit-id

Displays configuration changes for a specific configuration commit.

last number-of-commits

Displays the changes made to the running configuration during the last number of configuration commits specified for the number-of-commits argument.

original last-modified

Displays the original content of the actual commit operation before policy modifications by commit scripts.

all

Displays commit ID and configurations completed for last 100 commits.

diff

(Optional) Displays added lines, changed lines, and deleted lines.

Command Default

None

Command Modes

EXEC

Administration EXEC

Administration configuration

Global configuration

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Each time a configuration is committed with the commit command, the configuration commit operation is assigned a commit ID. The show configuration commit changes command displays the configuration changes made since the specified commit.

To display a list of the available commit IDs, enter the show configuration commit list command. You can also display the commit IDs by entering the show configuration commit changes command with the online help function (? ).

You cannot view commit IDs from a different release if the syntax or semantics of the configuration changed in the current release.


Note


Syntax of a configuration refers to its structure and format, while the semantics of a configuration refers to its backend interpretation.


Examples

The following example shows sample output from the show configuration commit changes command with the commit-id argument. In this example, the output displays the changes made in the configuration commit assigned commit ID 1000000006.


RP/0/RP0/CPU0:ios#show configuration commit changes 1000000006
Building configuration...

controller Ots0/0/0/0
 raman-osri off
 raman-force-apr off
 raman-tx-power 1 value 22300
 raman-tx-power 2 value 26800
 raman-tx-power 3 value 6400
 raman-tx-power 4 value 12900
 raman-tx-power 5 value 19000
 raman-safety-control-mode auto
!
end
  

The following example shows sample output from the show configuration commit changes command with the since commit-id keyword and argument. In this example, the output displays the configuration changes made since the configuration commit assigned commit ID 1000000006 was committed.

RP/0/RP0/CPU0:ios#show configuration commit changes since 1000000006
Tue Feb 28 11:41:04.643 UTC
Building configuration...
controller Ots0/0/0/0
 otdr rx auto reflectance-threshold -45
 otdr rx auto splice-loss-threshold 200
 otdr rx auto excess-reflection-threshold -20
 otdr rx expert capture-end 8000000
 otdr rx expert pulse-width 20000
 otdr rx expert capture-start 5000000
 otdr rx expert scan-duration 160
 otdr rx back-scattering -8200
 otdr rx refractive-index 1468000
 otdr tx auto reflectance-threshold -48
 otdr tx auto splice-loss-threshold 250
 otdr tx auto excess-reflection-threshold -22
 otdr tx expert capture-end 9000000
 otdr tx expert pulse-width 5000
 otdr tx expert capture-start 6000000
 otdr tx back-scattering -8300
 otdr tx refractive-index 1468200
 otdr scan-mode expert
 raman-osri off
 raman-force-apr off
 raman-tx-power 1 value 22300
 raman-tx-power 2 value 26800
 raman-tx-power 3 value 6400
 raman-tx-power 4 value 12900
 raman-tx-power 5 value 19000
 raman-safety-control-mode auto
!
end



The following example shows sample output from the show configuration commit changes command with the diff keyword. In the display, the following symbols signify changes:

+ indicates an added line.

– indicates a deleted line.

# indicates a modified line.

RP/0/RP0/CPU0:R1#show configuration commit changes since 1000000006 diffBuilding configuration...
+  controller Ots0/0/0/0
+   otdr rx auto reflectance-threshold -45
+   otdr rx auto splice-loss-threshold 200
+   otdr rx auto excess-reflection-threshold -20
+   otdr rx expert capture-end 8000000
+   otdr rx expert pulse-width 20000
+   otdr rx expert capture-start 5000000
+   otdr rx expert scan-duration 160
+   otdr rx back-scattering -8200
+   otdr rx refractive-index 1468000
+   otdr tx auto reflectance-threshold -48
+   otdr tx auto splice-loss-threshold 250
+   otdr tx auto excess-reflection-threshold -22
+   otdr tx expert capture-end 9000000
+   otdr tx expert pulse-width 5000
+   otdr tx expert capture-start 6000000
+   otdr tx back-scattering -8300
+   otdr tx refractive-index 1468200
+   otdr scan-mode expert
+   raman-osri off
+   raman-force-apr off
+   raman-tx-power 1 value 22300
+   raman-tx-power 2 value 26800
+   raman-tx-power 3 value 6400
+   raman-tx-power 4 value 12900
+   raman-tx-power 5 value 19000
+   raman-safety-control-mode auto
+  !
end

The following example shows sample output from the show configuration commit changes command with the all keyword. In this example, the output displays the list of configurations that are committed in last 100 commits along with their commit-ID.

RP/0/RP0/CPU0:ios#show configuration commit changes all
Tue Feb 28 11:38:42.876 UTC

 Commit ID :  1000000001
------------------------------------------------------
Building configuration...
username cisco
 group root-lr
 group cisco-support
 secret 10 $6$PAYio/1d9RuG5o/.$daupPZwNJCuPsJqAGa8IlhAq8U1O2Qa8UdtVszjh4MaRWixFfGvNfFq/FPB36DH07v77oCOssLTZ4LUxN88QT.
!
end


 Commit ID :  1000000002
------------------------------------------------------
Building configuration...
call-home
 service active
 contact smart-licensing
 profile CiscoTAC-1
  active
  destination transport-method email disable
  destination transport-method http
 !
!
end


 Commit ID :  1000000003
------------------------------------------------------
Building configuration...

hostname R1
logging console disable
line console
 exec-timeout 0 0
 absolute-timeout 0
 session-timeout 0
!
line default
 exec-timeout 0 0
 absolute-timeout 0
 session-timeout 0
!
end


 Commit ID :  1000000004
------------------------------------------------------
Building configuration...

line console
 exec-timeout 0 0
 absolute-timeout 0
 session-timeout 0
!
line default
 exec-timeout 0 0
 absolute-timeout 0
 session-timeout 0
!
end


 Commit ID :  1000000005
------------------------------------------------------
Building configuration...

controller Ots0/0/0/0
 egress-ampli-br enable
 egress-ampli-force-apr off
 egress-ampli-osri off
 egress-ampli-tilt 11
 egress-ampli-br-high-threshold -170
 ingress-ampli-force-apr off
 egress-ampli-gain 190
 ingress-ampli-osri off
 ingress-ampli-tilt -11
 ingress-ampli-gain 200
 ingress-ampli-gain-range normal
 egress-ampli-safety-control-mode auto
 ingress-ampli-safety-control-mode auto
!
end


 Commit ID :  1000000006
------------------------------------------------------
Building configuration...

controller Ots0/0/0/0
 raman-osri off
 raman-force-apr off
 raman-tx-power 1 value 22300
 raman-tx-power 2 value 26800
 raman-tx-power 3 value 6400
 raman-tx-power 4 value 12900
 raman-tx-power 5 value 19000
 raman-safety-control-mode auto
!
end


 Commit ID :  1000000007
------------------------------------------------------
Building configuration...

controller Ots0/0/0/0
 otdr rx auto reflectance-threshold -45
 otdr rx auto splice-loss-threshold 200
 otdr rx auto excess-reflection-threshold -20
 otdr rx expert capture-end 8000000
 otdr rx expert pulse-width 20000
 otdr rx expert capture-start 5000000
 otdr rx expert scan-duration 160
 otdr rx back-scattering -8200
 otdr rx refractive-index 1468000
 otdr tx auto reflectance-threshold -48
 otdr tx auto splice-loss-threshold 250
 otdr tx auto excess-reflection-threshold -22
 otdr tx expert capture-end 9000000
 otdr tx expert pulse-width 5000
 otdr tx expert capture-start 6000000
 otdr tx back-scattering -8300
 otdr tx refractive-index 1468200
 otdr scan-mode expert
!
end




show controllers

To display status and configuration information about the interfaces on a specific node, use the show controllers command in XR EXEC mode.

Show controllers [ description ] [ Controller-type R/S/I/P ] [ spectrum-info ] [ otdr-info direction ] [ tone-info ] [ channel-slice-attenuation-info ]

Syntax Description

description

Displays the controller status.

Controller-type R/S/I/P

Rack/Slot/Instance/Port of the controller.

spectrum-info

Displays the Optical Channel Monitoring (OCM) raw data at slice level, such as Tx-power and Rx-power.

otdr-info

Displays the OTDR scan status and location of the SOR file, and the OTDR events.

direction

Scan direction (RX or TX)

channel-slice-attenuation-info

Displays the attenuation data for each channel slice

tone-info

Displays the Tone Generation parameters that are set for connection verification and the status of the connection verification operation.

Command Default

None

Command Modes

XR EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

To view the OTS controller status on the ILA cards, use the sh controller description command.

RP/0/RP0/CPU0:ios#sh controller description
Fri Mar 25 09:24:53.386 UTC
Interface Status Description
--------------------------------------------------------------------------------
Osc0/0/0/0 up
Osc0/0/0/2 up
Ots0/0/0/0 up
Ots0/0/0/1 up
Ots0/0/0/2 up
Ots0/0/0/3 up
RP/0/RP0/CPU0:ios#

To view the parameters of the LINE 0 OTS controller, use the following command:

RP/0/RP0/CPU0:ios#sh controllers ots 0/0/0/0
Wed Mar 23 06:00:37.097 UTC
Controller State: Up
Transport Admin State: In Service
LED State: Red
Alarm Status:
-------------
Detected Alarms:
RX-LOS-P
EGRESS-AUTO-LASER-SHUT
HIGH-RX-BR-PWR
Alarm Statistics:
-----------------
LOW-TX-PWR = 0
RX-LOS-P = 1
RX-LOC = 1
TX-POWER-FAIL-LOW = 1
INGRESS-AUTO-LASER-SHUT = 0
INGRESS-AUTO-POW-RED = 0
INGRESS-AMPLI-GAIN-LOW = 0
INGRESS-AMPLI-GAIN-HIGH = 0
EGRESS-AUTO-LASER-SHUT = 1
EGRESS-AUTO-POW-RED = 0
EGRESS-AMPLI-GAIN-LOW = 0
EGRESS-AMPLI-GAIN-HIGH = 0
HIGH-TX-BR-PWR = 0
HIGH-RX-BR-PWR = 1
SPAN-TOO-SHORT-TX = 0
SPAN-TOO-SHORT-RX = 0
Parameter Statistics:
---------------------
Total RX Power(C+L) = -50.00 dBm
Total TX Power(C+L) = -50.00 dBm
Total RX Power = -50.00 dBm
Total TX Power = -50.00 dBm
RX Signal Power = -50.00 dBm
TX Signal Power = -50.00 dBm
TX Voa Attenuation = 0.0 dB
Ingress Ampli Gain = -1.1 dB
Ingress Ampli Tilt = 0.0 dB
Ingress Ampli Gain Range = Normal
Ingress Ampli Safety Control mode = auto
Ingress Ampli Osri = OFF
Ingress Ampli Force Apr = OFF
Egress Ampli Gain = -0.7 dB
Egress Ampli Tilt = 0.0 dB
Egress Ampli Safety Control mode = auto
Egress Ampli Osri = OFF
Egress Ampli Force Apr = OFF
Configured Parameters:
-------------
TX Voa Attenuation = 0.0 dB
Ingress Ampli Gain = 10.9 dB
Ingress Ampli Tilt = 0.0 dB
Ingress Ampli Gain Range = Normal
Ingress Ampli Safety Control mode = auto
Ingress Ampli Osri = OFF
Ingress Ampli Force Apr = OFF
Egress Ampli Gain = 15.3 dB
Egress Ampli Tilt = 0.0 dB
Egress Ampli Safety Control mode = auto
Egress Ampli Osri = OFF
Egress Ampli Force Apr = OFF
RP/0/RP0/CPU0:ios#

Examples

To view the raw OCM data (slice level channel power) use the following commands:

RP/0/RP0/CPU0:ios#sh controllers ots 0/0/0/0 spectrum-info 
Fri Feb 4 13:12:49.841UTC​
Spectrum Slices spacing        :            3.125 GHz​
Spectrum Slices Range          :            1 - 1548​
Slice start wavelength         :            1566.82 nm​
Slice start frequency          :            191337.50 GHz​
Spectrum power information :​
Rx power :​
----------------------------------------------------------------------------------​
spectrum-slice num                        Rx-power values (dBm)​
----------------------------------------------------------------------------------​
   1 - 12               -88.8  -88.8  -88.8  -88.8      -88.8  -88.8  -88.8  -88.8      -88.8  -88.8  -88.8  -88.8​
  13 - 24               -88.8  -88.8  -88.8  -88.8      -88.8  -88.8  -88.8  -88.8      -88.8  -88.8  -88.8  -88.8​
…....​
…....​
…....​
1537 - 1548             -88.8  -88.8  -88.8  -88.8      -88.8  -88.8  -88.8  -88.8      -88.8  -88.8  -88.8  -88.8​
----------------------------------------------------------------------------------​
Tx power :​
----------------------------------------------------------------------------------​
spectrum-slice num                        Tx-power values (dBm)​
----------------------------------------------------------------------------------​
1 - 12                -9.5   -7.3   -6.0   -5.2       -4.9   -4.8   -4.6   -4.4       -4.4   -4.4   -4.4   -4.4​
13 - 24                -4.4   -4.5   -4.6   -4.8       -5.1   -5.5   -6.4   -7.7       -9.6  -12.0  -13.2  -11.4​
25 - 36                -9.2   -7.7   -6.7   -6.2       -6.0   -5.9   -5.7   -5.6       -5.6   -5.5   -5.4   -5.4​
37 - 48                -5.3   -5.3   -5.4   -5.5       -5.8   -6.1   -6.6   -7.3       -8.6  -10.4  -12.2  -11.8​
…...​
…...​
…...​
1525 - 1536              -2.4   -2.4   -2.4   -2.4       -2.4   -2.3   -2.3   -3.0       -4.2   -6.5  -10.3  -14.9​
1537 - 1548             -19.3  -22.6  -24.3  -25.3      -26.1  -26.6  -27.1  -27.6      -27.9  -28.2  -28.4  -28.6​
​

To view the OTDR scan status and events use the following commands:

RP/0/RP0/CPU0:ios#show controllers ots 0/0/0/0 otdr-info rx 
Wed Feb  9 05:55:19.791 UTC 
        Scan Direction: RX 
        Scan Status: Data Ready  
        SOR file: /harddisk:/otdr/P1D_DT_01_NCS1010_OTDR_Ots0_0_0_0_RX_20220209-055045.sor 
        Total Events detected: 11 
        Scan Timestamp: Wed Feb  9 05:50:45 2022 UTC 
        Event Type Legend:  NR:Non-Reflective  R:Reflective  FE:Fiber-End  ER:Excess-Reflection
Event# | Detected Event(s) | Location(km) | Accuracy(m) | Magnitude(dB) | Attenuation/km(dB)
1      | R                 | 50.4709      | 52.47       | -39.87        | 0.18  
2      | NR                | 50.4709      | 52.47       | 1.17          | 0.18   
3      | R                 | 100.9261     | 102.92      | -37.73        | 0.21    
4      | NR                | 100.9261     | 102.92      | 1.01          | 0.21    
5      | R                 | 105.9500     | 107.94      | -38.52        | 0.24               
6      | NR                | 105.9500     | 107.94      | 0.85          | 0.24             
7      | R                 | 112.7458     | 114.74      | -40.56        | 0.00             
8      | NR                | 112.7458     | 114.74      | 1.48          | 0.00             
9      | NR                | 117.9873     | 119.98      | 0.66          | -0.02             
10     | R FE              | 120.1206     | 122.12      | -35.55        | 0.00            
          
        11     | NR FE             | 120.1206     | 122.12      | 21.65         | 0.00            

The following sample displays the Optical Return Loss as part of the OTDR status:

RP/0/RP0/CPU0:NCS1010#show controllers Ots 0/0/0/2 otdr-info rx
Mon Oct  2 11:55:48.552 UTC 
        Scan Direction: RX 
        Scan Status: Data Ready 
        Optical Return Loss: 39.0 dB 
        SOR file: /harddisk:/otdr/NCS1010_NCS1010_OTDR_Ots0_0_0_2_RX_20231001-110754.sor 
        Total Events detected: 8 
        Scan Timestamp: Sun Oct  1 11:07:54 2023 UTC 
        Event Type Legend:  NR:Non-Reflective  R:Reflective  FE:Fiber-End  ER:Excess-Reflection EA:Excess-Attenuation
 
 Event# |  Detected Event(s) |  Location(m) |  Accuracy(m) |  Magnitude(dB) |  Attenuation/km(dB)
 1      |  NR EA             |  4.4100      |  2.00        |  0.69          |  0.00            
 2      |  NR                |  664.3200    |  2.66        |  0.21          |  0.00             
 3      |  R ER              |  18222.3900  |  20.22       |  -33.78        |  0.19             
 4      |  NR                |  18222.3900  |  20.22       |  0.35          |  0.19  
 5      |  R ER              |  68674.4800  |  70.67       |  -32.25        |  0.20             
 6      |  NR                |  68674.4800  |  70.67       |  0.36          |  0.20  
 7      |  R FE ER           |  118765.2600 |  120.76      |  -28.55        |  0.23  
 8      |  NR FE             |  118765.2600 |  120.76      |  25.86         |  0.23  
To view the parameter values set for Tone Generation and the status of connection verification on port 4 OTS controller, use the following command:
RP/0/RP0/CPU0:ios#show controllers ots 0/0/0/4 tone-info  
Fri Sep 15 14:53:22.579 UTC
Tone Info:
Tone Frequency : 191.3750000 THz
Tone Rate : 2 bits/second
Tone Pattern(Hex value) : abcd1234
Tone Pattern Expected(Hex value) : abcd1234
Tone Pattern Received(Hex value) : 00000000
Tone Detected OOB :  Enabled
 Detection State: Inprogress
To view the parameter values set for Tone Generation and the status of connection verification on the OMS controller, use the following command:
RP/0/RP0/CPU0:#show controllers oms 0/2/0/0 tone-info
Tue May 10 11:41:18.847 UTC
Tone Info:
Tone Rate : 25 bits/second
Tone Pattern Expected(Hex value) : abcd1234
Tone Pattern Received(Hex value) : abcd1234
Tone Detected OOB : Enabled
Detection State: Success

show controllers raman-info

To view the individual Raman pump information and other parameters, use the show controllers ots r/s/i/p raman-info command.

show controllers ots R/S/I/P raman-info

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

Command Modes

User EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following sample shows the output of the show controllers ots r/s/i/p raman-info command.

RP/0/RP0/CPU0:ios#show controllers ots 0/0/0/0 raman-info 
Fri Apr  1 06:40:33.849 UTC

         Alarm Status:
         -------------
         Detected Alarms: None


         Alarm Statistics:
         -----------------
         RAMAN-AUTO-POW-RED = 0          
         RAMAN-1-LOW-POW = 0          
         RAMAN-2-LOW-POW = 0          
         RAMAN-3-LOW-POW = 0          
         RAMAN-4-LOW-POW = 0          
         RAMAN-5-LOW-POW = 0          
         RAMAN-1-HIGH-POW = 1          
         RAMAN-2-HIGH-POW = 0          
         RAMAN-3-HIGH-POW = 0          
         RAMAN-4-HIGH-POW = 0          
         RAMAN-5-HIGH-POW = 0          

         Parameter Statistics:
         ---------------------
         Raman Safety Control mode = auto 
         Raman Osri = OFF 
         Raman Force Apr = OFF 
         Composite Raman Power = 886.60 mW

         RAMAN Pump Info:
         ---------------------
         Instance        Wavelength(nm)  Power(mW)
          1               1424.00                 257.60
          2               1438.00                 255.10
          3               1457.00                 71.60
          4               1470.00                 127.50
          5               1495.00                 170.10



         Configured Parameters:
         -------------
         Raman Safety Control mode = auto 
         Raman Osri = OFF 
         Raman Force Apr = OFF 

         RAMAN Pump Info:
         ---------------------
         Instance        Power(mW)
          1               45.00
          2               40.00
          3               40.00
          4               40.00
          5               35.00

show environment

To display environmental monitor parameters for the system, use the show environment command.

show environment [ alarm-contact | all | altitude | current | fan | humidity | power | voltages [ location | location ] | temperature [ location | location ] ]

Syntax Description

alarm-contact

(Optional) Displays information about the alarm ports.

all

(Optional) Displays information for all the environmental monitor parameters.

altitude

(Optional) Displays information about the altitude.

current

(Optional) Displays current sensor information.

fan

(Optional) Displays information about the fans.

humidity

(Optional) Displays information about the humidity.

power

(Optional) Displays power supply voltage and current information.

temperature

(Optional) Displays system temperature information.

voltages

(Optional) Displays system voltage information.

location | location

(Optional) Enter the location for which the environmental information needs to be displayed.

Command Default

All environmental monitor parameters are displayed.

Command Modes

Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

The show environment command displays information about the hardware that is installed in the system, including fans, power supply voltage, current information, and temperatures.

Examples

The following example shows sample output from the show environment command with the fan keyword.

sysadmin-vm:0_RP0# show environment fan
Thu May 26 04:15:37.765 UTC
===========================================================================
                                              Fan speed (rpm)
Location      FRU Type                        FAN_0    FAN_1   FAN_2   
---------------------------------------------------------------------------

0/PM0        NCS1010-AC-PSU                     5368   
0/PM1        NCS1010-AC-PSU                     5336   
0/FT0        NCS1010-FAN                       10020   10020   10020   
0/FT1        NCS1010-FAN                       10020   10020    9960   

==============================================================================

The following example shows sample output from the show environment command with the temperature keyword.

sysadmin-vm:0_RP0# show environment temperature location 0/RP0
Thu May 26 04:16:39.832 UTC
=============================================================================================================
Location  TEMPERATURE                          Value     Crit    Major    Minor    Minor    Major    Crit
          Sensor                             (deg C)     (Lo)     (Lo)     (Lo)     (Hi)     (Hi)    (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_TEMP_PCB                            30      -10       -5        0       70       75       80
          RP_TEMP_HOT_SPOT                       33      -10       -5        0       70       75       80
          RP_TEMP_LTM4638                        49      -10       -5        0       80       85       90
          RP_TEMP_LTM4644_0                      36      -10       -5        0       80       85       90
          RP_TEMP_LTM4644_1                      39      -10       -5        0       80       85       90
          RP_JMAC_1V0_VCCP_TMON                  33      -10       -5        0       80       85       90
          RP_JMAC_1V0_VNN_TMON                   33      -10       -5        0       80       85       90
          RP_JMAC_1V0_VCC_RAM_TMON               32      -10       -5        0       80       85       90
          RP_JMAC_1V2_DDR_VDDQ_TMON              33      -10       -5        0       80       85       90
================================================================================================================

The following example shows sample output from the show environment command with the power keyword.

sysadmin-vm:0_RP0# show environment power
Thu May 26 04:17:55.592 UTC
================================================================================
CHASSIS LEVEL POWER INFO: 0
================================================================================
   Total output power capacity (Group 0 + Group 1) :    1050W +     1050W
   Total output power required                     :     700W
   Total power input                               :     228W
   Total power output                              :     140W

Power Group 0:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM0       NCS1010-AC-PSU  228.5     0.5     12.1      5.6      OK

Total of Group 0:              114W/0.5A         67W/5.6A

Power Group 1:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM1       NCS1010-AC-PSU  228.5     0.5     12.1      6.1      OK
          
Total of Group 1:              114W/0.5A         73W/6.1A
          
================================================================================
   Location     Card Type               Power       Power        Status
                                        Allocated   Used
                                        Watts       Watts
================================================================================
   0/RP0/CPU0   NCS1010-CNTLR-K9        90          14           ON
   0/FT0        NCS1010-FAN             110         17           ON
   0/FT1        NCS1010-FAN             110         15           ON
   0/0/NXR0     NCS1K-OLT-C             350         61           ON
   0/Rack       NCS1010-SA              40          19           ON


=================================================================================

The following example shows sample output from the show environment command with the voltages keyword.

sysadmin-vm:0_RP0# show environment voltages location 0/RP0
Thu May 26 04:19:16.636 UTC
=============================================================================================================
Location  VOLTAGE                             Value      Crit    Minor    Minor     Crit
          Sensor                              (mV)       (Lo)    (Lo)     (Hi)      (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_ADM1266_12V0                     12094    10800    11280    12720    13200
          RP_ADM1266_1V8_CPU                   1806     1670     1750     1850     1930
          RP_ADM1266_1V24_VCCREF               1238     1150     1200     1280     1330
          RP_ADM1266_1V05_CPU                  1047      980     1020     1080     1120
          RP_ADM1266_1V2_DDR_VDDQ              1204     1120     1160     1240     1280
          RP_ADM1266_1V0_VCC_RAM                988      650      700     1250     1300
          RP_ADM1266_1V0_VNN                    869      550      600     1250     1300
          RP_ADM1266_1V0_VCCP                  1018      450      500     1250     1300
          RP_ADM1266_0V6_DDR_VTT                599      560      580      620      640
          RP_ADM1266_3V3_STAND_BY              3301     3070     3200     3400     3530
          RP_ADM1266_5V0                       5004     4650     4850     5150     5350
          RP_ADM1266_3V3                       3325     3070     3200     3400     3530
          RP_ADM1266_2V5_PLL                   2489     2330     2430     2580     2680
          RP_ADM1266_2V5_FPGA                  2502     2330     2430     2580     2680
          RP_ADM1266_1V2_FPGA                  1202     1120     1160     1240     1280
          RP_ADM1266_3V3_CPU                   3332     3070     3200     3400     3530
          RP_ADM1266_2V5_CPU                   2498     2330     2430     2580     2680

===============================================================================================================
The following example shows a sample output of the show environment current command.
RP/0/RP0/CPU0:P2C_DT_02#show environment current 
Tue Jul  5 08:36:22.132 UTC
=====================================================
Location  CURRENT                              Value 
          Sensor                               (mA)  
-----------------------------------------------------
0/RP0/CPU0 
          RP_CURRMON_LTM4638                    395
          RP_CURRMON_LTM4644_0                  179
          RP_CURRMON_LTM4644_1                  307
          RP_JMAC_1V0_VCCP_IMON                 187
          RP_JMAC_1V0_VNN_IMON                   62
          RP_JMAC_1V0_VCC_RAM_IMON                0
          RP_JMAC_1V2_DDR_VDDQ_IMON             187
0/Rack     
          SA_ADM1275_12V_MOD0_IMON             4154
          SA_ADM1275_12V_MOD1_IMON               43
          SA_ADM1275_12V_MOD2_IMON               18
          SA_ADM1275_12V_FAN0_IMON             1356
          SA_ADM1275_12V_FAN1_IMON             1517
          SA_INA230_5V0_IMON                    129
          SA_INA230_3V3_IMON                   2998
          SA_INA230_1V0_XGE_CORE_IMON          2464
          SA_INA230_1V0_FPGA_CORE_IMON          787
          SA_ADM1275_12V_SA_IMON               1668
          SA_ADM1275_12V_CPU_IMON              1147
The following example shows a sample output from the show environment altitude command.
RP/0/RP0/CPU0:P2C_DT_02#show environment altitude 
Tue Jul  5 08:36:51.710 UTC
================================================================================
Location     Altitude Value (Meters)    Source         
--------------------------------------------------------------------------------
0            760                    sensor

The following example shows sample output from the show environment command.

sysadmin-vm:0_RP0# show environment
Thu May 26 04:20:09.507 UTC
=============================================================================================================
Location  TEMPERATURE                          Value     Crit    Major    Minor    Minor    Major    Crit
          Sensor                             (deg C)     (Lo)     (Lo)     (Lo)     (Hi)     (Hi)    (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_TEMP_PCB                            30      -10       -5        0       70       75       80
          RP_TEMP_HOT_SPOT                       33      -10       -5        0       70       75       80
          RP_TEMP_LTM4638                        49      -10       -5        0       80       85       90
          RP_TEMP_LTM4644_0                      36      -10       -5        0       80       85       90
          RP_TEMP_LTM4644_1                      39      -10       -5        0       80       85       90
          RP_JMAC_1V0_VCCP_TMON                  33      -10       -5        0       80       85       90
          RP_JMAC_1V0_VNN_TMON                   33      -10       -5        0       80       85       90
          RP_JMAC_1V0_VCC_RAM_TMON               32      -10       -5        0       80       85       90
          RP_JMAC_1V2_DDR_VDDQ_TMON              34      -10       -5        0       80       85       90
0/PM0      
          Ambient Temp                           30      -10       -5        0       55       60       65
          Secondary HotSpot Temp                 49      -10       -5        0       65       70       75
          Primary HotSpot Temp                   40      -10       -5        0       85       90       95
0/PM1      
          Ambient Temp                           29      -10       -5        0       55       60       65
          Secondary HotSpot Temp                 48      -10       -5        0       65       70       75
          Primary HotSpot Temp                   40      -10       -5        0       85       90       95
0/0/NXR0   
          OLTC_LT_P0_iEDFA0                      24       18       19       20       30       31       32
          OLTC_LT_P0_iEDFA1                      25       18       19       20       30       31       32
          OLTC_LT_P0_iEDFA2                      24       18       19       20       30       31       32
          OLTC_LT_P2_iEDFA0                      25       18       19       20       30       31       32
          OLTC_LT_P3_iEDFA0                      25       18       19       20       30       31       32
          OLTC_LT_P0_eEDFA0                      24       18       19       20       30       31       32
          OLTC_CT_1                              32      -10       -7       -5       75       77       80
          OLTC_LT_P0_eEDFA1                      24       18       19       20       30       31       32
          OLTC_CT_2                              27      -10       -7       -5       70       73       75
          OLTC_CT_3                              30      -10       -7       -5       70       73       75
          OLTC_CT_4                              30      -10       -7       -5       70       73       75
          OLTC_FT_P0_iEDFA0                      60       55       57       58       62       64       65
          OLTC_FT_P2_iEDFA0                      60       55       57       58       62       64       65
          OLTC_FT_P3_iEDFA0                      60       55       57       58       62       64       65
          OLTC_FT_P0_eEDFA0                      60       55       57       58       62       64       65
0/Rack     
          SA_TEMP_AIR_INLET0                     27      -10       -5        0       45       55       60
          SA_TEMP_AIR_INLET1                     28      -10       -5        0       45       55       60
          SA_TEMP_AIR_EXAUST0                    30      -10       -5        0       75       85       90
          SA_TEMP_AIR_EXAUST1                    28      -10       -5        0       75       85       90
          SA_TEMP_PCB_HOT_SPOT0                  31      -10       -5        0       80       85       90
          SA_TEMP_PCB_HOT_SPOT1                  34      -10       -5        0       80       85       90
          SA_TEMP_PCB_HOT_SPOT2                  31      -10       -5        0       80       85       90
          SA_TEMP_PCB_HOT_SPOT3                  32      -10       -5        0       80       85       90
=============================================================================================================
Location  VOLTAGE                             Value      Crit    Minor    Minor     Crit
          Sensor                              (mV)       (Lo)    (Lo)     (Hi)      (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_ADM1266_12V0                     12094    10800    11280    12720    13200
          RP_ADM1266_1V8_CPU                   1806     1670     1750     1850     1930
          RP_ADM1266_1V24_VCCREF               1238     1150     1200     1280     1330
          RP_ADM1266_1V05_CPU                  1052      980     1020     1080     1120
          RP_ADM1266_1V2_DDR_VDDQ              1204     1120     1160     1240     1280
          RP_ADM1266_1V0_VCC_RAM                988      650      700     1250     1300
          RP_ADM1266_1V0_VNN                    871      550      600     1250     1300
          RP_ADM1266_1V0_VCCP                  1018      450      500     1250     1300
          RP_ADM1266_0V6_DDR_VTT                599      560      580      620      640
          RP_ADM1266_3V3_STAND_BY              3301     3070     3200     3400     3530
          RP_ADM1266_5V0                       5004     4650     4850     5150     5350
          RP_ADM1266_3V3                       3325     3070     3200     3400     3530
          RP_ADM1266_2V5_PLL                   2489     2330     2430     2580     2680
          RP_ADM1266_2V5_FPGA                  2502     2330     2430     2580     2680
          RP_ADM1266_1V2_FPGA                  1197     1120     1160     1240     1280
          RP_ADM1266_3V3_CPU                   3332     3070     3200     3400     3530
          RP_ADM1266_2V5_CPU                   2498     2330     2430     2580     2680
0/Rack     
          SA_ADM1266_12V_BUS_EITU             12065    10800    11280    12720    13200
          SA_ADM1266_5V0                       5033     4650     4800     5200     5350
          SA_ADM1266_1V8_ZARLINK_DPLL          1808     1670     1730     1870     1930
          SA_ADM1266_1V0_PHY                   1009      930      960     1040     1070
          SA_ADM1266_1V0_ALDRIN_CORE            981      910      930     1070     1090
          SA_ADM1266_1V0_ALDRIN_SERDES         1006      930      960     1040     1070
          SA_ADM1266_1V0_FPGA                  1010      930      960     1040     1070
          SA_ADM1266_1V2_FPGA                  1211     1120     1150     1250     1280
          SA_ADM1266_1V8                       1804     1670     1730     1870     1930
          SA_ADM1266_2V5                       2498     2330     2400     2600     2680
          SA_ADM1266_3V3                       3308     3070     3170     3430     3530
          SA_ADM1275_12V_SA_BP                12073    10800    11280    12720    13200
          SA_ADM1275_12V_CPU_BP               12058    10800    11280    12720    13200
          SA_ADM1275_12V_MOD0_BP              12063    10800    11280    12720    13200
          SA_ADM1275_12V_MOD1_BP              12037    10800    11280    12720    13200
          SA_ADM1275_12V_MOD2_BP              12053    10800    11280    12720    13200
          SA_ADM1275_12V_FAN0_BP              12037    10800    11280    12720    13200
          SA_ADM1275_12V_FAN1_BP              12063    10800    11280    12720    13200
=============================================================================================================
Location  CURRENT                              Value    
          Sensor                               (mA)    
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_CURRMON_LTM4638                    395
          RP_CURRMON_LTM4644_0                  179
          RP_CURRMON_LTM4644_1                  311
          RP_JMAC_1V0_VCCP_IMON                  62
          RP_JMAC_1V0_VNN_IMON                   93
          RP_JMAC_1V0_VCC_RAM_IMON               62
          RP_JMAC_1V2_DDR_VDDQ_IMON             187
0/Rack     
          SA_ADM1275_12V_MOD0_IMON             5495
          SA_ADM1275_12V_MOD1_IMON                6
          SA_ADM1275_12V_MOD2_IMON                6
          SA_ADM1275_12V_FAN0_IMON             1146
          SA_ADM1275_12V_FAN1_IMON             1381
          SA_INA230_5V0_IMON                    323
          SA_INA230_3V3_IMON                   2584
          SA_INA230_1V0_XGE_CORE_IMON          2459
          SA_INA230_1V0_FPGA_CORE_IMON          784
          SA_ADM1275_12V_SA_IMON               1603
          SA_ADM1275_12V_CPU_IMON              1222
===========================================================================
                                              Fan speed (rpm)
Location      FRU Type                        FAN_0    FAN_1   FAN_2   
---------------------------------------------------------------------------
          
0/PM0        NCS1010-AC-PSU                     5456   
0/PM1        NCS1010-AC-PSU                     5336   
0/FT0        NCS1010-FAN                       10020   10020   10020   
0/FT1        NCS1010-FAN                        9960   10020    9960   
================================================================================
Location     Altitude Value (Meters)    Source         
--------------------------------------------------------------------------------
0            772                    sensor
          
================================================================================
CHASSIS LEVEL POWER INFO: 0
================================================================================
   Total output power capacity (Group 0 + Group 1) :    1050W +     1050W
   Total output power required                     :     700W
   Total power input                               :     206W
   Total power output                              :     138W
          
Power Group 0:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM0       NCS1010-AC-PSU  229.0     0.4     12.1      5.5      OK
          
Total of Group 0:               91W/0.4A         66W/5.5A
          
Power Group 1:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM1       NCS1010-AC-PSU  229.0     0.5     12.1      6.0      OK
          
Total of Group 1:              114W/0.5A         72W/6.0A
          
================================================================================
   Location     Card Type               Power       Power        Status
                                        Allocated   Used
                                        Watts       Watts
================================================================================
   0/RP0/CPU0   NCS1010-CNTLR-K9        90          14           ON
   0/FT0        NCS1010-FAN             110         16           ON
   0/FT1        NCS1010-FAN             110         16           ON
   0/0/NXR0     NCS1K-OLT-C             350         71           ON
   0/Rack       NCS1010-SA              40          19           ON
          
=========================================================================================================
==========================================================================================================

show fpd package

To determine the FPDs that are supported with the current software release and the minimum hardware requirements for each FPD, use the show fpd package command in Cisco IOS XR mode.

show fpd package [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about FPD upgrade.

Command Default

Firmware information of all the hardware components is displayed.

Command Modes

Cisco IOS XR EXEC

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example shows sample output from the show fpd package command.

RP/0/RP0/CPU0:ios#show fpd package
Wed Jun 29 08:50:21.057 UTC
=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                               Req     SW      Min Req   Min Req
Card Type            FPD Description           Reload  Ver     SW Ver  Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
NCS1010-AC-PSU       AP-PrimMCU                 NO      1.03      1.03      0.0  
                     AP-SecMCU                  NO      2.01      2.01      0.0  
--------------------------------------------------------------------------------
NCS1010-CNTLR-K9     ADMConfig                  NO      2.30      2.30      0.0  
                     ADMConfig                  NO      2.30      2.30      0.0  
                     ADMConfig                  NO      3.40      3.30      1.0  
                     BIOS                       YES     4.10      4.10      0.0  
                     BIOS                       YES     4.10      4.10      0.0  
                     BIOS-Golden                YES     4.10      4.10      0.0  
                     BIOS-Golden                YES     4.10      4.10      0.0  
                     CpuFpga                    YES     1.02      1.02      0.0  
                     CpuFpga                    YES     1.02      1.02      0.0  
                     CpuFpgaGolden              YES     1.01      1.01      0.0  
                     CpuFpgaGolden              YES     1.01      1.01      0.0  
                     SsdIntelS4510              YES    11.32     11.32      0.0  
                     SsdIntelS4510              YES    11.32     11.32      0.0  
                     SsdMicron5300              YES     0.01      0.01      0.0  
                     SsdMicron5300              YES     0.01      0.01      0.0  
                     SsdSmartModular            YES    13.06     13.06      0.0  
                     SsdSmartModular            YES    13.06     13.06      0.0  
                     TamFw                      YES     6.13      6.13      0.0  
                     TamFw                      YES     6.13      6.13      0.0  
                     TamFwGolden                YES     6.11      6.11      0.0  
                     TamFwGolden                YES     6.11      6.11      0.0  
--------------------------------------------------------------------------------
NCS1010-SA           EITU-ADMConfig             NO      1.04      1.04      0.0  
                     EITU-ADMConfig             NO      2.10      2.10      1.0  
                     EITU-ADMConfig             NO      1.04      1.04      0.0  
                     EITU-ADMConfig             NO      2.10      2.10      1.0  
                     IoFpga                     NO      1.04      1.04      0.0  
                     IoFpga                     NO      1.04      1.04      0.0  
                     IoFpgaGolden               NO      1.01      1.01      0.0  
                     IoFpgaGolden               NO      1.01      1.01      0.0  
                     SsdIntelS4510              YES    11.32     11.32      0.0  
                     SsdIntelS4510              YES    11.32     11.32      0.0  
                     SsdMicron5300              YES     0.01      0.01      0.0  
                     SsdMicron5300              YES     0.01      0.01      0.0  
                     SsdSmartModular            YES    13.06     13.06      0.0  
                     SsdSmartModular            YES    13.06     13.06      0.0  
--------------------------------------------------------------------------------
NCS1K-ILA-2R-C       ILA                        NO      1.00      1.00      0.1  
                     ILA                        NO      0.23      0.23     99.1  
                     Raman-1                    NO      1.00      1.00      0.1  
                     Raman-1                    NO      0.23      0.23     99.1  
                     Raman-2                    NO      1.00      1.00      0.1  
                     Raman-2                    NO      0.23      0.23     99.1  
--------------------------------------------------------------------------------
NCS1K-ILA-C          ILA                        NO      1.00      1.00      0.1  
                     ILA                        NO      0.23      0.23     99.1  
--------------------------------------------------------------------------------
NCS1K-ILA-R-C        ILA                        NO      1.00      1.00      0.1  
                     ILA                        NO      0.23      0.23     99.1  
                     Raman-1                    NO      1.00      1.00      0.1  
                     Raman-1                    NO      0.23      0.23     99.1  
--------------------------------------------------------------------------------
NCS1K-OLT-C          OLT                        NO      1.00      1.00      0.1  
                     OLT                        NO      0.23      0.23     99.1  
--------------------------------------------------------------------------------
NCS1K-OLT-R-C        OLT                        NO      1.00      1.00      0.1  
                     OLT                        NO      0.23      0.23     99.1  
                     Raman-1                    NO      1.00      1.00      0.1  
                     Raman-1                    NO      0.23      0.23     99.1  

show hw-module fpd

To display the firmware information of various hardware components of NCS 1010, use the show hw-module fpd command in Cisco IOS XR mode.

show hw-module fpd [ fpd-name ]

Syntax Description

fpd-name

(Optional) Name of the FPD.

Command Default

Firmware information of all the hardware components is displayed.

Command Modes

Cisco IOS XR EXEC

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example shows sample output from the show hw-module fpd command.

RP/0/RP0/CPU0:ios# show hw-module fpd                                                                                                                     
Wed Jun 29 08:50:21.057 UTC

Auto-upgrade:Disabled
                                                                         FPD Versions
                                                                        ==============
Location   Card type             HWver FPD device       ATR Status    Running   Programd  Reload Loc  
------------------------------------------------------------------------------------------------------
0/RP0/CPU0 NCS1010-CNTLR-K9      1.0   ADMConfig            CURRENT    3.40    3.40       NOT REQ
0/RP0/CPU0 NCS1010-CNTLR-K9      1.0   BIOS              S  CURRENT    4.10    4.10         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.0   BIOS-Golden      BS  CURRENT            4.10         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.0   CpuFpga           S  CURRENT    1.02    1.02         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.0   CpuFpgaGolden    BS  CURRENT            1.01         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.0   SsdIntelS4510     S  CURRENT   11.32   11.32         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.0   TamFw             S  CURRENT    6.13    6.13         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.0   TamFwGolden      BS  CURRENT            6.11         0/RP0
0/PM0      NCS1010-AC-PSU        0.0   AP-PriMCU            CURRENT    1.03    1.03       NOT REQ
0/PM0      NCS1010-AC-PSU        0.0   AP-SecMCU            CURRENT    2.01    2.01       NOT REQ
0/PM1      NCS1010-AC-PSU        0.0   AP-PriMCU            CURRENT    1.03    1.03       NOT REQ
0/PM1      NCS1010-AC-PSU        0.0   AP-SecMCU            CURRENT    2.01    2.01       NOT REQ
0/0/NXR0   NCS1K-ILA-C           1.0   ILA               S  CURRENT    1.00    1.00       NOT REQ
0/Rack     NCS1010-SA            1.0   EITU-ADMConfig       CURRENT    2.10    2.10       NOT REQ
0/Rack     NCS1010-SA            1.0   IoFpga            S  CURRENT    1.04    1.04       NOT REQ
0/Rack     NCS1010-SA            1.0   IoFpgaGolden     BS  CURRENT            1.01       NOT REQ
0/Rack     NCS1010-SA            1.0   SsdIntelS4510     S  CURRENT   11.32   11.32        0/Rack
 

show inventory

To retrieve and display the physical inventory information of the system, use the show inventory command in Cisco IOS XR mode.

show inventory [ WORD | all | chassis | details | fan | location | power ] [ raw | vendor-type ]

Syntax Description

WORD

(Optional) Displays partially qualified location specification.

all

(Optional)Displays inventory information for all the physical entities.

chassis

(Optional) Displays inventory information for the entire chassis.

details

(Optional) Displays detailed entity information.

fan

(Optional) Displays inventory information for the fans.

location| location

(Optional) Displays inventory information for a specific node, or for all nodes in the chassis.

power

(Optional) Displays inventory information for the power supply.

raw

(Optional) Displays raw information about the chassis for diagnostic purposes.

vendor-type

(Optional) Displays vendor-type information.

Command Default

All hardware inventory information is displayed.

Command Modes

Cisco IOS XR EXEC

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Enter the show inventory command with the raw keyword to display every RFC 2737 entity installed in NCS 1020, including those without a PID, unique device identifier (UDI), or other physical identification. The raw keyword is primarily intended for troubleshooting problems with the show inventory command itself.

Examples

The following examples show sample output from the show inventory command in both EXEC and Administration EXEC modes.

sysadmin-vm:0_RP0# show inventory

RP/0/RP0/CPU0:ios#show inventory

Mon May  6 16:38:33.857 IST

 

NAME: "Rack 0", DESCR: "NCS 1020 Shelf Assembly"

PID: NCS1020-SA        , VID: V00, SN: FCB2749B0FD

 

NAME: "0/RP0/CPU0", DESCR: "NCS 1010, 1012, 1020 Controller with 9600bps console rate"

PID: NCS1010-CTR2-B-K9 , VID: V00, SN: FCB2748B01S

 

NAME: "0/RP0-PTP0", DESCR: "Cisco Pluggable Optics Module"

PID: ONS-SI-GE-LX      , VID: V01, SN: AGC1703UE1M

 

NAME: "0/RP0-PTP1", DESCR: "Cisco Pluggable Optics Module"

PID: GLC-SX-MMD        , VID: V01, SN: OPM221407E5

 

NAME: "0/RP0-PTP2", DESCR: "Cisco Pluggable Optics Module"

PID: SFP-GE-S          , VID: V01, SN: FNS17040APG

 

NAME: "0/RP0-PTP3", DESCR: "Cisco Pluggable Optics Module"

PID: ONS-SI-GE-LX      , VID: V02, SN: FNS19170MGZ

 

NAME: "0/0/NXR0", DESCR: "NCS 1010 Optical Line Terminal - C-band, enhanced"

PID: NCS1K-E-OLT-C     , VID: V01, SN: FCB2721B1DP

 

NAME: "0/9/NXR0", DESCR: "Network Convergence System 1014 Filler"

PID: NCS1K14-BLANK     , VID: V01, SN: N/A

 

NAME: "0/1/NXR0", DESCR: "Network Convergence System 1010 Passive Filler"

PID: NCS1010-FLR-P     , VID: V01, SN: N/A

 

NAME: "0/2/NXR0", DESCR: "NCS 1014 16 port Colorless Direct attach LC with EDFA C-band"

PID: NCS1K14-CCMD-16-C , VID: V01, SN: FCB2749B06U

 

NAME: "0/3/NXR0", DESCR: "NCS 1014 16 port Colorless Direct attach LC with EDFA C-band"

PID: NCS1K14-CCMD-16-C , VID: V00, SN: FCB2744B0FA

 

NAME: "0/4/NXR0", DESCR: "Network Convergence System 1014 Filler"

PID: NCS1K14-BLANK     , VID: V01, SN: N/A

 

NAME: "0/5/NXR0", DESCR: "Network Convergence System 1014 Filler"

PID: NCS1K14-BLANK     , VID: V01, SN: N/A

 

NAME: "0/6/NXR0", DESCR: "Network Convergence System 1014 Filler"

PID: NCS1K14-BLANK     , VID: V01, SN: N/A

 

NAME: "0/7/NXR0", DESCR: "Network Convergence System 1014 Filler"

PID: NCS1K14-BLANK     , VID: V01, SN: N/A

 

NAME: "0/8/NXR0", DESCR: "Network Convergence System 1014 Filler"

PID: NCS1K14-BLANK     , VID: V01, SN: N/A

 

NAME: "0/FT0", DESCR: "NCS1010 - Shelf Fan"

PID: NCS1010-FAN       , VID: V01, SN: FCB2719B0WP

 

NAME: "0/FT1", DESCR: "NCS1010 - Shelf Fan"

PID: NCS1010-FAN       , VID: V01, SN: FCB2720B2H2

 

NAME: "0/FT4", DESCR: "NCS 1020 FAN Tray"

PID: NCS1020-FAN       , VID: V00, SN: FCB2752B05V

 

NAME: "0/FT5", DESCR: "NCS 1020 FAN Tray"

PID: NCS1020-FAN       , VID: V00, SN: FCB2752B05W

 

NAME: "0/FT6", DESCR: "NCS 1020 FAN Tray"

PID: NCS1020-FAN       , VID: V00, SN: FCB2752B08C

 

NAME: "0/FT7", DESCR: "NCS 1020 FAN Tray"

PID: NCS1020-FAN       , VID: V00, SN: FCB2752B072

 

NAME: "0/PM0", DESCR: "Network Convergence System 1004 AC Power Supply Unit 2.5KW"

PID: NCS1K4-AC-PSU-2   , VID: V01, SN: POG27430N29

 

NAME: "0/PM1", DESCR: "Network Convergence System 1004 AC Power Supply Unit 2.5KW"

PID: NCS1K4-AC-PSU-2   , VID: V01, SN: POG27430N1P

show license all

To display all licensing information, use the show license all command. This command displays status, authorization, UDI, and usage information, all combined.

show license all

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Administration for Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None.

Examples

This example shows you how to use the show license all command, and the sample output.

RP/0/RP0/CPU0:ios#show license all
Fri Jul 15 05:32:02.678 UTC
Smart Licensing Status
======================
Smart Licensing is ENABLED
Registration:
Status: REGISTERED
Smart Account: InternalTestDemoAccount8.cisco.com
Virtual Account: NCS1010-PROD
Export-Controlled Functionality: ALLOWED
Initial Registration: SUCCEEDED on Jul 15 2022 04:58:24 UTC
Last Renewal Attempt: None
Next Renewal Attempt: Jan 11 2023 04:58:23 UTC
Registration Expires: Jul 15 2023 04:53:20 UTC
License Authorization:
Status: AUTHORIZED on Jul 15 2022 04:58:40 UTC
Last Communication Attempt: SUCCEEDED on Jul 15 2022 04:58:40 UTC
Next Communication Attempt: Aug 14 2022 04:58:40 UTC
Communication Deadline: Oct 13 2022 04:53:41 UTC
Export Authorization Key:
Features Authorized:
<none>
Utility:
Status: DISABLED
Data Privacy:
Sending Hostname: yes
Callhome hostname privacy: DISABLED
Smart Licensing hostname privacy: DISABLED
Version privacy: DISABLED
Transport:
Type: Callhome
Miscellaneous:
Smart Licensing
10
Smart Licensing
Verify Smart Licensing Configuration
REVIEW DRAFT - CISCO CONFIDENTIAL
Custom Id: <empty>
License Usage
=============
NCS1010 - Essentials - OLT RTU (NCS1010_ESS_OLT_RTU):
Description: NCS1010 - Essentials Tier - Optical Line Terminal RTU (Per Port)
Count: 2
Version: 1.0
Status: AUTHORIZED
Export status: NOT RESTRICTED
NCS1010 - Essentials - OLT SIA (NCS1010_ESS_OLT_SIA):
Description: NCS1010 - Essentials Subscription - Optical Line Terminal - SIA
(Per Port)
Count: 2
Version: 1.0
Status: AUTHORIZED
Export status: NOT RESTRICTED
Product Information
===================
UDI: PID:NCS1010-SA,SN:FCB2546B08T
Agent Version
=============
Smart Agent for Licensing: 5.4.16_rel/63
Reservation Info
================
License reservation: DISABLED
    

show license summary

To display the license summary, use the show license summary command.

show license summary

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Administration for Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None.

Examples

This example shows you how to use the show license summary command, and the sample output.

 RP/0/RP0/CPU0:ios#show license summary 
                    
                    Tue Jul 19 15:21:49.227 UTC
                    
                    Smart Licensing is ENABLED
                    License Reservation is ENABLED
                    
                    Registration:
                    Status: REGISTERED - SPECIFIC LICENSE RESERVATION
                    Export-Controlled Functionality: ALLOWED
                    
                    License Authorization: 
                    Status: AUTHORIZED - RESERVED
                    
                    License Usage:
                    License                 Entitlement Tag               Count Status
                    -----------------------------------------------------------------------------
                    NCS1010 - Essentials... (NCS1010_ESS_OLT_RTU)             3 AUTHORIZED
                    NCS1010 - Essentials... (NCS1010_ESS_OLT_SIA)             3 AUTHORIZED
                    RP/0/RP0/CPU0:P2A_DT_08#show license usage   
                    Tue Jul 19 15:22:11.234 UTC
                    
                    License Authorization: 
                    Status: AUTHORIZED - RESERVED on Jul 19 2022 15:21:24 UTC
                    
                    NCS1010 - Essentials - OLT RTU (NCS1010_ESS_OLT_RTU):
                    Description: NCS1010 - Essentials Tier - Optical Line Terminal RTU (Per Port)
                    Count: 3
                    Version: 1.0
                    Status: AUTHORIZED
                    Export status: NOT RESTRICTED
                    Reservation: 
                    Reservation status: SPECIFIC INSTALLED
                    Total reserved count: 3
                    
                    NCS1010 - Essentials - OLT SIA (NCS1010_ESS_OLT_SIA):
                    Description: NCS1010 - Essentials Subscription - Optical Line Terminal - SIA 
                    (Per Port)
                    Count: 3
                    Version: 1.0
                    Status: AUTHORIZED
                    Export status: NOT RESTRICTED
                    Reservation: 
                    Reservation status: SPECIFIC INSTALLED
                    Total reserved count: 3
                    RP/0/RP0/CPU0:P2A_DT_08#show license platform summary 
                    Tue Jul 19 15:22:35.859 UTC
                    Collection: LAST: (unavailable)
                    NEXT: (pending in 1 minute(s))
                    Reporting:  LAST: (unavailable)
                    NEXT: (pending in 1 minute(s))
                    **********************************IMPORTANT************************************
                    SIA Status: Out of Compliance(Remaining Grace Period: 89 days, 23 hours)
                    SIA license(s) status is Not Authorized. 
                    SW Upgrade will still be allowed as SIA Grace Period is remaining
                    *******************************************************************************
                    Count
                    Feature/Area     Entitlement                                     Last Next
                    ============ =================================================== ==== ====
                    FCM          NCS1010 - Essentials Tier - Optical Line Terminal R    3    0
                    FCM          NCS1010 - Essentials Subscription - Optical Line Te    3    0
                

show logging onboard

Use the show logging onboard command to view the Onboard Failure Logs (OBFL).

show logging onboard { alarm | | | location | location }

Syntax Description

alarm

Displays the alarm events.

location location

Specify the location of the hardware module.

Command Modes

User EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example shows how to display the Onboard Failure Logs (OBFL) details for the show logging onboard command.

RP/0/RPO/CPUO:PIAL 05#show logging onboard alarm location 0/ rp0/CPUO
Thu Feb 9 11:34:25.158 UTC 
OBFL alarm information for: 0/RPO/CPU0

2022-12-09 09:50:31 DECLARE     ALARM MAJOR    Power Group redundancy lost
2022-12-14 11:25:41 DECLARE     ALARM MAJOR    Power Group redundancy lost 
2022-12-09 09:50:31 DECLARE     ALARM MAJOR    Power Group redundancy lost
2022-12-14 11:25:41 DECLARE     ALARM MAJOR    Power Group redundancy lost
2023-02-09 11:33:05 DECLARE     ALARM CRITICAL PHY1-MDIO-ACCESS-ERROR Phyl MDI0 access failure detected

show license platform detail

To display the detailed summary of all Flexible Consumption Models (FCM) licenses in the NCS 1010 platform, use the show license platform detail command.

show license platform detail

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Administration for Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None.

Examples

This example shows you how to use the show license platform detail command, and the sample output.

RP/0/RP0/CPU0:ios#show license platform detail 
Mon Jul 18 10:52:46.333 UTC
Collection: LAST: Mon Jul 18 2022 10:52:07 UTC
            NEXT: Mon Jul 18 2022 10:54:07 UTC
Reporting:  LAST: Mon Jul 18 2022 10:52:07 UTC
            NEXT: Mon Jul 18 2022 10:54:07 UTC
SIA Status: In Compliance
Parameters: Collection interval:           2 minute(s)
            Reporting  interval:           2 minute(s)
            Throughput gauge:        1000000 Kbps


=================================================
Feature/Area 'FCM'
   Name:  FCM
   Status:   ACTIVE
   Flags:  
   

   [ 1] Name:  NCS1010 - Essentials Tier - In-Line Amplifier RTU
        Entitlement Tag: regid.2022-05.com.cisco.NCS1010_ESS_ILA_RTU,1.0_9b4322b1-bff3-4ddf-944c-16ec9aaab1cc
        Count: Last reported:    0
               Next report:      0
   [ 2] Name:  NCS1010 - Essentials Subscription - In-Line Amplifier - SIA
        Entitlement Tag: regid.2022-05.com.cisco.NCS1010_ESS_ILA_SIA,1.0_67243ac7-1a7c-41e4-a160-f13df80fd0e4
        Count: Last reported:    0
               Next report:      0
   [ 3] Name:  NCS1010 - Essentials Tier - Optical Line Terminal RTU (Per Port)
        Entitlement Tag: regid.2022-05.com.cisco.NCS1010_ESS_OLT_RTU,1.0_e4309530-2085-40e6-9aa6-5f3137ff49b2
        Count: Last reported:    9
               Next report:      0
   [ 4] Name:  NCS1010 - Essentials Subscription - Optical Line Terminal - SIA (Per Port)
        Entitlement Tag: regid.2022-05.com.cisco.NCS1010_ESS_OLT_SIA,1.0_b3c976c1-e509-474f-8cac-b9db62f28f2b
        Count: Last reported:    9
               Next report:      0
   [ 5] Name:  NCS1010 - Advantage Tier- In-Line Amplifier RTU
        Entitlement Tag: regid.2022-05.com.cisco.NCS1010_ADV_ILA_RTU,1.0_cf1746b7-def4-4c0e-ab90-de30614507d8
        Count: Last reported:    0
               Next report:      0
   [ 6] Name:  NCS1010 - Advantage Subscription - In-Line Amplifier - SIA
        Entitlement Tag: regid.2022-05.com.cisco.NCS1010_ADV_ILA_SIA,1.0_ea769b05-9363-47dd-9991-2122c37479eb
        Count: Last reported:    0
               Next report:      0
   [ 7] Name:  NCS1010 - Advantage Tier - Optical Line Terminal RTU (Per Port)
        Entitlement Tag: regid.2022-05.com.cisco.NCS1010_ADV_OLT_RTU,1.0_7a6ce8f3-3336-4ce2-8803-431227dabfff
        Count: Last reported:    0
               Next report:      0
   [ 8] Name:  NCS1010 - Advantage Subscription - Optical Line Terminal - SIA (Per Port)
        Entitlement Tag: regid.2022-05.com.cisco.NCS1010_ADV_OLT_SIA,1.0_5f283f1c-143e-4c6e-9af7-73e088fb77a5
        Count: Last reported:    0
               Next report:      0
    

show license platform summary

To display the summary of FCM licenses in the NCS 1010 platform, use the show license platform summary command.

show license platform summary

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Administration for Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None.

Examples

This example shows you how to use the show license platform summary command, and the sample output.

RP/0/RP0/CPU0:ios#show license platform summary 
Mon Jul 18 10:50:59.263 UTC
Collection: LAST: Mon Jul 18 2022 10:50:07 UTC
            NEXT: Mon Jul 18 2022 10:52:07 UTC
Reporting:  LAST: Mon Jul 18 2022 10:50:07 UTC
            NEXT: Mon Jul 18 2022 10:52:07 UTC
**********************************IMPORTANT************************************
SIA Status: Out of Compliance(Remaining Grace Period: 89 days, 23 hours)
            Device is in Authorization Expired state. 
            SW Upgrade will still be allowed as SIA Grace Period is remaining
*******************************************************************************
                                                                   Count
Feature/Area     Entitlement                                     Last Next
============ =================================================== ==== ====
FCM          NCS1010 - Essentials Tier - Optical Line Terminal R    9    0
FCM          NCS1010 - Essentials Subscription - Optical Line Te    9    0
    

show license summary

To display the license summary, use the show license summary command.

show license summary

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Administration for Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None.

Examples

This example shows you how to use the show license summary command, and the sample output.

 RP/0/RP0/CPU0:ios#show license summary
Tue Jul 19 15:21:49.227 UTC
Smart Licensing is ENABLED
License Reservation is ENABLED

Registration:
  Status: REGISTERED - SPECIFIC LICENSE RESERVATION
  Export-Controlled Functionality: ALLOWED

License Authorization: 
  Status: AUTHORIZED - RESERVED

License Usage:
  License                 Entitlement Tag               Count Status
  -----------------------------------------------------------------------------
  NCS1010 - Essentials... (NCS1010_ESS_OLT_RTU)             3 AUTHORIZED
  NCS1010 - Essentials... (NCS1010_ESS_OLT_SIA)             3 AUTHORIZED
R

show license udi

To display the smart licensing UDI, use the show license udi command.

show license udi

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

None

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None.

Examples

This example shows you how to use the show license udi command, and the sample output.

RP/0/RP0/CPU0:ios#show license udi
Tue Jul 19 13:43:19.731 UTC
UDI: PID:NCS1010-SA,SN:FCB2546B08T
        

show license usage

To display the license usage count, use the show license usage command.

show license usage

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Administration for Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None.

Examples

This example shows you how to use the show license usage command, and the sample output.

 RP/0/RP0/CPU0:iso#show license usage
Fri Jul 15 08:17:40.048 UTC
License Authorization:
Status: OUT OF COMPLIANCE on Jul 15 2022 07:01:00 UTC
NCS1010 - Essentials - OLT RTU (NCS1010_ESS_OLT_RTU):
Description: NCS1010 - Essentials Tier - Optical Line Terminal RTU (Per Port)
Count: 32
Version: 1.0
Status: OUT OF COMPLIANCE
Export status: NOT RESTRICTED
NCS1010 - Essentials - OLT SIA (NCS1010_ESS_OLT_SIA):
Description: NCS1010 - Essentials Subscription - Optical Line Terminal - SIA
Smart Licensing
13
Smart Licensing
Verify Smart Licensing Configuration
REVIEW DRAFT - CISCO CONFIDENTIAL
(Per Port)
Count: 32
Version: 1.0
Status: OUT OF COMPLIANCE
Export status: NOT RESTRICTED
    

show ntp associations

To display the status of Network Time Protocol (NTP) associations, use the show ntp associations command in privileged EXEC mode.

show ntp associations [detail] [ location node-id ]

Syntax Description

detail

(Optional) Displays detailed information about each NTP association.

location node-id

(Optional) Displays the status of NTP associations from the designated node. The node-id argument is entered in the rack/ slot notation.

Command Default

None

Command Modes

EXEC

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Output for the show ntp associations command is displayed only if NTP is configured.

Task ID

Task ID

Operations

ip-services

read

Examples

This example shows sample output from the show ntp associations command:


RP/0/RP0/CPU0:ios#show ntp associations
Sun Nov 5 15:14:44.128 UTC

address ref clock st when poll reach delay offset disp
*~203.0.113.51 10.64.58.50 2 81 128 377 1.84 7.802 2.129
* sys_peer, # selected, + candidate, - outlayer, x falseticker, ~ configured
      
Table 1. show ntp associations Field Descriptions

Field

Description

Peer has been declared the system peer and lends its variables to the system variables.

#

A pound sign (#) displayed next to a configured peer indicates that the router does not synchronize with the peer even though NTP request and response packets are exchanged.

In this case, check the output of the show ntp associations detail command or the NTP debugs to see why the clocks are not synchronized.

Use the show ntp associations detail and show ntp status commands to obtain additional information about the state of NTP.

One possible reason for the # sign is that the NTP client clock differs by more than 4000 seconds from the NTP server clock. On Cisco routers, a time difference of greater than 4000 seconds is considered out of range and prevents the router from synchronization to the server. This does not apply when you first configure an NTP peer on a Cisco router or on reload. In this case, the NTP client clock is changed to match the NTP server clock. Verify the time zone of the client clock; local time is displayed, but time values in NTP messages are in UTC (GMT) time zone. You can manually change the client clock to within a few minutes of the NTP server clock.

+

Peer is a survivor and a candidate for the combining algorithm.

-

Peer is discarded by the clustering algorithm as an outlier.

x

Peer is discarded by the intersection algorithm as a falseticker.

~

Indicates peer is statically configured.

address

IPv4 or IPv6 address of the peer. If a nondefault VRF is configured for the peer, the VRF follows the address.

ref clock

Reference clock type or address for the peer.

st

Stratum setting for the peer.

when

Time since last NTP packet was received from peer, in milliseconds.

poll

Polling interval between NTP poll packets, in seconds. As the NTP server and client are better synced (and there are no dropped packets), this number increases to a maximum of 1024.

reach

Peer reachability (bit string, in octal).

The reach field is a circular bit buffer. It gives you the status of the last eight NTP messages (eight bits in octal is 377, so you want to see a reach field value of 377).

If an NTP response packet is lost, the lost packet is tracked over the next eight NTP update intervals in the reach field.

delay

Round-trip delay to peer, in milliseconds.

offset

Relative time difference between the client time and server time, in milliseconds. The client slows down or speeds up its clock to match the server time value.

The offset decreases toward zero over time. It likely never reaches zero since the packet delay between the client and server is never exactly the same. Therefore, the client NTP cannot ever exactly match its clock with the server.

If there is an asterisk (*) next to a configured peer, then you are syncronized to this peer and use them as the primary clock.

disp

Dispersion.

This example shows sample output from the show ntp associations command with the detail keyword:

RP/0/RP0/CPU0:ios#show ntp associations detail
Sun Nov 5 15:14:48.763 UTC

203.0.113.51 configured, our_master, stratum 2
ref ID 10.64.58.50, time E8F22BB9.79D4A841 (14:56:57.475 UTC Sun Nov 5 2023)
our mode client, peer mode server, our poll intvl 128, peer poll intvl 128
root delay 0.6866 msec, root disp 1.04, reach 377, sync dist 6.2590
delay 1.84 msec, offset 7.802 msec, dispersion 2.129
precision 2**23, version 4
org time E8F22F92.B647E8FC (15:13:22.712 UTC Sun Nov 5 2023)
rcv time E8F22F92.B88F303C (15:13:22.720 UTC Sun Nov 5 2023)
xmt time E8F22F92.B88F303C (15:13:22.720 UTC Sun Nov 5 2023)
filtdelay = 1.844 1.772 1.983 1.954 1.945 2.000 1.902 1.778
filtoffset = 7.857 7.802 8.065 8.063 8.332 8.397 8.664 8.684
filterror = 0.000 0.060 1.995 2.055 4.050 4.110 6.060 6.120
Table 2. show ntp associations detail Field Descriptions

Field

Descriptions

vrf

Nondefault VRF, if specified for this peer.

configured

Statically configured peer.

dynamic

Dynamically discovered peer.

our_master

Synchronization of the local machine to this peer.

sane

Passing of basic sanity checks by this peer.

ref ID

Address of machine to which the peer is synchronized.

time

Last time stamp that the peer received from its master.

our mode

Mode relative to peer (active/passive/client/server/bdcast/bdcast client).

peer mode

Mode of peer relative.

our poll intvl

Poll interval to peer.

peer poll intvl

Poll interval of interval.

root delay

Delay along path to root (ultimate stratum 1 time source).

root disp

Dispersion of path to root.

reach

Peer reachability (bit string in octal).

sync dist

Peer synchronization distance.

delay

Round-trip delay to peer.

offset

Offset of peer clock relative to this clock.

dispersion

Dispersion of peer clock.

precision

Precision of peer clock in (Hertz) Hz.

version

NTP version number that peer is using.

org time

Originate time stamp.

rcv time

Receive time stamp.

xmt time

Transmit time stamp.

filtdelay

Round-trip delay of each sample, in milliseconds.

filtoffset

Clock offset of each sample, in milliseconds.

filterror

Approximate error of each sample.

show ntp status

To display the status of Network Time Protocol (NTP), use the show ntp status command in XR EXEC mode.

show ntp status [ location node-id ]

Syntax Description

location node-id

(Optional) Displays the status of NTP from the designated node. The node-id argument is entered in the rack/ slot notation.

Command Default

None

Command Modes

XR EXEC mode

Command History

Release

Modification

Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Task ID

Task ID

Operations

ip-services

read

Examples

This example shows sample output from the show ntp status command:


RP/0/RP0/CPU0:ios#show ntp status
Sun Nov 5 15:14:36.949 UTC

Clock is synchronized, stratum 3, reference is 203.0.113..51
nominal freq is 1000000000.0000 Hz, actual freq is 44881851.3383 Hz, precision is 2**24
reference time is E8F22D7A.AB020D97 (15:04:26.668 UTC Sun Nov 5 2023)
clock offset is 9.690 msec, root delay is 2.553 msec
root dispersion is 24.15 msec, peer dispersion is 2.13 msec
loopfilter state is 'CTRL' (Normal Controlled Loop), drift is 0.0000212807 s/s
system poll interval is 128, last update was 610 sec ago
authenticate is disabled, panic handling is disabled,
hostname resolution retry interval is 1440 minutes.
  
Table 3. show ntp status Field Descriptions

Field

Description

synchronized

Synchronized system to an NTP peer.

stratum

NTP stratum of this system.

reference

IPv4 address or first 32 bits of the MD5 hash of the IPv6 address of the peer to which clock is synchronized.

nominal freq

Nominal frequency in Hertz (Hz) of the system hardware clock.

actual freq

Measured frequency in Hz of the system hardware clock.

precision

Precision of the clock of this system in Hz.

reference time

Reference time stamp.

clock offset

Offset of clock to synchronized peer, in milliseconds.

root delay

Total delay along path to root clock, in milliseconds.

root dispersion

Dispersion of root path.

peer dispersion

Dispersion of synchronized peer.

loopfilter state

The state of the clock state machine transition function.

drift

Drift of the hardware clock.

system poll interval

Poll interval of the peer.

last update

Time the router last updated its NTP information.

show olc apc

Use the show olc apc command to view APC status.

show olc apc { controller Ots | | R/S/I/P }

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

controller Ots

Use this parameter to view the information for a particular controller.

Command Modes

User EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following sample is an output of show olc apc command.

RP/0/RP0/CPU0:OLT1#show olc apc

Controller      : Ots0/0/0/0
APC Status      : WORKING

Node RID        : 10.1.1.1
Internal State  : IDLE

Node RID        : 10.99.1.2
Internal State  : IDLE

Node RID        : 10.99.2.2
Internal State  : IDLE

Node RID        : 10.99.4.1
Internal State  : IDLE

Node RID        : 10.1.1.5
Internal State  : DISCREPANCY

show olc apc-local

To view the local status of APC on each node, use the show olc apc-local command.

show olc apc-local { regulation-info { controller Ots | | R/S/I/P | { tx | rx } } | target-psd-profile } { controller Ots | | R/S/I/P }

Syntax Description

regulation-info

Displays APC regulation information.

target-psd-profile

Displays target PSD profile information

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

controller Ots

Use this parameter to view the information for a particular controller.

Command Modes

User EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following sample is an output of show olc apc-local command.

RP/0/RP0/CPU0:ios#show olc apc-local
Mon Apr 11 06:59:14.679 UTC

Controller : Ots0/0/0/0

TX Status : ENABLED
RX Status : ENABLED

The following sample is an output of show olc apc-local target-psd-profile command.

RP/0/RP0/CPU0:ios#show olc apc-local target-psd-profile
Tue Apr 26 10:19:24.910 UTC
Controller          : Ots0/0/0/0
Target PSD source   : Configuration
-------------------------------------------------------------------------------
Setpoint                Frequency                        Target PSD
                          (THz)                        (dBm/12.5 GHz)
-------------------------------------------------------------------------------
01                    191.337494                           15.0
02                    191.488678                           15.0
03                    191.639847                           -4.1
04                    191.791016                           -4.1
05                    191.942184                           -4.1
06                    192.093353                           -4.1
07                    192.244537                           -4.1
08                    192.395706                           -4.1
09                    192.546875                           -4.1
10                    192.698044                           -4.1
11                    192.849213                           -4.1
12                    193.000397                           -4.1
13                    193.151566                           -4.1
14                    193.302734                           -4.1
15                    193.453903                           -4.1
16                    193.605072                           -4.1
17                    193.756256                           -4.1
18                    193.907425                           -4.1
19                    194.058594                           -4.1
20                    194.209763                           -4.1
21                    194.360931                           -4.1
22                    194.512115                           -4.1
23                    194.663284                           -4.1
24                    194.814453                           -4.1
25                    194.965622                           -4.1
26                    195.116791                           -4.1
27                    195.267975                           -4.1
28                    195.419144                           -4.1
29                    195.570312                           -4.1
30                    195.721481                           -4.1
31                    195.872650                           -4.1
32                    196.023834                           -4.1
33                    196.175003                           -4.1

The following sample is an output ofshow olc apc-local regulation-info controller ots 0/0/0/0 txcommand.

RP/0/RP0/CPU0:ios#show olc apc-local regulation-info controller ots 0/0/0/0 tx
Wed Jul  6 05:01:45.177 UTC
Controller            : Ots0/0/0/0
Domain Manager        : 10.1.1.1
Internal Status       : OOR
Direction            : TX
PSD Minumum          : -24.0 (dBm/12.5 GHz)
Gain Range           : Normal
Last Correction      : 2022-07-06 05:01:28

  Device Parameters                 Min   Max  Configuration Operational
===========================================================================
  Egress Ampli Gain (dB)           :15.4  29.4 19.5          19.5 
  Egress Ampli Tilt (dB)           :-5.0  3.1  -2.2          -2.2 
  TX Ampli Power (dBm)             : -    22.4  -            21.4
  TX VOA Attenuation (dB)          :0.0   20.0 0.0           0.0
  Egress WSS/DGE Attenuation (dB)  :0.0   25.0  -             - 


Channel Center Channel Channel Channel Spectrum   Ampli-Input      Target       Current    Discrepancy Channel Slice
  Frequency     Width    ID    Source  Slice Num      PSD           PSD           PSD                   Attn Config
    (THz)       (GHz)                            (dBm/12.5 GHz)(dBm/12.5 GHz)(dBm/12.5 GHz)    (dB)        (dB)
====================================================================================================================
 191.375000    75.00     1      OCh       13          -23.2         -4.6          -4.9         0.2        7.1
 191.449997    75.00     -      ASE       37          -23.0         -4.6          -4.7         0.1        9.2
 191.524994    75.00     -      ASE       61          -23.1         -4.6          -4.7         0.1        9.3
 191.600006    75.00     4      OCh       85          -23.1         -4.5          -4.7         0.1        8.0
 191.675003    75.00     -      ASE       109         -23.0         -4.5          -4.5         0.0        9.1
 191.750000    75.00     6      OCh       133         -23.0         -4.4          -4.6         0.1        8.0
 191.824997    75.00     -      ASE       157         -23.1         -4.4          -4.6         0.1        9.3
 191.899994    75.00     8      OCh       181         -23.0         -4.4          -4.4         0.0        8.0
 191.975006    75.00     -      ASE       205         -23.0         -4.3          -4.5         0.1        9.1
 192.050003    75.00     10     OCh       229         -23.0         -4.3          -4.5         0.1        8.2
 192.125000    75.00     -      ASE       253         -22.9         -4.3          -4.3         0.0        9.0
 192.199997    75.00     12     OCh       277         -22.8         -4.2          -4.3         0.0        8.3
 192.274994    75.00     -      ASE       301         -22.9         -4.2          -4.4         0.1        9.0
 192.350006    75.00     14     OCh       325         -22.6         -4.2          -4.2         0.0        8.3
 192.425003    75.00     -      ASE       349         -22.8         -4.2          -4.3         0.1        8.7
 192.500000    75.00     16     OCh       373         -22.4         -4.1          -3.9         -0.2       8.1
 192.574997    75.00     -      ASE       397         -22.7         -4.1          -4.2         0.1        8.6
 192.649994    75.00     18     OCh       421         -22.6         -4.1          -4.2         0.1        8.1
 192.725006    75.00     -      ASE       445         -22.7         -4.0          -4.2         0.1        8.6
 192.800003    75.00     20     OCh       469         -22.7         -4.0          -4.1         0.1        7.9
 192.875000    75.00     -      ASE       493         -22.6         -4.0          -4.0         0.0        8.4
 192.949997    75.00     22     OCh       517         -22.6         -3.9          -4.1         0.1        7.6
 193.024994    75.00     -      ASE       541         -22.5         -3.9          -4.0         0.1        8.2
 193.100006    75.00     24     OCh       565         -22.7         -3.8          -4.0         0.1        7.5
 193.175003    75.00     -      ASE       589         -22.7         -3.8          -4.0         0.1        8.2
 193.250000    75.00     26     OCh       613         -22.5         -3.8          -3.9         0.1        7.2
 193.324997    75.00     -      ASE       637         -22.6         -3.8          -4.0         0.2        8.1
 193.399994    75.00     28     OCh       661         -22.7         -3.7          -3.9         0.1        7.2
 193.475006    75.00     -      ASE       685         -22.5         -3.7          -3.8         0.1        8.0
 193.550003    75.00     30     OCh       709         -22.7         -3.7          -3.8         0.1        7.0
 193.625000    75.00     -      ASE       733         -22.7         -3.6          -3.8         0.1        8.1
 193.699997    75.00     32     OCh       757         -22.7         -3.6          -3.7         0.1        6.7
 193.774994    75.00     -      ASE       781         -22.7         -3.5          -3.7         0.1        8.2
 193.850006    75.00     34     OCh       805         -22.7         -3.5          -3.7         0.1        6.6
 193.925003    75.00     -      ASE       829         -22.7         -3.5          -3.6         0.1        8.1
 194.000000    75.00     36     OCh       853         -22.8         -3.5          -3.7         0.2        6.6
 194.074997    75.00     -      ASE       877         -22.8         -3.4          -3.6         0.1        8.3
 194.149994    75.00     38     OCh       901         -22.7         -3.4          -3.5         0.1        10.9
 194.225006    75.00     -      ASE       925         -22.8         -3.3          -3.5         0.1        8.2
 194.300003    75.00     40     OCh       949         -22.9         -3.3          -3.5         0.1        7.1
 194.375000    75.00     -      ASE       973         -22.8         -3.3          -3.4         0.1        8.4
 194.449997    75.00     42     OCh       997         -22.9         -3.2          -3.5         0.2        7.3
 194.524994    75.00     -      ASE       1021        -22.9         -3.2          -3.4         0.1        8.4
 194.600006    75.00     44     OCh       1045        -22.8         -3.2          -3.3         0.1        7.2
 194.675003    75.00     -      ASE       1069        -22.8         -3.2          -3.3         0.1        8.4
 194.750000    75.00     46     OCh       1093        -22.9         -3.1          -3.4         0.2        7.3
 194.824997    75.00     -      ASE       1117        -22.8         -3.1          -3.2         0.1        8.2
 194.899994    75.00     48     OCh       1141        -22.8         -3.0          -3.3         0.2        6.9
 194.975006    75.00     -      ASE       1165        -22.9         -3.0          -3.2         0.1        8.3
 195.050003    75.00     50     OCh       1189        -22.8         -3.0          -3.1         0.1        6.6
 195.125000    75.00     -      ASE       1213        -22.9         -3.0          -3.1         0.1        8.3
 195.199997    75.00     52     OCh       1237        -22.9         -2.9          -3.1         0.1        6.3
 195.274994    75.00     -      ASE       1261        -23.0         -2.9          -3.0         0.1        8.1
 195.350006    75.00     54     OCh       1285        -23.1         -2.8          -3.0         0.1        6.4
 195.425003    75.00     -      ASE       1309        -23.2         -2.8          -3.0         0.1        8.3
 195.500000    75.00     56     OCh       1333        -23.1         -2.8          -2.9         0.1        6.2
 195.574997    75.00     -      ASE       1357        -23.4         -2.8          -3.0         0.2        8.2
 195.649994    75.00     58     OCh       1381        -23.4         -2.7          -2.9         0.1        6.4
 195.725006    75.00     -      ASE       1405        -23.4         -2.7          -2.8         0.1        8.5
 195.800003    75.00     60     OCh       1429        -23.6         -2.7          -2.8         0.1        6.6
 195.875000    75.00     -      ASE       1453        -23.7         -2.6          -2.9         0.2        8.7
 195.949997    75.00     62     OCh       1477        -23.7         -2.6          -2.8         0.2        6.9
 196.024994    75.00     -      ASE       1501        -23.6         -2.5          -2.7         0.1        9.0
 196.100006    75.00     64     OCh       1525        -23.7         -2.5          -2.7         0.1        7.1


ASE - Noise Loaded Channel
OCh - Optical Channel

show olc band-status

Use the show olc band-statuscommand to display the status of all the nodes in the controller.

show olc band-status

Table 4. Syntax Description

This command has no keywords or arguments.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example shows how to view the status of BFR on each node.

RP/0/RP0/CPU0#sh olc band-status 
Tue Dec 13 10:45:30.594 UTC
 
Controller              : Ots0/0/0/0
Self-Band               : C-Band
BFR status              : Running
 
Node RID                : 10.1.1.1
Self IP Address         : 192.0.2.1
Self Controller         : Ots0/0/0/0
Partner IP address      : 192.0.2.2
Partner Controller      : Ots0/0/0/0
Partner link status     : UP
C-Band status           : ACTIVE
C-Band PSD              : Dual Band
L-Band status           : ACTIVE
L-Band PSD              : Dual Band

Node RID                : 10.1.1.2
Self IP Address         : 192.0.2.6
Self Controller         : Ots0/0/0/0
Partner IP address      : 192.0.2.7
Partner Controller      : Ots0/0/0/2
Partner link status     : UP
C-Band status           : ACTIVE
C-Band PSD              : Dual Band
L-Band status           : ACTIVE
L-Band PSD              : Dual Band
 
Node RID                : 10.1.1.3
Self IP Address         : 198.51.100.1
Self Controller         : Ots0/0/0/0
Partner IP address      : 198.51.100.2
Partner Controller      : Ots0/0/0/2
Partner link status     : UP
C-Band status           : ACTIVE
C-Band PSD              : Dual Band
L-Band status           : ACTIVE
L-Band PSD              : Dual Band
 
Node RID                : 10.1.1.4
Self IP Address         : 203.0.113.1
Self Controller         : Ots0/0/0/0
Partner IP address      : 203.0.113.2
Partner Controller      : Ots0/0/0/0
Partner link status     : UP
C-Band status           : ACTIVE
C-Band PSD              : Dual Band
L-Band status           : ACTIVE
L-Band PSD              : Dual Band
 
Node RID                : 10.1.1.5
Self IP Address         : 203.0.113.45
Self Controller         : Ots0/0/0/0
Partner IP address      : 203.0.113.46
Partner Controller      : Ots0/0/0/0
Partner link status     : UP
C-Band status           : ACTIVE
C-Band PSD              : Dual Band
L-Band status           : ACTIVE
L-Band PSD              : Dual Band

The following table describes the different fields that are displayed in the output of the show olc band-status command.

Status

Description

Controller

Name of the controller.

Self-Band

Name of the band.

Values:

  • C-Band

  • L-Band

  • None

BFR status

Status of BFR.

Values:

  • Running

  • Paused

  • NA

Node RID

Node router ID.

Self IP Address

IP address of the current node on which the command is running.

Note

 

This field displays NA if BFR is paused.

Self Controller

Controller details of the current node on which the command is running.

Note

 

This field displays NA if BFR is paused.

Partner IP address

IP address of the partner node that is connected to the self node in the Node RID. This IP address is used to communicate between the L-band and C-band device.

Note

 

This field displays NA if BFR is paused.

Partner Controller

Controller details of the partner node.

Note

 

This field displays NA if BFR is paused.

Partner link status

Connection status of the C and L band nodes.

Values:

  • UP

  • DOWN

Note

 

This field displays NA if BFR is paused.

C-Band status

C band node status.

Valid values:

  • ACTIVE

  • FAILED

  • RECOVERING

  • NA

Note

 

This field displays NA if BFR is paused.

C-Band PSD

The active PSD profile on the C-Band node.

Valid values:

  • Dual Band

  • Single Band

Note

 

This field displays NA if BFR is paused.

L-Band status

L band node status.

Valid values:

  • ACTIVE

  • FAILED

  • RECOVERING

  • NA

Note

 

This field displays NA if BFR is paused.

L-Band PSD

The active PSD profile on the L-Band node.

Valid values:

  • Dual Band

  • Single Band

Note

 

This field displays NA if BFR is paused.

show olc gain-estimator

Use the show olc gain-estimator command to view the gain estimation details.

show olc gain-estimator { controller Ots | | R/S/I/P }

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

controller Ots

Use this parameter to view the information for a particular controller.

Command Modes

User EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following output is a sample of the show olc gain-estimator command.

RP/0/RP0/CPU0:ios#show olc gain-estimator 
Thu May 12 09:30:39.987 UTC
Controller                          : Ots0/0/0/0
Egress  Gain Estimator Status       : IDLE
Egress  Estimated Gain              : 25.9 dB
Egress  Estimated Gain Mode         : Extended
Egress  Gain Estimation Timestamp   : 2022-05-07 09:16:53

Controller                          : Ots0/0/0/2
Egress  Gain Estimator Status       : IDLE
Egress  Estimated Gain              : 11.7 dB
Egress  Estimated Gain Mode         : Normal
Egress  Gain Estimation Timestamp   : 2022-05-07 10:13:53

The following output is a sample of the show olc gain-estimator controller ots R/S/I/P command.

RP/0/RP0/CPU0:ios#show olc gain-estimator controller Ots 0/0/0/0 
Fri Jun 10 05:47:21.119 UTC
Controller                          : Ots0/0/0/0
Ingress Gain Estimator Status       : IDLE
Ingress Estimated Gain              : 21.7 dB
Ingress Estimated Gain Mode         : Normal
Ingress Gain Estimation Timestamp   : 2022-06-10 05:46:48

show olc link-tuner

To view link tuner status and PSD computation information, use show olc link-tuner command.

show olc link-tuner { detail } { { controller Ots | | R/S/I/P } }

Syntax Description

detail

Displays link tuner status, PSD computation information, and computed total noise.

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

controller Ots

Use this parameter to view the information for a particular controller.

Command Modes

User EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following sample is an output of show olc link-tuner command.

RP/0/RP0/CPU0:ios#show olc link-tuner 
Controller          : Ots0/0/0/0
Link Tuner Status   : OPERATIONAL
Last PSD computation: 2022-05-06 10:59:51
----------------------------------------------------------------------
Setpoint            : Computed PSD
                     (dBm/12.5 GHz)
---------------------------s-------------------------------------------
01                    -5.7             
02                    -5.6             
03                    -5.6             
04                    -5.5             
05                    -5.5             
06                    -5.4             
07                    -5.4             
08                    -5.3             
09                    -5.3             
10                    -5.2             
11                    -5.2             
12                    -5.1             
13                    -5.1             
14                    -5.0             
15                    -5.0             
16                    -4.9             
17                    -4.9             
18                    -4.8             
19                    -4.8             
20                    -4.7             
21                    -4.7             
22                    -4.6             
23                    -4.6             
24                    -4.5             
25                    -4.4             
26                    -4.4             
27                    -4.3             
28                    -4.3             
29                    -4.2             
30                    -4.2             
31                    -4.1             
32                    -4.1             
33                    -4.0             

The following sample is an output of show olc link-tuner detail command.

RP/0/RP0/CPU0:ios#show olc link-tuner detail
Controller          : Ots0/0/0/0
Link Tuner Status   : OPERATIONAL
Last PSD computation: 2022-05-06 10:59:51
Computed Total Noise: -35.4 dB
----------------------------------------------------------------------
Setpoint            : Computed PSD
                     (dBm/12.5 GHz)
----------------------------------------------------------------------
01                    -5.7             
02                    -5.6             
03                    -5.6             
04                    -5.5             
05                    -5.5             
06                    -5.4             
07                    -5.4             
08                    -5.3             
09                    -5.3             
10                    -5.2             
11                    -5.2             
12                    -5.1             
13                    -5.1             
14                    -5.0             
15                    -5.0             
16                    -4.9             
17                    -4.9             
18                    -4.8             
19                    -4.8             
20                    -4.7             
21                    -4.7             
22                    -4.6             
23                    -4.6             
24                    -4.5             
25                    -4.4             
26                    -4.4             
27                    -4.3             
28                    -4.3             
29                    -4.2             
30                    -4.2             
31                    -4.1             
32                    -4.1             
33                    -4.0         

show olc otdr-status

Use the show olc otdr-status command to display the status of OTDR scan.

show olc otdr-status [ details ]

Syntax Description

details

Displays detailed OTDR scan status information.

Command Modes

Controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following samples display the various status of OTDR automatic scan during span fault:

RP/0/RP0/CPU0:ios#show olc otdr-status details
Mon Sep 18 13:16:16.461 UTC
Controller                                    : Ots0/0/0/0
Auto-scan Start Time                          : NA
OTDR Auto-scan Status                         : RUNNING
Status Detail                                 : Starting on Span Down
Optical Span Status                           : Down
Trigger Event                                 : Span Fault
Last Trigger Event                            : Span Restore

RP/0/RP0/CPU0:ios#show olc otdr-status details
Mon Sep 18 13:16:33.304 UTC
Controller                                    : Ots0/0/0/0
Auto-scan Start Time                          : 2023-09-18 13:16:27
OTDR Auto-scan Status                         : RUNNING
Status Detail                                 : Waiting Scan Completion on Span Down
Optical Span Status                           : Down
Trigger Event                                 : Span Fault
Last Trigger Event                            : Span Restore

RP/0/RP0/CPU0:ios#show olc otdr-status details
Mon Sep 18 13:18:54.154 UTC
Controller                                    : Ots0/0/0/0
Auto-scan Start Time                          : 2023-09-18 13:16:27
OTDR Auto-scan Status                         : COMPLETED
Status Detail                                 : Completed on Span Down
Optical Span Status                           : Down
Trigger Event                                 : Span Fault
Last Trigger Event                            : Span Fault

show olc raman-tuning

To view the Raman tuning status using show olc raman-tuning command.

show olc raman-tuning { controller Ots | | R/S/I/P }

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

controller Ots

Use this parameter to view the information for a particular controller.

Command Modes

User EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following sample is an output of the show olc raman-tuning command.

RP/0/RP0/CPU0:ios#sh olc raman-tuning 
Fri Apr  1 06:38:34.330 UTC

Controller                       : Ots0/0/0/0
Raman-Tuning Status              : TUNED
Tuning Complete Timestamp        : 2022-04-01 05:49:30.407029
Estimated Max Possible Gain      : 21.7 dB
Raman Gain Target                : 14.7 dB
Gain Achieved on Tuning Complete : 14.6 dB

The following sample is an output of the show olc raman-tuning controller ots r/s/i/p command.

RP/0/RP0/CPU0:ios#sh olc raman-tuning controller ots 0/0/0/0
Fri Apr  1 06:42:49.538 UTC

Controller                       : Ots0/0/0/0
Raman-Tuning Status              : TUNED
Tuning Complete Timestamp        : 2022-04-01 05:50:19.934044
Estimated Max Possible Gain      : 21.1 dB
Raman Gain Target                : 18.0 dB
Gain Achieved on Tuning Complete : 18.1 dB

show olc span-loss

Use the show olc span-loss command to view the Tx span loss and Rx span loss.

show olc span-loss { controller Ots | | R/S/I/P }

Syntax Description

R/S/I/P

Rack/Slot/Instance/Port of the OSC controller.

controller Ots

Use this parameter to view the span loss for a particular controller.

Command Modes

User EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following sample shows the output of the show olc span-loss command on a Raman span with Raman tuning enabled.

RP/0/RP0/CPU0:ios#show olc span-loss
Mon Apr 11 09:33:00.398 UTC

Controller name                           : Ots0/0/0/0
Neighbour RID                             : 10.1.1.2
Apparent Rx Span Loss                     : 7.7 dB
Rx Span Loss (with pumps off)             : 23.2 dB
Rx Span Loss (with pumps off) measured at : 2022-04-11 07:42:26
Estimated Rx Span Loss                    : 23.5 dB
Apparent Tx Span Loss                     : 17.5 dB
Tx Span Loss (with pumps off)             : 33.3 dB
Tx Span Loss (with pumps off) measured at : 2022-04-11 07:42:56
Estimated Tx Span Loss                    : 33.5 dB

show platform

To display information and status for each node in the network, use the show platform command in the XR EXEC mode.

Node Status and Information Command

Show platform

Chassis Door Status Command

show platform chassis-door

Syntax Description

show platform

Displays the status of the node

show platform chassis-door

Displays the status of the chassis front door.

Command Default

None

Command Modes

XR EXEC mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Cisco IOS XR Release 24.3.1

This show platform chassis-door command was introduced.

Usage Guidelines

None

Examples

To view the information of the node, use the following command:

RP/0/RP0/CPU0:ios#show platform

Mon May  6 16:38:13.609 IST

Node              Type                     State                    Config state

--------------------------------------------------------------------------------

0/RP0/CPU0        NCS1010-CTR2-B-K9(Active) IOS XR RUN               NSHUT,NMON

0/FT0             NCS1010-FAN              OPERATIONAL              NSHUT,NMON

0/FT1             NCS1010-FAN              OPERATIONAL              NSHUT,NMON

0/FT4             NCS1020-FAN              OPERATIONAL              NSHUT,NMON

0/FT5             NCS1020-FAN              OPERATIONAL              NSHUT,NMON

0/FT6             NCS1020-FAN              OPERATIONAL              NSHUT,NMON

0/FT7             NCS1020-FAN              OPERATIONAL              NSHUT,NMON

0/0/NXR0          NCS1K-E-OLT-C            OPERATIONAL              NSHUT,NMON

0/1/NXR0          NCS1010-FLR-P            PRESENT                  NSHUT,NMON

0/2/NXR0          NCS1K14-CCMD-16-C        OPERATIONAL              NSHUT,NMON

0/3/NXR0          NCS1K14-CCMD-16-C        OPERATIONAL              NSHUT,NMON

0/4/NXR0          NCS1K14-BLANK            PRESENT                  NSHUT,NMON

0/5/NXR0          NCS1K14-BLANK            PRESENT                  NSHUT,NMON

0/6/NXR0          NCS1K14-BLANK            PRESENT                  NSHUT,NMON

0/7/NXR0          NCS1K14-BLANK            PRESENT                  NSHUT,NMON

0/8/NXR0          NCS1K14-BLANK            PRESENT                  NSHUT,NMON

0/9/NXR0          NCS1K14-BLANK            PRESENT                  NSHUT,NMON

0/PM0             NCS1K4-AC-PSU-2          OPERATIONAL              NSHUT,NMON

0/PM1             NCS1K4-AC-PSU-2          OPERATIONAL              NSHUT,NMON

To view the status of the chassis door, use the following command:

RP/0/RP0/CPU0:ios#show platform chassis-door
Mon Jul  1 05:54:59.600 UTC
Chassis door present: Yes

Note


When there is no door installed on the chassis, the Chassis door present status shows No.


show version

To display the software version and details such as system uptime, use the show version command.

show version

Syntax Description

This command has no keywords or arguments.

Command Default

The software version and details such as system uptime are displayed for all the nodes in the system.

Command Modes

Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

Enter the show version command to display the software version, build information and system uptime.

Examples

The following example shows a sample output from the show version command.

sysadmin-vm:0_RP0# show version
RP/0/RP0/CPU0:ios#show version

Mon May  6 16:38:47.424 IST

Cisco IOS XR Software, Version 24.2.1.32I LNT

Copyright (c) 2013-2024 by Cisco Systems, Inc.

 

Build Information:

Built By     : cisco

Built On     : Thu Apr 11 02:06:44 UTC 2024

Build Host   : iox-ucs-033

Workspace    : /auto/iox-ucs-033-san1/prod/24.2.1.32I.SIT_IMAGE/ncs1010/ws/

Version      : 24.2.1.32I

Label        : 24.2.1.32I-MSFT_PILOT

 

cisco NCS1010 (C3758R @ 2.40GHz)

cisco NCS1020-SA (C3758R @ 2.40GHz) processor with 32GB of memory

NCS1020_P1B_DT_10 uptime is 4 days, 5 hours, 9 minutes

NCS 1020 Chassis

 

span-length

To configure span length, use the span-length command.

span-length length

Syntax Description

length

Span length in 0.1 km. Range: 1-2000

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example is a sample configuration that configures span-length to 10 km.

RP/0/RP0/CPU0:ios#configure
RP/0/RP0/CPU0:ios(config)#optical-line-control 
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#span-length 100
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

span-loss

To configure the span loss thresholds, use the span-loss command.

span-loss min | max threshold

Syntax Description

max

Maximum threshold

min

Minimum threshold

threshold

Threshold in range 0.0 to 42.0 dB in increments of 0.1 dB.

Command Modes

(config-olc-ots)

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following configuration example sets the span loss minimum threshold to 14 dB and maximum threshold to 35 dB.

RP/0/RP0/CPU0:ios#conf
RP/0/RP0/CPU0:ios(config)#optical-line-control
RP/0/RP0/CPU0:ios(config-olc)#controller ots 0/0/0/0
RP/0/RP0/CPU0:ios(config-olc-ots)#span-loss max 350
RP/0/RP0/CPU0:ios(config-olc-ots)#span-loss min 140
RP/0/RP0/CPU0:ios(config-olc-ots)#commit
RP/0/RP0/CPU0:ios(config-olc-ots)#end

tone-pattern controller

Use the tone-pattern controller command to start or stop initiating the tone pattern from the OTS controller.

tone-pattern controller ots R/S/I/P [ start | stop ]

Syntax Description

tone-pattern controller ots

Use this parameter to stop or start the tone pattern operation in the OTS controller.

R/S/I/P

Rack/Slot/Instance/Port of the OTS controller.

start

Use this parameter to start the tone-pattern operation in the OTS controller.

stop

Use this parameter to stop the tone-pattern operation in the OTS controller.

Command Default

None

Command Modes

controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

The following is a sample configuration of the tone-pattern controller ots command that starts the tone pattern on port 2 OTS controller.

RP/0/RP0/CPU0:ios#tone-pattern controller ots 0/0/0/4 start
Wed May 25 12:00:03.271 UTC
Tone pattern started

The following is a sample configuration of the tone-pattern controller ots command that stops the tone pattern on port 2 OTS controller.

RP/0/RP0/CPU0:ios#tone-pattern controller ots 0/0/0/4 stop
Wed May 25 12:00:03.271 UTC
Tone pattern detect started

tone-pattern-detect controller

Use the tone-pattern-detect controller command to start or stop detecting the tone pattern that is initiated from the OTS controller.

tone-pattern-detect controller controllertype R/S/I/P [ start | stop ]

Syntax Description

tone-pattern-detect controller

Use this parameter to stop or start the tone-pattern detect operation in a particular controller.

controllertype R/S/I/P

Rack/Slot/Instance/Port of the controller.

start

Use this parameter to start the tone-pattern detect operation in a particular controller.

stop

Use this parameter to stop the tone-pattern detect operation in a particular controller.

Command Default

None

Command Modes

controller configuration mode

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

The following is a sample configuration of the tone-pattern-detect controller command that starts the tone pattern detection on the OTS controller.

RP/0/RP0/CPU0:ios#tone-pattern-detect controller ots 0/0/0/4 start
Wed May 25 12:00:03.271 UTC
Tone pattern detect started

The following is a sample configuration of the tone-pattern-detect controller command that starts the tone pattern detection on the OMS controller.

RP/0/RP0/CPU0:ios#tone-pattern-detect controller oms 0/2/0/0 start
Wed May 25 12:00:03.271 UTC
Tone pattern detect started

The following is a sample configuration of the tone-pattern-detect controller command that stops the tone pattern detection on the OTS controller.

RP/0/RP0/CPU0:ios#tone-pattern-detect controller ots 0/0/0/4 stop
Wed May 25 12:00:03.271 UTC
Tone pattern detect started

The following is a sample configuration of the tone-pattern-detect controller command that stops the tone pattern detection on the OMS controller.

RP/0/RP0/CPU0:ios#tone-pattern-detect controller oms 0/2/0/0 stop
Wed May 25 12:00:03.271 UTC
Tone pattern detect started

upgrade hw-module

To upgrade a specific FPD, all the FPDs, or the FPDs belonging to a specific location, use the upgrade-hw-module command in Cisco IOS XR mode.

upgrade hw-module [location [ location-id | all]] [fpd [ fpd-name ] | all]

Syntax Description

location [location-id | all]

Upgrades the FPDs belonging to a specific location.

fpd [fpd-name | all]

Upgrades a specific FPD or all the FPDs.

Command Default

None

Command Modes

Cisco IOS XR

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Examples

The following example shows how to upgrade IoFpga FPD.

RP/0/RP0/CPU0:ios# upgrade hw-module location 0/Rack fpd IoFpga                                                                                                                     
 

ztp clean

To remove all Zero Touch Provisioning (ZTP) logs and settings that are saved on the node, use the ztp clean command in EXEC mode.

ztp clean

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Cisco IOS XR Configuration

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Example

None

To remove all the ZTP logs and saved settings use the following command.

RP/0/RP0/CPU0:ios#ztp clean
Fri Apr 29 06:49:29.760 UTC
This would remove all ZTP temporary files.
Would you like to proceed? [no]: yes
All ZTP operation files have been removed.
ZTP logs are present in /var/log/ztp*.log for logrotate.
Please remove manually if needed.
If you now wish ZTP to run again from boot, do 'conf t/commit replace' followed by reload.

ztp initiate

To remove all Zero Touch Provisioning (ZTP) logs and settings that are saved on the node, use the ztp clean command in EXEC mode.

ztp clean

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Cisco IOS XR Configuration

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

To initiate the ZTP use the following command.

RP/0/RP0/CPU0:ios#ztp initiate
Fri Jun 17 11:44:08.791 UTC
Initiating ZTP may change your configuration.
Interfaces might be brought up if they are in shutdown state
Would you like to proceed? [no]: yes
ZTP will now run in the background.
Please use "show logging" or look at /var/log/ztp.log to check progress.
RP/0/RP0/CPU0:ios#

ztp terminate

To terminate all existing Zero Touch Provisioning (ZTP) processes, use the ztp terminate command in EXECmode.

ztp terminate

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Cisco IOS XR Configuration

Command History

Release Modification
Cisco IOS XR Release 24.2.11

This command was introduced.

Usage Guidelines

None

Examples

To terminate the ZTP process use the following command.

RP/0/RP0/CPU0:ios#ztp terminate
Fri Apr 29 06:38:59.238 UTC
This would terminate active ZTP session if any (this may leave your system in a partially configured
state)
Would you like to proceed? [no]: yes
Terminating ZTP
No ZTP process running