Configuring STP and RSTP


This chapter applies to the ML-Series (ML100T-2, ML100X-8, and ML1000-2) cards and describes the IEEE 802.1D Spanning Tree Protocol (STP) and the ML-Series implementation of the IEEE 802.1W Rapid Spanning Tree Protocol (RSTP). It also explains how to configure STP and RSTP on the ML-Series card.

This chapter consists of these sections:

STP Features

RSTP

Interoperability with IEEE 802.1D STP

Configuring STP and RSTP Features

Verifying and Monitoring STP and RSTP Status

STP Features

These sections describe how the spanning-tree features work:

STP Overview

Supported STP Instances

Bridge Protocol Data Units

Election of the Root Switch

Bridge ID, Switch Priority, and Extended System ID

Spanning-Tree Timers

Creating the Spanning-Tree Topology

Spanning-Tree Interface States

Spanning-Tree Address Management

STP and IEEE 802.1Q Trunks

Spanning Tree and Redundant Connectivity

Accelerated Aging to Retain Connectivity

STP Overview

STP is a Layer 2 link management protocol that provides path redundancy while preventing loops in the network. For a Layer 2 Ethernet network to function properly, only one active path can exist between any two stations. Spanning-tree operation is transparent to end stations, which cannot detect whether they are connected to a single LAN segment or a switched LAN of multiple segments.

When you create fault-tolerant internetworks, you must have a loop-free path between all nodes in a network. The spanning-tree algorithm calculates the best loop-free path throughout a switched Layer 2 network. Switches send and receive spanning-tree frames, called bridge protocol data units (BPDUs), at regular intervals. The switches do not forward these frames, but use the frames to construct a loop-free path.

Multiple active paths among end stations cause loops in the network. If a loop exists in the network, end stations might receive duplicate messages. Switches might also learn end-station MAC addresses on multiple Layer 2 interfaces. These conditions result in an unstable network.

Spanning tree defines a tree with a root switch and a loop-free path from the root to all switches in the Layer 2 network. Spanning tree forces redundant data paths into a standby (blocked) state. If a network segment in the spanning tree fails and a redundant path exists, the spanning-tree algorithm recalculates the spanning-tree topology and activates the standby path.

When two interfaces on a switch are part of a loop, the spanning-tree port priority and path cost settings determine which interface is put in the forwarding state and which is put in the blocking state. The port priority value represents the location of an interface in the network topology and how well it is located to pass traffic. The path cost value represents media speed.

Supported STP Instances

The ML-Series card supports the per-VLAN spanning tree (PVST+) and a maximum of 255 spanning-tree instances.

Bridge Protocol Data Units

The stable, active, spanning-tree topology of a switched network is determined by these elements:

Unique bridge ID (switch priority and MAC address) associated with each VLAN on each switch

Spanning-tree path cost to the root switch

Port identifier (port priority and MAC address) associated with each Layer 2 interface

When the switches in a network are powered up, each functions as the root switch. Each switch sends a configuration BPDU through all of its ports. The BPDUs communicate and compute the spanning-tree topology. Each configuration BPDU contains this information:

Unique bridge ID of the switch that the sending switch identifies as the root switch

Spanning-tree path cost to the root

Bridge ID of the sending switch

Message age

Identifier of the sending interface

Values for the hello, forward delay, and max-age protocol timers

When a switch receives a configuration BPDU that contains superior information (lower bridge ID, lower path cost, etc.), it stores the information for that port. If this BPDU is received on the root port of the switch, the switch also forwards it with an updated message to all attached LANs for which it is the designated switch.

If a switch receives a configuration BPDU that contains inferior information to that currently stored for that port, it discards the BPDU. If the switch is a designated switch for the LAN from which the inferior BPDU was received, it sends that LAN a BPDU containing the up-to-date information stored for that port. In this way, inferior information is discarded, and superior information is propagated on the network.

A BPDU exchange results in these actions:

One switch in the network is elected as the root switch.

A root port is selected for each switch (except the root switch). This port provides the best path (lowest cost) when the switch forwards packets to the root switch.

The shortest distance to the root switch is calculated for each switch based on the path cost.

A designated switch for each LAN segment is selected. The designated switch incurs the lowest path cost when forwarding packets from that LAN to the root switch. The port through which the designated switch is attached to the LAN is called the designated port.

Interfaces included in the spanning-tree instance are selected. Root ports and designated ports are put in the forwarding state.

All interfaces not included in the spanning tree are blocked.

Election of the Root Switch

All switches in the Layer 2 network participating in the spanning tree gather information about other switches in the network through an exchange of BPDU data messages. This exchange of messages results in these actions:

Election of a unique root switch for each spanning-tree instance

Election of a designated switch for every switched LAN segment

Removal of loops in the switched network by blocking Layer 2 interfaces connected to redundant links

For each VLAN, the switch with the highest switch priority (the lowest numerical priority value) is elected as the root switch. If all switches are configured with the default priority (32768), the switch with the lowest MAC address in the VLAN becomes the root switch. The switch priority value occupies the most significant bits of the bridge ID.

When you change the switch priority value, you change the probability that the switch will be elected as the root switch. Configuring a higher value decreases the probability; a lower value increases the probability.

The root switch is the logical center of the spanning-tree topology in a switched network. All paths that are not needed to reach the root switch from anywhere in the switched network are placed in the spanning-tree blocking mode.

BPDUs contain information about the sending switch and its ports, including switch and MAC addresses, switch priority, port priority, and path cost. Spanning tree uses this information to elect the root switch and root port for the switched network and the root port and designated port for each switched segment.

Bridge ID, Switch Priority, and Extended System ID

The IEEE 802.1D standard requires that each switch has an unique bridge identifier (bridge ID), which determines the selection of the root switch. Because each VLAN is considered as a different logical bridge with PVST+, the same switch must have as many different bridge IDs as VLANs configured on it. Each VLAN on the switch has a unique 8-byte bridge ID; the two most-significant bytes are used for the switch priority, and the remaining six bytes are derived from the switch MAC address.

The ML-Series card supports the IEEE 802.1T spanning-tree extensions, and some of the bits previously used for the switch priority are now used as the bridge ID. The result is that fewer MAC addresses are reserved for the switch, and a larger range of VLAN IDs can be supported, all while maintaining the uniqueness of the bridge ID. As shown in Table 11-1, the two bytes previously used for the switch priority are reallocated into a 4-bit priority value and a 12-bit extended system ID value equal to the bridge ID. In earlier releases, the switch priority is a 16-bit value.

Table 11-1 Switch Priority Value and Extended System ID

Switch Priority Value
Extended System ID (Set Equal to the Bridge ID)
Bit 16
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1

32768

16384

8192

4096

2048

1024

512

256

128

64

32

16

8

4

2

1


Spanning tree uses the extended system ID, the switch priority, and the allocated spanning-tree MAC address to make the bridge ID unique for each VLAN. With earlier releases, spanning tree used one MAC address per VLAN to make the bridge ID unique for each VLAN.

Spanning-Tree Timers

Table 11-2 describes the timers that affect the entire spanning-tree performance.

Table 11-2 Spanning-Tree Timers 

Variable
Description

Hello timer

When this timer expires, the interface sends out a Hello message to the neighboring nodes.

Forward-delay timer

Determines how long each of the listening and learning states last before the interface begins forwarding.

Maximum-age timer

Determines the amount of time the switch stores protocol information received on an interface.


Creating the Spanning-Tree Topology

In Figure 11-1, Switch A is elected as the root switch because the switch priority of all the switches is set to the default (32768) and Switch A has the lowest MAC address. However, because of traffic patterns, number of forwarding interfaces, or link types, Switch A might not be the ideal root switch. By increasing the priority (lowering the numerical value) of the ideal switch so that it becomes the root switch, you force a spanning-tree recalculation to form a new topology with the ideal switch as the root.

Figure 11-1 Spanning-Tree Topology

When the spanning-tree topology is calculated based on default parameters, the path between source and destination end stations in a switched network might not be ideal. For instance, connecting higher-speed links to an interface that has a higher number than the root port can cause a root-port change. The goal is to make the fastest link the root port.

Spanning-Tree Interface States

Propagation delays can occur when protocol information passes through a switched LAN. As a result, topology changes can take place at different times and at different places in a switched network. When an interface transitions directly from nonparticipation in the spanning-tree topology to the forwarding state, it can create temporary data loops. Interfaces must wait for new topology information to propagate through the switched LAN before starting to forward frames. They must allow the frame lifetime to expire for forwarded frames that have used the old topology.

Each Layer 2 interface on a switch using spanning tree exists in one of these states:

Blocking—The interface does not participate in frame forwarding.

Listening—The first transitional state after the blocking state when the spanning tree determines that the interface should participate in frame forwarding.

Learning—The interface prepares to participate in frame forwarding.

Forwarding—The interface forwards frames.

Disabled—The interface is not participating in spanning tree because of a shutdown port, no link on the port, or no spanning-tree instance running on the port.

An interface moves through these states:

1. From initialization to blocking

2. From blocking to listening or to disabled

3. From listening to learning or to disabled

4. From learning to forwarding or to disabled

5. From forwarding to disabled

Figure 11-2 illustrates how an interface moves through the states.

Figure 11-2 Spanning-Tree Interface States

When you power up the switch, STP is enabled by default, and every interface in the switch, VLAN, or network goes through the blocking state and the transitory states of listening and learning. Spanning tree stabilizes each interface at the forwarding or blocking state.

When the spanning-tree algorithm places a Layer 2 interface in the forwarding state, this process occurs:

1. The interface is in the listening state while spanning tree waits for protocol information to transition the interface to the blocking state.

2. While spanning tree waits for the forward-delay timer to expire, it moves the interface to the learning state and resets the forward-delay timer.

3. In the learning state, the interface continues to block frame forwarding as the switch learns end-station location information for the forwarding database.

4. When the forward-delay timer expires, spanning tree moves the interface to the forwarding state, where both learning and frame forwarding are enabled.

Blocking State

A Layer 2 interface in the blocking state does not participate in frame forwarding. After initialization, a BPDU is sent to each interface in the switch. A switch initially functions as the root until it exchanges BPDUs with other switches. This exchange establishes which switch in the network is the root or root switch. If there is only one switch in the network, no exchange occurs, the forward-delay timer expires, and the interfaces move to the listening state. An interface always enters the blocking state after switch initialization.

An interface in the blocking state performs as follows:

Discards frames received on the port

Discards frames switched from another interface for forwarding

Does not learn addresses

Receives BPDUs

Listening State

The listening state is the first state a Layer 2 interface enters after the blocking state. The interface enters this state when the spanning tree determines that the interface should participate in frame forwarding.

An interface in the listening state performs as follows:

Discards frames received on the port

Discards frames switched from another interface for forwarding

Does not learn addresses

Receives BPDUs

Learning State

A Layer 2 interface in the learning state prepares to participate in frame forwarding. The interface enters the learning state from the listening state.

An interface in the learning state performs as follows:

Discards frames received on the port

Discards frames switched from another interface for forwarding

Learns addresses

Receives BPDUs

Forwarding State

A Layer 2 interface in the forwarding state forwards frames. The interface enters the forwarding state from the learning state.

An interface in the forwarding state performs as follows:

Receives and forwards frames received on the port

Forwards frames switched from another port

Learns addresses

Receives BPDUs

Disabled State

A Layer 2 interface in the disabled state does not participate in frame forwarding or in the spanning tree. An interface in the disabled state is nonoperational.

A disabled interface performs as follows:

Forwards frames switched from another interface for forwarding

Learns addresses

Does not receive BPDUs

Spanning-Tree Address Management

IEEE 802.1D specifies 17 multicast addresses, ranging from 0x00180C2000000 to 0x0180C2000010, to be used by different bridge protocols. These addresses are static addresses that cannot be removed.

The ML-Series card switches supported BPDUs (0x0180C2000000 and 01000CCCCCCD) when they are being tunneled via the protocol tunneling feature.

STP and IEEE 802.1Q Trunks

When you connect a Cisco switch to a non-Cisco device through an IEEE 802.1Q trunk, the Cisco switch uses PVST+ to provide spanning-tree interoperability. PVST+ is automatically enabled on IEEE 802.1Q trunks after users assign a protocol to a bridge group. The external spanning-tree behavior on access ports and Inter-Switch Link (ISL) trunk ports is not affected by PVST+.

For more information on IEEE 802.1Q trunks, see Chapter 16 "Configuring VLANs."

Spanning Tree and Redundant Connectivity

You can create a redundant backbone with spanning tree by connecting two switch interfaces to another device or to two different devices. Spanning tree automatically disables one interface but enables it if the other one fails, as shown in Figure 11-3. If one link is high speed and the other is low speed, the low-speed link is always disabled. If the speeds are the same, the port priority and port ID are added together, and spanning tree disables the link with the lowest value.

Figure 11-3 Spanning Tree and Redundant Connectivity

You can also create redundant links between switches by using EtherChannel groups. For more information, see Chapter 12 "Configuring Link Aggregation."

Accelerated Aging to Retain Connectivity

The default for aging dynamic addresses is 5 minutes, which is the default setting of the bridge bridge-group-number aging-time global configuration command. However, a spanning-tree reconfiguration can cause many station locations to change. Because these stations could be unreachable for 5 minutes or more during a reconfiguration, the address-aging time is accelerated so that station addresses can be dropped from the address table and then relearned.

Because each VLAN is a separate spanning-tree instance, the switch accelerates aging on a per-VLAN basis. A spanning-tree reconfiguration on one VLAN can cause the dynamic addresses learned on that VLAN to be subject to accelerated aging. Dynamic addresses on other VLANs can be unaffected and remain subject to the aging interval entered for the switch.

RSTP

RSTP provides rapid convergence of the spanning tree. It improves the fault tolerance of the network because a failure in one instance (forwarding path) does not affect other instances (forwarding paths). The most common initial deployment of RSTP is in the backbone and distribution layers of a Layer 2 switched network; this deployment provides the highly available network required in a service-provider environment.

RSTP improves the operation of the spanning tree while maintaining backward compatibility with equipment that is based on the (original) IEEE 802.1D spanning tree.

RSTP takes advantage of point-to-point wiring and provides rapid convergence of the spanning tree. Reconfiguration of the spanning tree can occur in less than 2 second (in contrast to 50 seconds with the default settings in the IEEE 802.1D spanning tree), which is critical for networks carrying delay-sensitive traffic such as voice and video.

These sections describe how RSTP works:

Supported RSTP Instances

Port Roles and the Active Topology

Rapid Convergence

Synchronization of Port Roles

Bridge Protocol Data Unit Format and Processing

Topology Changes

Supported RSTP Instances

The ML Series cards support per-VLAN rapid spanning tree (PVRST) and a maximum of 255 rapid spanning-tree instances.

Port Roles and the Active Topology

The RSTP provides rapid convergence of the spanning tree by assigning port roles and by determining the active topology. The RSTP builds upon the IEEE 802.1D STP to select the switch with the highest switch priority (lowest numerical priority value) as the root switch as described in the "Election of the Root Switch" section. Then the RSTP assigns one of these port roles to individual ports:

Root port—Provides the best path (lowest cost) when the switch forwards packets to the root switch.

Designated port—Connects to the designated switch, which incurs the lowest path cost when forwarding packets from that LAN to the root switch. The port through which the designated switch is attached to the LAN is called the designated port.

Alternate port—Offers an alternate path toward the root switch to that provided by the current root port.

Backup port—Acts as a backup for the path provided by a designated port toward the leaves of the spanning tree. A backup port can exist only when two ports are connected together in a loopback by a point-to-point link or when a switch has two or more connections to a shared LAN segment.

Disabled port—Has no role within the operation of the spanning tree.

A port with the root or a designated port role is included in the active topology. A port with the alternate or backup port role is excluded from the active topology.

In a stable topology with consistent port roles throughout the network, the RSTP ensures that every root port and designated port immediately transition to the forwarding state while all alternate and backup ports are always in the discarding state (equivalent to blocking in IEEE 802.1D). The port state controls the operation of the forwarding and learning processes. Table 11-3 provides a comparison of IEEE 802.1D and RSTP port states.

Table 11-3 Port State Comparison 

Operational Status
STP Port State
RSTP Port State
Is Port Included in the
Active Topology?

Enabled

Blocking

Discarding

No

Enabled

Listening

Discarding

No

Enabled

Learning

Learning

Yes

Enabled

Forwarding

Forwarding

Yes

Disabled

Disabled

Discarding

No



Caution STP edge ports are bridge ports that do not need STP enabled, where loop protection is not needed out of that port or an STP neighbor does not exist out of that port. For RSTP, it is important to disable STP on edge ports, which are typically front-side Ethernet ports, using the command bridge bridge-group-number spanning-disabled on the appropriate interface. If RSTP is not disabled on edge ports, convergence times will be excessive for packets traversing those ports.


Note To be consistent with Cisco STP implementations, Table 11-3 describes the port state as blocking instead of discarding. Designated ports start in the listening state.


Rapid Convergence

The RSTP provides for rapid recovery of connectivity following the failure of switch, a switch port, or a LAN. It provides rapid convergence for new root ports, and ports connected through point-to-point links as follows:

Root ports—If the RSTP selects a new root port, it blocks the old root port and immediately transitions the new root port to the forwarding state.

Point-to-point links—If you connect a port to another port through a point-to-point link and the local port becomes a designated port, it negotiates a rapid transition with the other port by using the proposal-agreement handshake to ensure a loop-free topology.

As shown in Figure 11-4, Switch A is connected to Switch B through a point-to-point link, and all of the ports are in the blocking state. Assume that the priority of Switch A is a smaller numerical value than the priority of Switch B. Switch A sends a proposal message (a configuration BPDU with the proposal flag set) to Switch B, proposing itself as the designated switch.

After receiving the proposal message, Switch B selects as its new root port the port from which the proposal message was received, forces all non edge ports to the blocking state, and sends an agreement message (a BPDU with the agreement flag set) through its new root port.

After receiving an agreement message from Switch B, Switch A also immediately transitions its designated port to the forwarding state. No loops in the network are formed because Switch B blocked all of its non edge ports and because there is a point-to-point link between Switches A and B.

When Switch C is connected to Switch B, a similar set of handshaking messages are exchanged. Switch C selects the port connected to Switch B as its root port, and both ends immediately transition to the forwarding state. With each iteration of this handshaking process, one more switch joins the active topology. As the network converges, this proposal-agreement handshaking progresses from the root toward the leaves of the spanning tree.

The switch determines the link type from the port duplex mode: a full-duplex port is considered to have a point-to-point connection; a half-duplex port is considered to have a shared connection.

Figure 11-4 Proposal and Agreement Handshaking for Rapid Convergence

Synchronization of Port Roles

When the switch receives a proposal message on one of its ports and that port is selected as the new root port, the RSTP forces all other ports to synchronize with the new root information. The switch is synchronized with superior root information received on the root port if all other ports are synchronized.

If a designated port is in the forwarding state, it transitions to the blocking state when the RSTP forces it to synchronize with new root information. In general, when the RSTP forces a port to synchronize with root information and the port does not satisfy any of the above conditions, its port state is set to blocking.

After ensuring all of the ports are synchronized, the switch sends an agreement message to the designated switch corresponding to its root port. When the switches connected by a point-to-point link are in agreement about their port roles, the RSTP immediately transitions the port states to forwarding. The sequence of events is shown in Figure 11-5.

Figure 11-5 Sequence of Events During Rapid Convergence

Bridge Protocol Data Unit Format and Processing

The RSTP BPDU format is the same as the IEEE 802.1D BPDU format except that the protocol version is set to 2. A new Length field is set to zero, which means that no version 1 protocol information is present. Table 11-4 shows the RSTP flag fields.

Table 11-4 RSTP BPDU Flags 

Bit
Function

0

Topology change (TC)

1

Proposal

2-3:

00

01

10

11

Port role:

Unknown

Alternate port

Root port

Designated port

4

Learning

5

Forwarding

6

Agreement

7

Topology change acknowledgement


The sending switch sets the proposal flag in the RSTP BPDU to propose itself as the designated switch on that LAN. The port role in the proposal message is always set to the designated port.

The sending switch sets the agreement flag in the RSTP BPDU to accept the previous proposal. The port role in the agreement message is always set to the root port.

The RSTP does not have a separate topology change notification (TCN) BPDU. It uses the topology change (TC) flag to show the topology changes. However, for interoperability with IEEE 802.1D switches, the RSTP switch processes and generates TCN BPDUs.

The learning and forwarding flags are set according to the state of the sending port.

Processing Superior BPDU Information

If a port receives superior root information (lower bridge ID, lower path cost, etc.) than currently stored for the port, the RSTP triggers a reconfiguration. If the port is proposed and is selected as the new root port, RSTP forces all the other ports to synchronize.

If the BPDU received is an RSTP BPDU with the proposal flag set, the switch sends an agreement message after all of the other ports are synchronized. If the BPDU is an IEEE 802.1D BPDU, the switch does not set the proposal flag and starts the forward-delay timer for the port. The new root port requires twice the forward-delay time to transition to the forwarding state.

If the superior information received on the port causes the port to become a backup or alternate port, RSTP sets the port to the blocking state but does not send the agreement message. The designated port continues sending BPDUs with the proposal flag set until the forward-delay timer expires, at which time the port transitions to the forwarding state.

Processing Inferior BPDU Information

If a designated port receives an inferior BPDU (higher bridge ID, higher path cost, etc.) than currently stored for the port with a designated port role, it immediately replies with its own information.

Topology Changes

This section describes the differences between the RSTP and the IEEE 802.1D in handling spanning-tree topology changes.

Detection—Unlike IEEE 802.1D in which any transition between the blocking and the forwarding state causes a topology change, only transitions from the blocking to the forwarding state cause a topology change with RSTP. (Only an increase in connectivity is considered a topology change.) State changes on an edge port do not cause a topology change. When an RSTP switch detects a topology change, it flushes the learned information on all of its non edge ports.

Notification—Unlike IEEE 802.1D, which uses TCN BPDUs, the RSTP does not use them. However, for IEEE 802.1D interoperability, an RSTP switch processes and generates TCN BPDUs.

Acknowledgement—When an RSTP switch receives a TCN message on a designated port from an IEEE 802.1D switch, it replies with an IEEE 802.1D configuration BPDU with the topology change acknowledgement bit set. However, if the TC-while timer (the same as the topology-change timer in IEEE 802.1D) is active on a root port connected to an IEEE 802.1D switch and a configuration BPDU with the topology change acknowledgement bit set is received, the TC-while timer is reset.

This behavior is only required to support IEEE 802.1D switches. The RSTP BPDUs never have the topology change acknowledgement bit set.

Propagation—When an RSTP switch receives a TC message from another switch through a designated or root port, it propagates the topology change to all of its non edge, edge, designated ports, and root port (excluding the port on which it is received). The switch starts the TC-while timer for all such ports and flushes the information learned on them.

Protocol migration—For backward compatibility with IEEE 802.1D switches, RSTP selectively sends IEEE 802.1D configuration BPDUs and TCN BPDUs on a per-port basis.

When a port is initialized, the timer is started (which specifies the minimum time during which RSTP BPDUs are sent), and RSTP BPDUs are sent. While this timer is active, the switch processes all BPDUs received on that port and ignores the protocol type.

If the switch receives an IEEE 802.1D BPDU after the port's migration-delay timer has expired, it assumes that it is connected to an IEEE 802.1D switch and starts using only IEEE 802.1D BPDUs. However, if the RSTP switch is using IEEE 802.1D BPDUs on a port and receives an RSTP BPDU after the timer has expired, it restarts the timer and starts using RSTP BPDUs on that port.

Interoperability with IEEE 802.1D STP

A switch running RSTP supports a built-in protocol migration mechanism that enables it to interoperate with legacy IEEE 802.1D switches. If this switch receives a legacy IEEE 802.1D configuration BPDU (a BPDU with the protocol version set to 0), it sends only IEEE 802.1D BPDUs on that port.

However, the switch does not automatically revert to the RSTP mode if it no longer receives IEEE 802.1D BPDUs because it cannot determine whether the legacy switch has been removed from the link unless the legacy switch is the designated switch. Also, a switch might continue to assign a boundary role to a port when the switch to which this switch is connected has joined the region.

Configuring STP and RSTP Features

These sections describe how to configure spanning-tree features:

Default STP and RSTP Configuration

Disabling STP and RSTP

Configuring the Root Switch

Configuring the Port Priority

Configuring the Path Cost

Configuring the Switch Priority of a Bridge Group

Configuring the Hello Time

Configuring the Forwarding-Delay Time for a Bridge Group

Configuring the Maximum-Aging Time for a Bridge Group

Default STP and RSTP Configuration

Table 11-5 shows the default STP and RSTP configuration.

Table 11-5 Default STP and RSTP Configuration 

Feature
Default Setting

Enable state

Up to 255 spanning-tree instances can be enabled.

Switch priority

32768 + Bridge ID

Spanning-tree port priority (configurable on a per-interface basis—used on interfaces configured as Layer 2 access ports)

128

Spanning-tree port cost (configurable on a per-interface basis)

1000 Mbps: 4

100 Mbps: 19

10 Mbps: 100

STS-1: 37

STS-3c: 14

STS-6c: 9

STS-9c: 7

STS-12c: 6

STS-24c: 3

Hello time

2 seconds

Forward-delay time

15 seconds

Maximum-aging time

20 seconds


Disabling STP and RSTP

STP is enabled by default on native VLAN 1 and on all newly created VLANs up to the specified spanning-tree limit of 255. Disable STP only if you are sure there are no loops in the network topology.


Caution STP edge ports are bridge ports that do not need STP enabled, where loop protection is not needed out of that port or an STP neighbor does not exist out of that port. For RSTP, it is important to disable STP on edge ports, which are typically front-side Ethernet ports, using the command bridge bridge-group-number spanning-disabled on the appropriate interface. If RSTP is not disabled on edge ports, convergence times will be excessive for packets traversing those ports.


Caution When STP is disabled and loops are present in the topology, excessive traffic and indefinite packet duplication can drastically reduce network performance.

Beginning in privileged EXEC mode, follow these steps to disable STP or RSTP on a per-VLAN basis:

 
Command
Purpose

Step 1 

Router# configure terminal

Enters the global configuration mode.

Step 2 

Router(config)# interface interface-id

Enters the interface configuration mode.

Step 3 

Router(config-if)# bridge-group 
bridge-group-number spanning disabled

Disables STP or RSTP on a per-interface basis.

Step 4 

Router(config-if)# end

Returns to privileged EXEC mode.

To reenable STP, use the no bridge-group bridge-group-number spanning disabled interface-level configuration command.

Configuring the Root Switch

The switch maintains a separate spanning-tree instance for each active VLAN configured on it. A bridge ID, consisting of the switch priority and the switch MAC address, is associated with each instance. For each VLAN, the switch with the lowest bridge ID becomes the root switch for that VLAN.


Note If your network consists of switches that both do and do not support the extended system ID, it is unlikely that the switch with the extended system ID support will become the root switch. The extended system ID increases the switch priority value every time the bridge ID is greater than the priority of the connected switches that are running older software.


Configuring the Port Priority

If a loop occurs, spanning tree uses the port priority when selecting an interface to put into the forwarding state. You can assign higher priority values (lower numerical values) to interfaces that you want selected first, and lower priority values (higher numerical values) that you want selected last. If all interfaces have the same priority value, spanning tree puts the interface with the lowest interface number in the forwarding state and blocks the other interfaces.

Beginning in privileged EXEC mode, follow these steps to configure the port priority of an interface:

 
Command
Purpose

Step 1 

Router# configure terminal

Enters the global configuration mode.

Step 2 

Router(config)# interface 
interface-id

Enters the interface configuration mode, and specifies an interface to configure.

Valid interfaces include physical interfaces and port-channel logical interfaces (port-channel port-channel-number).

Step 3 

Router(config-if)# bridge-group 
bridge-group-number priority-value

Configures the port priority for an interface that is an access port.

For the priority-value, the range is 0 to 255; the default is 128 in increments of 16. The lower the number, the higher the priority.

Step 4 

Router(config-if)# end

Return to privileged EXEC mode.

To return the interface to its default setting, use the no bridge-group id bridge-group-number priority- value command.

Configuring the Path Cost

The spanning-tree path cost default value is derived from the media speed of an interface. If a loop occurs, spanning tree uses cost when selecting an interface to put in the forwarding state. You can assign lower cost values to interfaces that you want selected first and higher cost values to interfaces that you want selected last. If all interfaces have the same cost value, spanning tree puts the interface with the lowest interface number in the forwarding state and blocks the other interfaces.

Beginning in privileged EXEC mode, follow these steps to configure the cost of an interface:

 
Command
Purpose

Step 1 

Router# configure terminal

Enters the global configuration mode.

Step 2 

Router(config)# interface 
interface-id

Enters the interface configuration mode and specifies an interface to configure.

Valid interfaces include physical interfaces and port-channel logical interfaces (port-channel port-channel-number).

Step 3 

Router(config-if)# bridge-group 
bridge-group-number path-cost 
cost

Configures the cost for an interface that is an access port.

If a loop occurs, spanning tree uses the path cost when selecting an interface to place into the forwarding state. A lower path cost represents higher-speed transmission.

For cost, the range is 0 to 65535; the default value is derived from the media speed of the interface.

Step 4 

Router(config-if)# end

Returns to the privileged EXEC mode.


Note The show spanning-tree interface interface-id privileged EXEC command displays information only for ports that are in a link-up operative state. Otherwise, you can use the show running-config privileged EXEC command to confirm the configuration.


To return the interface to its default setting, use the no bridge-group bridge-group-number path-cost cost command.

Configuring the Switch Priority of a Bridge Group

You can configure the switch priority and make it more likely that the switch will be chosen as the root switch.

Beginning in privileged EXEC mode, follow these steps to configure the switch priority of a bridge group:

 
Command
Purpose

Step 1 

Router# configure terminal

Enters the global configuration mode.

Step 2 

Router(config)# bridge 
bridge-group-number priority 
priority

Configures the switch priority of a bridge group.

For priority, the range is 0 to 61440 in increments of 4096; the default is 32768. The lower the number, the more likely the switch will be chosen as the root switch.

The value entered is rounded to the lower multiple of 4096. The actual number is computed by adding this number to the bridge group number.

Step 3 

Router(config)# end

Return to the privileged EXEC mode.

To return the switch to its default setting, use the no bridge bridge-group-number priority priority command.

Configuring the Hello Time

You can configure the interval between the generation of configuration messages by the root switch by changing the hello time.

Beginning in privileged EXEC mode, follow these steps to configure the hello time of a bridge group:

 
Command
Purpose

Step 1 

Router# configure terminal

Enters global configuration mode.

Step 2 

Router(config)# bridge 
bridge-group-number hello-time 
seconds

Configures the hello time of a bridge group. The hello time is the interval between the generation of configuration messages by the root switch. These messages mean that the switch is alive.

For seconds, the range is 1 to 10; the default is 2.

Step 3 

Router(config)# end

Returns to privileged EXEC mode.

To return the switch to its default setting, use the no bridge bridge-group-number hello-time seconds command.

Configuring the Forwarding-Delay Time for a Bridge Group

Beginning in privileged EXEC mode, follow these steps to configure the forwarding-delay time for a bridge group:

 
Command
Purpose

Step 1 

Router# configure terminal

Enters global configuration mode.

Step 2 

Router(config)# bridge 
bridge-group-number 
forward-time seconds

Configures the forward time of a VLAN. The forward delay is the number of seconds a port waits before changing from its spanning-tree learning and listening states to the forwarding state.

For seconds, the range is 4 to 200; the default is 15.

Step 3 

Router(config)# end

Returns to privileged EXEC mode.

To return the switch to its default setting, use the no bridge bridge-group-number forward-time seconds command.

Configuring the Maximum-Aging Time for a Bridge Group

Beginning in privileged EXEC mode, follow these steps to configure the maximum-aging time for a bridge group:

 
Command
Purpose

Step 1 

Router# configure terminal

Enters global configuration mode.

Step 2 

Router(config)# bridge 
bridge-group-number max-age 
seconds

Configures the maximum-aging time of a bridge group. The maximum-aging time is the number of seconds a switch waits without receiving spanning-tree configuration messages before attempting a reconfiguration.

For seconds, the range is 6 to 200; the default is 20.

Step 3 

Router(config)# end

Returns to privileged EXEC mode.

To return the switch to its default setting, use the no bridge bridge-group-number max-age seconds command.

Verifying and Monitoring STP and RSTP Status

To display the STP or RSTP status, use one or more of the privileged EXEC commands in Table 11-6.

Table 11-6 Commands for Displaying Spanning-Tree Status

 
Command
Purpose

Step 1 

ML_Series# show 
spanning-tree

Displays detailed STP or RSTP information.

Step 2 

ML_Series# show 
spanning-tree brief

Displays summary of STP or RSTP information.

Step 3 

ML_Series# show 
spanning-tree interface 
interface-id

Displays STP or RSTP information for the specified interface.

Step 4 

ML_Series# show 
spanning-tree summary 
[totals]

Displays a summary of port states or displays the total lines of the STP or RSTP state section.


Note The show spanning-tree interface interface-id privileged EXEC command displays information only if the port is in a link-up operative state. Otherwise, you can use the show running-config interface privileged EXEC command to confirm the configuration.


Examples of the show spanning-tree privileged EXEC command commands are shown here:

Example 11-1 show spanning-tree Commands

Router# show spanning-tree brief 
 
   
Bridge group 1
  Spanning tree enabled protocol ieee
  Root ID    Priority    32769
             Address     0005.9a39.6634
             This bridge is the root
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
 
   
  Bridge ID  Priority    32769  (priority 32768 sys-id-ext 1)
             Address     0005.9a39.6634
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
             Aging Time 300
 
   
Interface        Role Sts Cost      Prio.Nbr Type
---------------- ---- --- --------- -------- --------------------------------
Fa0              Desg FWD 19        128.3    P2p 
PO0              Desg FWD 3         128.20   P2p 
 
   
Router# show spanning-tree detail 
 
   
 Bridge group 1 is executing the ieee compatible Spanning Tree protocol
  Bridge Identifier has priority 32768, sysid 1, address 0005.9a39.6634
  Configured hello time 2, max age 20, forward delay 15
  We are the root of the spanning tree
  Topology change flag not set, detected flag not set
  Number of topology changes 2 last change occurred 00:16:45 ago
          from POS0
  Times:  hold 1, topology change 35, notification 2
          hello 2, max age 20, forward delay 15 
  Timers: hello 0, topology change 0, notification 0, aging 300
 
   
 Port 3 (FastEthernet0) of Bridge group 1 is forwarding 
   Port path cost 19, Port priority 128, Port Identifier 128.3.
   Designated root has priority 32769, address 0005.9a39.6634
   Designated bridge has priority 32769, address 0005.9a39.6634
   Designated port id is 128.3, designated path cost 0
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 1
   Link type is point-to-point by default
   BPDU: sent 641, received 0
 
   
 Port 20 (POS0) of Bridge group 1 is forwarding 
   Port path cost 3, Port priority 128, Port Identifier 128.20.
   Designated root has priority 32769, address 0005.9a39.6634
   Designated bridge has priority 32769, address 0005.9a39.6634
   Designated port id is 128.20, designated path cost 0
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 6
   Link type is point-to-point by default
   BPDU: sent 582, received 15
 
   
Router# show spanning-tree interface fast 0
 
   
Bridge Group     Role Sts Cost      Prio.Nbr Type
---------------- ---- --- --------- -------- --------------------------------
Bridge group 1   Desg FWD 19        128.3    P2p 
 
   
Router# show spanning-tree interface pos 0
 
   
Bridge Group     Role Sts Cost      Prio.Nbr Type
---------------- ---- --- --------- -------- --------------------------------
Bridge group 1   Desg FWD 3         128.20   P2p 
 
   
Router# show spanning-tree summary totals
Switch is in pvst mode
Root bridge for: Bridge group 1
 
   
Name                   Blocking Listening Learning Forwarding STP Active
---------------------- -------- --------- -------- ---------- ----------
1 bridge                     0         0        0          2          2