- About this Manual
- Chapter 1, Shelf Assembly Hardware
- Chapter 2, Common Control Cards
- Chapter 3, Optical Service Channel Cards
- Chapter 4, Optical Amplifier Cards
- Chapter 5, Multiplexer and Demultiplexer Cards
- Chapter 6, Optical Add/Drop Cards
- Chapter 7, Reconfigurable Optical Add/Drop Cards
- Chapter 8, Transponder and Muxponder Cards
- Chapter 9, Node Reference
- Chapter 10, Network Reference
- Chapter 11, Optical Channel Circuits and Virtual Patchcords Reference
- Chapter 12, Cisco Transport Controller Operation
- Chapter 13, Security Reference
- Chapter 14, Timing Reference
- Chapter 15, Manage Network Connectivity
- Chapter 16, Alarm and TCA Monitoring and Management
- Chapter 17, Performance Monitoring
- Chapter 18, SNMP
- Appendix A, Hardware Specifications
- Appendix B, Administrative and Service States
- Appendix C, Network Element Defaults
- A.1 Shelf Specifications
- A.1.1 Bandwidth
- A.1.2 Configurations
- A.1.3 Cisco Transport Controller
- A.1.4 External LAN Interface
- A.1.5 TL1 Craft Interface
- A.1.6 Modem Interface
- A.1.7 Alarm Interface
- A.1.8 EIA Interface (ANSI only)
- A.1.9 BITS Interface (ANSI only)
- A.1.10 System Timing
- A.1.11 System Power
- A.1.12 Fan Tray
- A.1.13 System Environmental Specifications
- A.1.14 Dimensions
- A.2 General Card Specifications
- A.3 Common Control Card Specifications
- A.4 Optical Service Channel Cards
- A.5 Optical Amplifier Cards
- A.6 Multiplexer and Demultiplexer Cards
- A.7 Reconfigurable Optical Add/Drop Cards
- A.7.1 32DMX Card Specifications
- A.7.2 32DMX-L Card Specifications
- A.7.3 32WSS Card Specifications
- A.7.4 32WSS-L Card Specifications
- A.7.5 40-MUX-C Card Specifications
- A.7.6 40-DMX-C Card Specifications
- A.7.7 40-WSS-C Card Specifications
- A.7.8 40-WXC-C Card Specifications
- A.7.9 MMU Card Specifications
- A.8 Optical Add/Drop Cards
- A.9 Transponder and Muxponder Card Specifications
- A.9.1 TXP_MR_10G Card Specifications
- A.9.2 MXP_2.5G_10G Card Specifications
- A.9.3 TXP_MR_2.5G and TXPP_MR_2.5G Card Specifications
- A.9.4 MXP_MR_2.5G and MXPP_MR_2.5G Card Specifications
- A.9.5 MXP_2.5G_10E Card Specifications
- A.9.6 MXP_2.5G_10E_C Card Specifications
- A.9.7 MXP_2.5G_10E_L Card Specifications
- A.9.8 MXP_MR_10DME_C Card Specifications
- A.9.9 MXP_MR_10DME_L Card Specifications
- A.9.10 TXP_MR_10E Card Specifications
- A.9.11 TXP_MR_10E_C Card Specifications
- A.9.12 TXP_MR_10E_L Card Specifications
- A.9.13 ADM-10G Card Specifications
- A.9.14 GE_XP and 10GE_XP Card Specifications
- A.10 Mesh Patch Panel Specifications
- A.11 SFP and XFP Specifications
Hardware Specifications
This appendix contains hardware and software specifications for the ONS 15454 ANSI and ETSI shelf assemblies and cards.
Note 
Unless otherwise specified, "ONS 15454" refers to both ANSI and ETSI shelf assemblies.
The following sections are included:
•Common Control Card Specifications
•Optical Service Channel Cards
•Multiplexer and Demultiplexer Cards
•Reconfigurable Optical Add/Drop Cards
•Transponder and Muxponder Card Specifications
•Mesh Patch Panel Specifications
A.1 Shelf Specifications
This section provides specifications for shelf bandwidth; a list of topologies; Cisco Transport Controller (CTC) specifications; the LAN, Transaction Language One (TL1), modem, and alarm specifications; timing, power, and environmental specifications; and shelf dimensions.
A.1.1 Bandwidth
The ONS 15454 has the following bandwidth specifications:
•Total bandwidth: 240 Gbps
•Data plane bandwidth: 160 Gbps
•SONET/SDH plane bandwidth: 80 Gbps
A.1.2 Configurations
The ONS 15454 can be configured for the following dense wavelength division multiplexing (DWDM) topologies:
•Hubbed rings
•Multihubbed rings
•Point-to-point
•Linear
•Linear with optical add/drop multiplexing (OADM)
•Hybrid terminal node
•Hybrid OADM node
•Hybrid line amplifier node
A.1.3 Cisco Transport Controller
CTC, the ONS 15454 craft interface software, has the following specifications:
•10BaseT Ethernet
•TCC2/TCC2P card access: RJ-45 connector
•Backplane access: LAN pin field (ANSI only)
•Front Mount Electrical Connection (FMEC) access: LAN connector on MIC-C/T/P faceplate (ETSI only)
A.1.4 External LAN Interface
The ONS 15454 external LAN interface has the following specifications:
•10BaseT Ethernet
•Backplane access: LAN pin field (ANSI only)
•FMEC access: LAN connector on MIC-C/T/P faceplate (ETSI only)
A.1.5 TL1 Craft Interface
The ONS 15454 TL1 craft interface has the following specifications:
•Speed: 9600 bps
•TCC2/TCC2P access: EIA/TIA-232 DB-9 type connector
•Backplane access: CRAFT pin field (ANSI only)
A.1.6 Modem Interface
The ONS 15454 modem interface has the following specifications:
•Hardware flow control
•TCC2/TCC2P: EIA/TIA-232 DB-9 type connector
A.1.7 Alarm Interface
The ONS 15454 alarm interface has the following specifications:
•ETSI
–Visual: Critical, Major, Minor, Remote
–Audible: Critical, Major, Minor, Remote
–FMEC access: 62-Pin DB connector on MIC-A/P faceplate
–Alarm inputs: Common 32-VDC output for all alarm-inputs, closed contact limited to 2 mA
–Control outputs: Open contact maximum 60 VDC, closed contact maximum 100 mA
•ANSI
–Visual: Critical, Major, Minor, Remote
–Audible: Critical, Major, Minor, Remote
–Backplane access: Alarm pin fields
–Alarm contacts: 0.045 mm, -48 V, 50 mA
A.1.8 EIA Interface (ANSI only)
The ONS 15454 electrical interface assembly (EIA) interface has the following specifications:
•SMB: AMP #415504-3 75-ohm, 4-leg connectors
•BNC: Trompeter #UCBJ224 75-ohm 4 leg connector (King or ITT are also compatible)
•AMP Champ: AMP#552246-1 with #552562-2 bail locks
A.1.9 BITS Interface (ANSI only)
The ONS 15454 building integrated timing supply (BITS) interface has the following specifications:
•2 DS-1 BITS inputs
•2 derived DS-1 outputs
•Backplane access: BITS pin field
A.1.10 System Timing
The ONS 15454 ANSI has the following system timing specifications:
•Stratum 3 per Telcordia GR-253-CORE
•Free running accuracy: +/- 4.6 ppm
•Holdover stability: 3.7 x 10-7 per day, including temperature (< 255 slips in first 24 hours)
•Reference: External BITS, line, internal
The ONS 15454 ETSI has the following system timing specifications:
•Stratum 3E, per ITU-T G.813
•Free running accuracy: +/- 4.6 ppm
•Holdover stability: 3.7 exp -7 per day, including temperature (< 255 slips in first 24 hours)
•Reference: External BITS, line, internal
A.1.11 System Power
The ONS 15454 ANSI has the following power specifications:
•Input power: -48 VDC
•Power consumption: Configuration dependent; 55 W (fan tray only)
•Power requirements: -40.5 to -57 VDC
•Power terminals: #6 Lug
•ANSI shelf: 100-A fuse panel (minimum 30 A fuse per shelf)
HD shelf: 100-A fuse panel (minimum 30 A fuse per shelf)
The ONS 15454 ETSI has the following power specifications:
•Input voltage: -48 VDC
•Power consumption: Configuration dependent; 53 W (fan tray only)
•Power requirements:
–Nominal: -48 VDC
–Tolerance limits: -40.5 to -57.0 VDC
•Power terminals: 3WK3 Combo-D power cable connector (MIC-A/P and MIC-C/T/P faceplates)
•Fusing: 100 A fuse panel; minimum 30 A fuse per shelf
A.1.12 Fan Tray
Table A-1 lists power requirements for the fan-tray assembly.
|
|
|
|
|
|---|---|---|---|
|
|
53 |
1.21 |
198 |
|
|
86.4 |
1.8 |
295 |
|
|
115 |
2.4 |
393 |
A.1.13 System Environmental Specifications
The ONS 15454 ANSI has the following environmental specifications:
•Operating temperature:
C-Temp: 32 to +131 degrees Farenheit (0 to +55 degrees Celsius)
I-Temp: -40 to +139 degrees Farenheit (-40 to +65 degrees Celsius)
•Operating humidity: 5 to 95 percent, noncondensing
The ONS 15454 ETSI has the following environmental specifications:
•Operating temperature: 32 to 104 degrees Fahrenheit (0 to +40 degrees Celsius)
•Operating humidity: 5 to 95 percent, noncondensing
A.1.14 Dimensions
The ONS 15454 ANSI shelf assembly has the following dimensions:
•Height: 18.5 in. (40.7 cm)
•Width: 19 or 23 in. (41.8 or 50.6 cm) with mounting ears attached
•Depth: 12 in. (26.4 cm) (5 in. or 12.7 cm projection from rack)
•Weight: 55 lb (24.947 kg) empty
The ONS 15454 ETSI shelf assembly has the following dimensions:
•Height: 616.5 mm (24.27 in.)
•Width: 535 mm (17 in.) without mounting ears attached
•Depth: 280 mm (11.02 in.)
•Weight: 26 kg empty (57.3 lb)
A.2 General Card Specifications
This section provides power specifications and temperature ranges for all ONS 15454 cards.
A.2.1 Power
Table A-2 provides power consumption information for the ONS 15454 cards.
A.2.2 Temperature
•Operating temperature:
–Long term: 0 to 40 degrees Celsius (32 to 104 degrees Fahrenheit)
–Short term: Functionality is guaranteed at -5 to 55 degrees Celsius (23 to 131 degrees Fahrenheit), according to GR-63 Issue 3
The indicated temperatures are the ambient ones in which the shelf can be placed.
A.3 Common Control Card Specifications
This section provides specifications for the TCC2, TCC2P, AIC, and AIC-I cards, the alarm expansion panel (AEP), the MIC-A/P and MIC-C/T/P FMECs, and the MS-ISC-100T card.
For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance Information document.
A.3.1 TCC2 Card Specifications
The TCC2 card has the following specifications:
•CTC software
–Interface: EIA/TIA-232 (local craft access, on TCC2 faceplate)
–Interface: 10BaseT LAN (on TCC2 faceplate)
–Interface: 10BaseT LAN (through the backplane)
•Synchronization
–Stratum 3, per Telcordia GR-253-CORE
–Free running access: Accuracy +/- 4.6 ppm
–Holdover stability: 3.7 x 10-7 per day including temperature (< 255 slips in first 24 hours)
–Reference: External BITS, line, internal
•Supply voltage monitoring
–Both supply voltage inputs are monitored.
–Normal operation: -40.5 to -56.7 V
–Undervoltage: Major alarm
–Overvoltage: Major alarm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 235 mm (9.250 in.)
–Weight not including clam shell: 0.7 kg (1.5 lb)
A.3.2 TCC2P Card Specifications
The TCC2P card has the following specifications:
•CTC software
–Interface: EIA/TIA-232 (local craft access, on TCC2P faceplate)
–Interface: 10BaseT LAN (on TCC2P faceplate)
–Interface: 10BaseT LAN (through the backplane)
•Synchronization
–Stratum 3, per Telcordia GR-253-CORE
–Free running access: Accuracy +/- 4.6 ppm
–Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)
–Reference: External BITS, line, internal
•Supply voltage monitoring
–Both supply voltage inputs are monitored.
–Normal operation: -40.5 to -56.7 V (in -48 VDC systems)
–Undervoltage: Major alarm
–Overvoltage: Major alarm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 1.5 lb (0.7 kg)
A.3.3 AIC-I Card Specifications
The AIC-I card has the following specifications:
•Alarm inputs
–Number of inputs: 12 without AEP, 32 with AEP
–Opto-coupler isolated
–Label customer provisionable
–Severity customer provisionable
–Common 32 V output for all alarm inputs
–Each input limited to 2 mA
–Termination: Wire-wrap on backplane without AEP, on AEP connectors with AEP
•Alarm outputs
–Number of outputs: 4 (user configurable as inputs) without AEP, 16 with AEP
–Switched by opto MOS (metal oxide semiconductor)
–Triggered by definable alarm condition
–Maximum allowed open circuit voltage: 60 VDC
–Maximum allowed closed circuit current: 100 mA
–Termination: Wire-wrap on backplane without AEP, on AEP connectors with AEP
•Express orderwire/local orderwire (EOW/LOW)
–ITU-T G.711, ITU-T G.712, Telcordia GR-253-CORE
–A-law, mu-law
Note Due to the nature of mixed coding, in a mixed-mode (A-law/mu-law) configuration, the orderwire is not ITU-T G.712 compliant.
–Orderwire party line
–Dual tone, multifrequency (DTMF) signaling
•User data channel (UDC)
–Bit rate: 64 kbps, codirectional
–ITU-T G.703
–Input/output impedance: 120 ohm
–Termination: RJ-11 connectors
•Data communications channel (DCC)
–Bit rate: 576 kbps
–EIA/TIA-485/V11
–Input/output impedance: 120 ohm
–Termination: RJ-45 connectors
•ACC connection for additional alarm interfaces
–Connection to AEP
•Power monitoring alarming states:
–Power failure (0 to -38 VDC)
–Undervoltage (-38 to -40.5 VDC)
–Overvoltage (beyond -56.7 VDC)
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Weight: 1.8 lb (0.82 kg)
A.3.4 AEP Specifications (ANSI only)
The AEP has the following specifications:
•Alarm inputs
–Number of inputs: 32
–Optocoupler isolated
–Label customer provisionable
–Severity customer provisionable
–Common 32 V output for all alarm inputs
–Each input limited to 2 mA
–Termination: 50-pin AMP champ connector
•Alarm outputs
–Number of outputs: 16
–Switched by opto MOS
–Triggered by definable alarm condition
–Maximum allowed open circuit voltage: 60 VDC
–Maximum allowed closed circuit current: 100 mA
–Termination: 50-pin AMP champ connector
•Environmental
–Overvoltage protection: as in ITU-T G.703 Annex B
•Dimensions of AEP board
–Height: 20 mm (0.79 in.)
–Width: 330 mm (13.0 in.)
–Depth: 89 mm (3.5 in.)
–Weight: 0.18 kg (0.4 lb)
A.3.5 MIC-A/P FMEC Specifications (ETSI only)
The MIC-A/P FMEC card has the following specifications:
•Power supply input BATTERY B
–System supply voltage: Nominal -48 VDC
Tolerance limits: -40.5 to -57.0 VDC
–Connector: 3WK3 Combo-D power cable connector
•Alarm outputs
–Voltage (open contact): Maximum 60 VDC
–Current (closed contact): Maximum 250 mA
–Connector: 62-pin DB connector (common for inputs/outputs)
•Alarm inputs
–Voltage (open contact): Maximum 60 VDC
–Current (closed contact): Maximum 2 mA
–Connector: 62-pin DB connector (common for inputs/outputs)
•Dimensions
–Height: 182 mm (7.165 in.)
–Width: 31.88 mm (1.255 in.)
–Depth: 92 mm (3.62 in.)
–Depth with backplane connector: 98 mm (3.87 in.)
–Weight not including clam shell: 0.2 kg (0.5 lb)
A.3.6 MIC-C/T/P FMEC Specifications (ETSI only)
The MIC-C/T/P FMEC card has the following specifications:
•Power supply input BATTERY A
–System supply voltage: Nominal -48 VDC
Tolerance limits: -40.5 to -57.0 VDC
–Connector: 3WK3 Combo-D power cable connector
•Timing connector
–Frequency: 2.048 MHz +/-10 ppm
–Signal level: 0.75 to 1.5 V
–Impedance: 75 ohms +/-5 percent (switchable by jumper to high impedance > 3 kohms)
Note 120 ohms balanced impedance is possible with external matching cable.
–Cable attenuation: Up to 6 dB at 2 MHz
–Connectors: 1.0/2.3 miniature coax connector
•System management serial port:
–System management serial port craft interface
–Modem port (for future use)
–Connectors: 8-pin RJ-45
•System management LAN port connectors:
–Signal: IEEE 802.3 10BaseT
–Connectors: 8-pin RJ-45
•Dimensions
–Height: 182 mm (7.165 in.)
–Width: 31.88 mm (1.255 in.)
–Depth: 92 mm (3.62 in.)
–Depth with backplane connector: 98 mm (3.87 in.)
–Weight not including clam shell: 0.2 kg (0.5 lb)
A.3.7 MS-ISC-100T Card Specifications
The MS-ISC-100T card has the following specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.3 lb (1.0 kg)
A.4 Optical Service Channel Cards
This section provides specifications for the OSCM and OSC-CSM cards.
A.4.1 OSCM Card Specifications
The OSCM card has the following specifications:
•Line
–Bit rate: 155 Mbps
–Code: Scrambled non-return to zero (NRZ)
–Loopback modes: None
–Connector: Duplex LC
•Transmitter optical service channel (OSC) signal
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -5 dBm
–Nominal wavelength: 1510-nm +/-10 nm
–Variable optical attenuator (VOA) necessary in the transmit path to adjust the in-fiber optical power level
•Receiver OSC signal
–Maximum receiver level: -8 dBm at 10-10 bit error rate (BER)
–Minimum receiver level: -40 dBm at 10-10 BER
–Span budget: 40-dB span budget (about 150 km assuming fiber path loss equals 0.25 dB/km)
–Jitter tolerance: Telcordia GR-253/G.823 compliant
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.4.2 OSC-CSM Card Specifications
The OSC-CSM card has the following specifications:
•Line
–Bit rate: 155 Mbps
–Code: Scrambled NRZ
–Loopback modes: None
–Connector: Duplex LC
•Transmitter OSC signal
–Maximum transmitter output power: -2 dBm
–Minimum transmitter output power: -24 dBm
–Nominal wavelength: 1510-nm +/-10 nm
–VOA is necessary in the transmit path to adjust the in-fiber optical power level
•Receiver OSC signal
–Maximum receiver level: -8 dBm at 10-10 BER
–Minimum receiver level: -40 dBm at 10-10 BER
–Span loss budget: 35-dB span budget (approximately 140 km assuming that the fiber path loss is equal to 0.25 dB/km)
–Jitter tolerance: Telcordia GR-253/G.823 compliant
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.5 Optical Amplifier Cards
This section provides specifications for the OPT-PRE amplifier, OPT-BST amplifier, OPT-BST-E amplifier, OPT-BST-L amplifier, OPT-AMP-L preamplifier (configurable as a preamplifier or booster amplifier), and OPT-AMP-17-C amplifier cards.
A.5.1 OPT-PRE Amplifier Card Specifications
The OPT-PRE amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1530 to 1561.3 nm
–Gain ripple (peak to valley): 1.5 dB
–Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 3 to 9 dB
–Gain range: 5 to 38.5 dBm in constant power mode, 5 to 28 dBm in constant gain mode
–Minimum gain (standard range): 5.0 dBm
– Maximum gain (standard range with programmable gain tilt): 21 dBm
– Maximum gain (extended range with uncontrolled gain tilt): 38.5 dBm
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 17.5 dBm
–Maximum output power (with full channel load): 17 dB
–Minimum output power (with one channel): -1 dBm
–Input power (Pin) range at full channel load: -21.5 to 12 dBm
–Input power (Pin) range at single channel load: -39.5 to -6 dBm
–Noise figure at G3 21 dB = 6.5 dB
–OSC filter drop (channels) insertion loss maximum: 1 dB
–OSC filter drop (OSC) insertion loss maximum: 1.8 dB
–OSC filter add (OSC) insertion loss maximum: 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.2 OPT-BST Amplifier Card Specifications
The OPT-BST amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1530 to 1561.3 nm
–Gain ripple (peak to valley): 1.5 dB
–Gain range: 5 to 20 dBm with programmable gain tilt
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 17.5 dBm
–Maximum output power (with full channel load): 17 dB
–Minimum output power (with one channel): -1 dBm
–Input power (Pin) range at full channel load: -3 to 12 dBm
–Input power (Pin) range at single channel load: -21 to -6 dBm
–Noise figure at G3 20 dB = 6 dB
–OSC filter drop (channels) insertion loss maximum: 1 dB
–OSC filter drop (OSC) insertion loss maximum: 1.8 dB
–OSC filter add (OSC) insertion loss maximum: 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.3 OPT-BST-E Amplifier Card Specifications
The OPT-BST-E amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1530 to 1561.3 nm
–Gain ripple (peak to valley): 1.8 dB
–Gain range: 8 to 23 dB with programmable gain tilt
–Extended gain range: 23 to 26 dB with gain tilt uncontrolled
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 20.5 dBm
–Maximum output power (with full channel load): 20 dB
–Minimum output power (with one channel): -0 dBm
–Input power (Pin) range at full channel load: -6 to 12 dBm
–Input power (Pin) range at single channel load: -26 to -8 dBm
–Noise figure at G3 23 dB = 6 dB
–OSC filter drop (channels) insertion loss maximum: 1 dB
–OSC filter drop (OSC) insertion loss maximum: 1.8 dB
–OSC filter add (OSC) insertion loss maximum: 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.4 OPT-BST-L Amplifier Card Specifications
The OPT-BST-L amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1570.0 to 1605.0 nm
–Gain ripple (peak to valley): 1.5 dB
–Gain range: 8 to 20 dB with programmable gain tilt
–Extended gain range: 20 to 27 dB with gain tilt uncontrolled
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 10 dBm
–Maximum output power (with full channel load): 17 dB
–Minimum output power (with one channel): -1 dBm
–Input power (Pin) range at full channel load: -10 to 9 dBm
–Input power (Pin) range at single channel load: -37 to -18 dBm
–Noise figure at G3 20 dB = 7.5 dB
–Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
–Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
–Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.5 OPT-AMP-L Preamplifier Card Specifications
The OPT-AMP-L card has the following specifications:
•Optical characteristics:
–DWDM channel wavelength plan, 100 GHz, 4 skip 1, ITU-T wavelength grid channels 71 (1602.3 nm) to 90 (1570.4 nm)
–DWDM channel wavelength plan, 50 GHz, 8 skip 2, ITU-T wavelength grid channels 70.5 (1602.7 nm) to 90 (1570.4 nm)
–Channel spacing: 100 and 50 GHz
–Total operating wavelength range 1570.0 - 1605.0 nm
–Gain ripple (peak to valley): 1.5 dB
–Standard gain range: 12 to 24 dB
–Extended gain range (uncontrolled gain tilt): 24 to 35 dB
–Gain and power regulation over/undershoot: 0.5 dB
–Minimum output power (with one channel): +2 dBm
–Maximum power output (standard or extended gain range): 20 dB
–Input power range (full channel load): -15 to 8 dB
–Input power range (single channel load): -40 to -17
–Noise figure at G3 20 dB = 8.9 dB
–Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
–Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
–Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.6 OPT-AMP-17-C Amplifier Card Specifications
The OPT-AMP-17-C card has the following specifications:
•Optical characteristics:
–DWDM channel wavelength plan: 80 channels at 50 GHz spacing, 1530.33 nm to 1561.83 nm
–Channel spacing: 50 GHz
–Total operating wavelength range 1529.0 to 1562.5 nm
–Gain ripple (peak to valley): 1.5 dB
–Gain range: 14 to 23 dB
–Optimal gain (gain tilt = 0): 17 dB
–Gain and power regulation over/undershoot: 0.5 dB
–Minimum output power (with one channel): -2 dBm
–Maximum power output (standard or extended gain range): 17.5 dBm
–Input power range (full channel load): -6 to 3 dBm
–Input power range (single channel load): -28 to -19 dBm
–Noise figure at G=17dB = 6 dB maximum
–Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
–Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
–Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.6 Multiplexer and Demultiplexer Cards
This section provides specifications for the 32MUX-O, 32DMX-O, and 4MD-xx.x cards.
A.6.1 32MUX-O Card Specifications
The 32MUX-O card optical specifications are listed in Table A-3.
Note For power specifications, see Table A-2.
The 32MUX-O card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.6.2 32DMX-O Card Specifications
The 32DMX-O card optical specifications are listed in Table A-4.
Note For power specifications, see Table A-2.
The 32DMX-O card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.6.3 4MD-xx.x Card Specifications
The 4MD-xx.x card optical specifications are listed in Table A-5.
Note For power specifications, see Table A-2.
The 4MD-xx.x card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7 Reconfigurable Optical Add/Drop Cards
This section provides specifications for the 32DMX, 32DMX-L, 40-MUX-C, 40-DMX-C, 40-WSS-C, 40-WXC-C, 32WSS, 32WSS-L, and MMU cards.
A.7.1 32DMX Card Specifications
The 32DMX card optical specifications are listed in Table A-6.
Note For power specifications, see Table A-2.
The 32DMX channel plan is shown in Table A-7. All 32DMX client interfaces must comply with this plan.
The 32DMX card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7.2 32DMX-L Card Specifications
The 32DMX-L card optical specifications are listed in Table A-6.
Note For power specifications, see Table A-2.
The 32DMX-L channel plan is shown in Table A-9. All 32DMX-L client interfaces must comply with this plan.
The 32DMX-L card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7.3 32WSS Card Specifications
The 32WSS card optical specifications are listed in Table A-10.
Note For power specifications, see Table A-2.
The 32WSS channel plan is shown in Table A-11. All 32WSS client interfaces must comply with this plan.
The 32WSS card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7.4 32WSS-L Card Specifications
The 32WSS-L card optical specifications are listed in Table A-12.
Note For power specifications, see Table A-2.
The 32WSS-L channel plan is shown in Table A-13. All 32WSS-L client interfaces must comply with this plan.
The 32WSS-L card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7.5 40-MUX-C Card Specifications
The 40-MUX-C card optical specifications are listed in Table A-14.
Note For power specifications, see Table A-2.
The 40-MUX-C card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7.6 40-DMX-C Card Specifications
The 40-DMX-C card optical specifications are listed in Table A-15.
Note For power specifications, see Table A-2.
The 40-DMX-C card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7.7 40-WSS-C Card Specifications
The 40-WSS-C card optical specifications are listed in Table A-16.
Note For power specifications, see Table A-2.
The 40-WSS-C card channel grid is listed in Table A-17.
The 40-WSS-C card has the following additional specifications:
•Dimensions
–Height: 8.66 in. (220 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 1.42 in. (36 mm)
A.7.8 40-WXC-C Card Specifications
The 40-WXC-C card optical specifications are listed in Table A-18.
Note For power specifications, see Table A-2.
The 40-WXC-C card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm) for a standard DWDM unit
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm) for a standard DWDM unit
A.7.9 MMU Card Specifications
The MMU card optical specifications are listed in Table A-19.
Note For power specifications, see Table A-2.
The MMU card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 8.66 in. (220.1 mm)
A.8 Optical Add/Drop Cards
This section provides specifications for the AD-IC-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.
A.8.1 AD-1C-xx.x Card Specifications
Table A-20 lists the AD-1C-xx.x optical specifications.
The AD-1C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 6-3 through Table 6-6 for this information.
The AD-1C-xx.x card has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.8.2 AD-2C-xx.x Card Specifications
Table A-21 lists the AD-2C-xx.x optical specifications.
The AD-2C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 6-3 through Table 6-6 for this information.
The AD-2C-xx.x has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.8.3 AD-4C-xx.x Card Specifications
Table A-22 lists the AD-4C-xx.x optical specifications.
|
|
|
|
|
|
|
|---|---|---|---|---|---|
Channel grid |
See Table A-23. The channel plan for the AD-4C-xx.x card is identical to the channel plan for the AD-1B-xx.x card. |
— |
— |
— |
— |
Trx filter shape |
All SOP and within whole operating temperature range |
COM Rx—xx.xx Tx |
+/-180 |
— |
pm |
Rfx filter shape |
All SOP and within whole operating temperature range |
COM Rx—Exp Tx |
— |
— |
pm |
Insertion loss |
All SOP and within whole operating temperature range (two connectors included) |
COM Rx—xx.xx Tx |
— |
5.5 |
dB |
COM Rx—yy.yy Tx |
— |
5.0 |
dB |
||
COM Rx—zz.zz Tx |
— |
4.5 |
dB |
||
COM Rx—kk.kk Tx |
— |
4.1 |
dB |
||
Insertion loss |
VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included) |
COM Rx—Exp Tx |
— |
2.7 |
dB |
Exp Rx—COM Tx |
— |
1.2 |
dB |
||
Insertion loss |
VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included) |
xx.xx Rx—COM Tx |
— |
3.9 |
dB |
yy.yy Rx—COM Tx |
— |
4.3 |
dB |
||
zz.zz Rx—COM Tx |
— |
4.5 |
dB |
||
kk.kk Rx—COM Tx |
— |
4.9 |
dB |
||
VOA dynamic range |
— |
— |
30 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
The AD-4C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 6-3 through Table 6-6 for this information.
The AD-4C-xx.x has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.8.4 AD-1B-xx.x Card Specifications
Table A-23 lists the unit names, band IDs, channel IDs, frequencies, and wavelengths assigned to the eight versions of the AD-1B-xx.x card.
Table A-24 lists AD-1B-xx.x optical specifications.
|
|
|
|
|
|
|
|---|---|---|---|---|---|
-1 dB bandwidth |
All SOP and within whole operating environmental range |
COM Rx—Band Tx |
3.6 |
— |
nm |
-1 dB bandwidth |
All SOP and within whole operating temperature range |
COM Rx—Exp Tx |
See Table A-25. |
nm |
|
Insertion loss |
All SOP and within whole operating environmental range; two connectors included, VOA set at minimum attenuation |
COM Rx—Band Tx |
— |
3.0 |
dB |
Insertion loss |
All SOP and within whole operating environmental range; two connectors included |
Exp Rx—COM Tx |
— |
1.6 |
dB |
All SOP and within whole operating environmental range; two connectors included, VOA set at its minimum attenuation |
COM Rx—Exp Tx |
— |
2.2 |
dB |
|
Insertion loss |
All SOP and within whole operating environmental range; two connectors included |
Band Rx—COM Tx |
— |
2.2 |
dB |
VOA dynamic range |
— |
— |
30 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
Table A-25 lists the range of wavelengths for the receive (express) band.
The AD-1B-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 6-3 through Table 6-6 for this information.
The AD-1B-xx.x card has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.8.5 AD-4B-xx.x Card Specifications
Table A-26 lists the unit names, band IDs, channel IDs, frequencies, and wavelengths assigned to the two versions of the card.
Table A-27 lists AD-4B-xx.x optical specifications.
|
|
|
|
|
|
|
|---|---|---|---|---|---|
-1 dB bandwidth |
All SOP and within whole operating environmental range |
COM Rx—Band Tx |
3.6 |
— |
nm |
-1 dB bandwidth |
All SOP and within whole operating temperature range |
COM Rx—Exp Tx |
Refer to Table A-28. |
nm |
|
Insertion loss |
All SOP and within whole operating environmental range; two connectors included, VOA set at minimum attenuation |
COM Rx—Band Tx |
— |
2.9 |
dB |
COM Rx—Band Tx |
— |
3.3 |
dB |
||
COM Rx—Band Tx |
— |
3.8 |
dB |
||
COM Rx—Band Tx |
— |
4.5 |
dB |
||
Insertion loss |
All SOP and within whole operating environmental range; two connectors included |
Exp Rx—COM Tx |
— |
4.9 |
dB |
All SOP and within whole operating environmental range; two connectors included, VOA set at its minimum attenuation |
COM Rx—Exp Tx |
— |
3 |
dB |
|
Insertion loss |
All SOP and within whole operating environmental range; two connectors included |
Band Rx 30.3/46.1—COM Tx |
— |
3.5 |
dB |
Band Rx 34.2/50.1—COM Tx |
— |
2.8 |
dB |
||
Band Rx 38.1/54.1—COM Tx |
— |
2.3 |
dB |
||
Band Rx 42.1/58.1—COM Tx |
— |
1.8 |
dB |
||
VOA dynamic range |
— |
— |
30 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
Table A-28 lists the range of wavelengths for the receive (express) band.
The AD-4B-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 6-3 through Table 6-6 for this information.
The AD-4B-xx.x has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.9 Transponder and Muxponder Card Specifications
This section provides specifications for the TXP_MR_10G, MXP_2.5G_10G, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_MR_2.5G, MXPP_MR_2.5G, MXP_2.5G_10E, MXP_2.5G_10E_C, MXP_2.5G_10E, TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L, MXP_MR_10DME_C, MXP_MR_10DME_L cards, and ADM-10G cards.
For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance Information document.
A.9.1 TXP_MR_10G Card Specifications
The TXP_MR_10G card has the following specifications:
•Line (trunk side)
–Bit rate:
9.95328 Gbps for OC-192/STM-64
10.70923 Gbps with ITU-T G.709 Digital Wrapper/forward error correction (FEC)
10.3125 Gbps for 10 Gigabit Ethernet (GE)
11.095 Gbps with ITU-T G.709 Digital Wrapper/FEC over 10 GE
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: 1000 ps/nm
–Loopback modes: Terminal and facility
You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10G card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10G card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10G card.
–Connectors: LC
–Compliance Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.691
•Transmitter (trunk side)
–Maximum transmitter output power: +3.5 dBm
–Minimum transmitter output power: +2.5 dBm
–Transmitter: Lithium Niobate (LN) external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10G (16 card versions, each covering two wavelengths):
–1530.33 to 1531.12 nm (two wavelengths)
–1531.90 to 1532.68 nm (two wavelengths)
–1534.25 to 1535.04 nm (two wavelengths)
–1535.82 to 1536.61 nm (two wavelengths)
–1538.19 to 1538.98 nm (two wavelengths)
–1539.77 to 1540.56 nm (two wavelengths)
–1542.14 to 1542.94 nm (two wavelengths)
–1543.73 to 1544.53 nm (two wavelengths)
–1546.12 to 1546.92 nm (two wavelengths)
–1547.72 to 1548.51 nm (two wavelengths)
–1550.12 to 1550.92 nm (two wavelengths)
–1551.72 to 1552.52 nm (two wavelengths)
–1554.13 to 1554.94 nm (two wavelengths)
–1555.75 to 1556.55 nm (two wavelengths)
–1558.17 to 1558.98 nm (two wavelengths)
–1559.79 to 1560.61 nm (two wavelengths)
•Receiver (trunk side):
–Receiver input power (no FEC, unamplified, 23 dB optical signal-to-noise ratio [OSNR], BER 1 * 10 exp - 12): -8 to -21 dBm
–Receiver input power (no FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -19 dBm
–Receiver input power (no FEC, amplified, 19 dB OSNR, BER 1 * 10 exp - 12): -8 to -20 dBm
–Receiver input power (no FEC, amplified, 19 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12):-8 to -18 dBm
–Receiver input power (FEC, unamplified, 23 dB OSNR, BER 8 * 10 exp - 5): -8 to -24 dBm
–Receiver input power (FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm, BER 8 * 10 exp - 5): -8 to -22 dBm
–Receiver input power (FEC, amplified, 9 dB OSNR, BER 8 * 10 exp - 5): -8 to -18 dBm
–Receiver input power (FEC, unamplified, 11 dB OSNR, at +/- 800 ps/nm, BER 8 * 10 exp - 5): -8 to -18 dBm
•Line (client side)
–Bit rate: 9.95328 Gbps or 10.3125 Gbps
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: Compliant with SR-1 specification for OC-192. In the case of 10 GE, the allowance is up to 10 km of single-mode fiber (SMF) dispersion.
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: Distributed feedback (DFB) laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: avalanche photodiode (APD)
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.2 MXP_2.5G_10G Card Specifications
The MXP_2.5G_10G card has the following specifications:
•Line (trunk side)
–Bit rate:
9.95328 Gbps for OC-192/STM-64
10.70923 Gbps with ITU-T G.709 Digital Wrapper/FEC
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: 1000 ps/nm
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10G card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10G card. Using direct fiber loopbacks causes irreparable damage to the MXP_2.5G_10G card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +3.5 dBm
–Minimum transmitter output power: +2.5 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10G (16 card versions, each covering two wavelengths):
–1530.33 to 1531.12 nm (two wavelengths)
–1531.90 to 1532.68 nm (two wavelengths)
–1534.25 to 1535.04 nm (two wavelengths)
–1535.82 to 1536.61 nm (two wavelengths)
–1538.19 to 1538.98 nm (two wavelengths)
–1539.77 to 1540.56 nm (two wavelengths)
–1542.14 to 1542.94 nm (two wavelengths)
–1543.73 to 1544.53 nm (two wavelengths)
–1546.12 to 1546.92 nm (two wavelengths)
–1547.72 to 1548.51 nm (two wavelengths)
–1550.12 to 1550.92 nm (two wavelengths)
–1551.72 to 1552.52 nm (two wavelengths)
–1554.13 to 1554.94 nm (two wavelengths)
–1555.75 to 1556.55 nm (two wavelengths)
–1558.17 to 1558.98 nm (two wavelengths)
–1559.79 to 1560.61 nm (two wavelengths)
•Receiver (trunk side)
–Receiver input power (no FEC, unamplified, 23 dB OSNR, BER 1 * 10 exp - 12): -8 to -21 dBm
–Receiver input power (no FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -19 dBm
–Receiver input power (no FEC, amplified, 19 dB OSNR, BER 1 * 10 exp - 12): -8 to -20 dBm
–Receiver input power (no FEC, amplified, 19 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -18 dBm
–Receiver input power (FEC, unamplified, 23 dB OSNR, BER 8 * 10 exp - 5): -8 to -24 dBm
–Receiver input power (FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm, BER 8 * 10 exp - 5): -8 to -22 dBm
–Receiver input power (FEC, amplified, 9 dB OSNR, BER 8 * 10 exp - 5): -8 to -18 dBm
–Receiver input power (FEC, unamplified, 11 dB OSNR, at +/- 800 ps/nm, BER 8 * 10 exp - 5): -8 to -18 dBm
•Line (client side)
–Bit rate: 2.48832 Gbps
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: Compliant with SR-1 specification for OC-192. In the case of 10 GE, allowance is up to 10 km of SMF fiber of dispersion.
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side): Depends on the Small Form-factor Pluggable (SFP) that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.3 TXP_MR_2.5G and TXPP_MR_2.5G Card Specifications
The TXP_MR_2.5G and TXPP_MR_2.5G cards have the following specifications:
•Line (trunk side)
–Bit rate:
2.488 Gbps for OC-48/STM-16
2.66 Gbps with ITU-T G.709 Digital Wrapper/FEC
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: 5400 ps/nm
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the TXP_MR_2.5G and TXPP_MR_2.5G cards in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_2.5G and TXPP_MR_2.5G cards. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_2.5G and TXPP_MR_2.5G cards.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +1 dBm
–Minimum transmitter output power: -4.5 dBm
–Transmitter: Direct modulated laser
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths of TXP_MR_2.5G and TXPP_MR_2.5G (eight card versions):
ITU grid blue band: 1530.334 to 1544.526 nm (four card versions covering four wavelengths each)
ITU grid red band: 1546.119 to 1560.606 nm (four card versions covering four wavelengths each)
•Receiver (trunk side, see Table A-29)
|
|
|
|
|
|
|
|---|---|---|---|---|---|
22 dB |
Off - 2R |
< 10 exp - 12 |
N/A |
- 9 to - 24 dBm |
— |
22 dB |
Off - 2R |
< 10 exp - 12 |
N/A |
- 9 to - 21 dBm |
+/- 3300ps/nm |
21 dB |
Off - 3R |
< 10 exp - 12 |
N/A |
- 9 to - 30 dBm |
— |
22 dB |
Off - 3R |
< 10 exp - 12 |
N/A |
- 9 to - 30 dBm |
+/- 1800ps/nm |
23 dB |
Off - 3R |
< 10 exp - 12 |
N/A |
- 9 to - 30 dBm |
+/- 5400ps/nm |
12 dB |
Standard- 3R |
< 10 exp - 5 |
< 10 exp - 15 |
- 9 to - 25 dBm |
— |
12 dB |
Standard- 3R |
< 10 exp - 5 |
< 10 exp - 15 |
- 9 to - 24 dBm |
+/- 1800ps/nm |
12 dB |
Standard- 3R |
< 10 exp - 5 |
< 10 exp - 15 |
- 9 to - 23 dBm |
+/- 5400ps/nm |
21 dB |
Standard- 3R |
< 10 exp - 5 |
< 10 exp - 15 |
- 9 to - 31 dBm |
— |
1 OSNR defined with 0.1 nm resolution bandwidth (RBW) |
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
•Line (client side)
–Bit rate: 8 Mbps to 2.488 Gbps
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: Based on SFP
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 850 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.4 MXP_MR_2.5G and MXPP_MR_2.5G Card Specifications
The MXP_MR_2.5G and MXPP_MR_2.5G cards have the following specifications:
•Payload configuration
–FC1G—Fibre Channel 1.06 Gbps
–FC2G—Fibre Channel 2.125 Gbps
–FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
–FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
–ESCON—Enterprise System Connection 200 Mbps
–ONE_GE—One Gigabit Ethernet 1.125 Gbps
–Mixed configurations up to maximum line rate of 2.5 Gbps (for example, if you have a port configured for FC2G, you cannot use another port at the same time). See the "MXP_MR_2.5G and MXPP_MR_2.5G Cards" section for more information on mixed-mode operation.
•Client ports: 8x SFP
•Performance monitoring (PM) for all interfaces
•Buffer-to-buffer credit management for distance extension
•Line (trunk side)
–Bit rate: 2.488 Gbps for OC-48/STM-16
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: 6000 ps/nm
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_2.5G and MXPP_MR_2.5G cards in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_2.5G and MXPP_MR_2.5G cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_2.5G and MXPP_MR_2.5G cards.
–Connectors: LC
•Transmitter (trunk side)
–Transmit power: +3 +/- 1 dBm with MXP_MR_2.5G card, and +/- 1 dBm with MXPP_MR_2.5G card
–50-GHz DWDM migration ready (the wavelength deviation is less than +/- 0.040 nm through wavelocker deployment)
–Four-channel wavelength tunability at 100-GHz spacing
–Transmitter maximum return reflectance: -27 dB
–Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
–Minimum side mode suppression ratio: 30 dB
–Transmitter is a direct modulated laser
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths of the TXP_MR_2.5G and TXPP_MR_2.5G cards (eight card versions):
–ITU grid blue band: 1530.334 to 1544.526 nm (four card versions, four wavelengths each)
–ITU grid red band: 1546.119 to 1560.606 nm (four card versions, four wavelengths each)
•Receiver (trunk side, see Table A-30)
|
|
|
|
|
|
|
|---|---|---|---|---|---|
17 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 23 dBm |
— |
17 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 22 dBm |
+/- 1800 ps/nm |
17 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 21 dBm |
+/- 5400 ps/nm |
18 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 23 dBm |
+/- 1800 ps/nm |
19 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 23 dBm |
+/- 5400 ps/nm |
21 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 30 dBm |
— |
21 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 29 dBm |
+/- 1800 ps/nm |
21 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 28 dBm |
+/- 5400 ps/nm |
22 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 30 dBm |
+/- 1800 ps/nm |
23 dB |
N/A |
< 10 exp - 12 |
N/A |
- 9 to - 30 dBm |
+/- 5400 ps/nm |
1 OSNR defined with 0.1 nm RBW |
–Receiver sensitivity -28 dBm, BER 1 * 10 exp - 12
–Receiver overload is equal to or exceeds -8 dBm
–Receiver maximum reflectance of -27 dB
•Line (client side)
–Bit rate: 200Mbps or 1.06 Gbps to 2.125 Gbps per client
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: 1600 ps/nm
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.25 lb (1.02 kg)
A.9.5 MXP_2.5G_10E Card Specifications
The MXP_2.5G_10E card has the following specifications:
•Line (trunk side)
–Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E card. Using direct fiber loopbacks causes irreparable damage to the MXP_2.5G_10E card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10E (eight card versions):
ITU grid blue band:
–1530.33 to 1533.07 nm (four channels)
–1534.25 to 1537.00 nm (four channels)
–1538.19 to 1540.95 nm (four channels)
–1542.14 to 1544.92 nm (four channels)
ITU grid red band:
–1546.12 to 1548.92 nm (four channels)
–1550.12 to 1552.93 nm (four channels)
–1554.13 to 1556.96 nm (four channels)
–1558.17 to 1561.01 nm (four channels)
•Receiver (trunk side, see Table A-31)
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
|
|
|
|
|
|
|
|---|---|---|---|---|---|
30 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1200 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1000 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 22 dBm |
— |
17 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
15 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
15 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
14 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
1 OSNR defined with 0.1 nm RBW 2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm) |
•Line (client side)
–Bit rate: 2.5 Gbps per port (OC-48/STM-16)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.6 MXP_2.5G_10E_C Card Specifications
The MXP_2.5G_10E_C card has the following specifications:
•Line (trunk side)
–Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E_C card. Using direct fiber loopbacks causes irreparable damage to the card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10E_C card:
There is a single version of the MXP_2.5G_10E_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-32.
•Receiver (trunk side, see Table A-33)
|
|
|
|
|
|
|
|---|---|---|---|---|---|
30 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1200 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1000 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 22 dBm |
— |
17 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
15.5 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
14 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
12 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
1 OSNR defined with 0.1 nm RBW 2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm) |
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side)
–Bit rate: 2.5 Gbps per port (OC-48/STM-16)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.7 MXP_2.5G_10E_L Card Specifications
The MXP_2.5G_10E_L card has the following specifications:
•Line (trunk side)
–Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E_L card. Using direct fiber loopbacks causes irreparable damage to the card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10E_L card:
There is a single version of the MXP_2.5G_10E_L card. It is tunable across 80 wavelengths in the L band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-34.
•Receiver (trunk side, see Table A-35)
|
|
|
|
|
|
|
|---|---|---|---|---|---|
30 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1200 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1000 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 22 dBm |
— |
17 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
15.5 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
15 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
13 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
1 OSNR defined with 0.1 nm RBW 2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm) |
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1570 to 1604 nm
•Line (client side)
–Bit rate: 2.5 Gbps per port (OC-48/STM-16)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.8 MXP_MR_10DME_C Card Specifications
The MXP_MR_10DME_C card has the following specifications:
•Payload configuration
–FC1G—Fibre Channel 1.06 Gbps
–FC2G—Fibre Channel 2.125 Gbps
–FC4G—Fibre Channel 4.25 Gbps
–FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
–FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
–FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)
–ONE_GE—One Gigabit Ethernet 1.125 Gbps
–Mixed configurations up to maximum line rate of 10.0 Gbps. See the "MXP_MR_10DME_C and MXP_MR_10DME_L Cards" section for more information on mixed-mode operation.
•Client ports: 8x SFP
•Line (trunk side)
–Bit rate: 2.488 Gbps for OC-48/STM-16, 9.952 Gbps for OC-192/STM-64
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DME_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DME_C cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DME_C cards.
–Connectors: LC
•Transmitter (trunk side)
–Minimum output power: +3 dBm
–Maximum output power: +6 dBm
–Minimum Single-Mode Suppression Ratio (SMSR): 30 dB
–Minimum optical extinction ratio: 10 dB
–41 wavelength tunability at 100-GHz spacing
–Receiver maximum return reflectance (Rx return loss): -27 dB
–Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
–Minimum side mode suppression ratio: 30 dB
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
–For available wavelengths for the MXP_MR_10DME_C card, see Table 8-29.
•For the receiver trunk side, see Table A-36:
|
|
|
|
|
|
|
|
|
|---|---|---|---|---|---|---|---|
None |
23 dB |
< 10 exp - 12 |
— |
-8 to -20 dBm |
+/- 1200 ps/nm |
2 dBm |
— |
19 dB |
< 10 exp - 12 |
— |
-9 to -22 dBm |
+/- 1000 ps/nm |
2 dBm |
— |
|
FEC |
10 dB |
< 10 exp - 5 |
< 10 exp - 15 |
-8 to -18 dBm |
+/- 800 ps/nm |
— |
1.5 dB |
Enhanced FEC |
19 dB |
< 10 exp - 4 |
< 10 exp - 15 |
-8 to -26 dBm |
+/- 800 ps/nm |
2 dBm |
2 dB |
8 dB |
< 10 exp - 4 |
< 10 exp - 15 |
-8 to -18 dBm |
+/- 800 ps/nm |
2 dBm |
1.5 dB |
1 OSNR defined with 0.5 nm RBW |
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side)
–Bit rate: 1.06 Gbps to 4.25 Gbps per client
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: Based on SFP
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm or 850nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.25 lb (1.02 kg)
A.9.9 MXP_MR_10DME_L Card Specifications
The MXP_MR_10DME_L card has the following specifications:
•Payload configuration
–FC1G—Fibre Channel 1.06 Gbps
–FC2G—Fibre Channel 2.125 Gbps
–FC4G—Fibre Channel 4.25 Gbps
–FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
–FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
–FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)
–ONE_GE—One Gigabit Ethernet 1.125 Gbps
–Mixed configurations up to maximum line rate of 10.0 Gbps. See the "MXP_MR_10DME_C and MXP_MR_10DME_L Cards" section for more information on mixed-mode operation.
•Client ports: 8x SFP
•Line (trunk side)
–Bit rate: 2.488 Gbps for OC-48/STM-16, 9.952 Gbps for OC-192/STM-64
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DME_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DME_L cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DME_L cards.
–Connectors: LC
•Transmitter (trunk side)
–Minimum output power: +3 dBm
–Maximum output power: +6 dBm
–Minimum SMSR: 30 dB
–Minimum optical extinction ratio: 10.5 dB
–40 wavelength tunability at 100-GHz spacing, 80 wavelength tunability at 50-GHz spacing
–Receiver maximum return reflectance (Rx return loss): -27 dB
–Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
–Minimum side mode suppression ratio: 30 dB
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
–For the currently available wavelengths for the MXP_MR_10DME_L card, see Table 8-30.
•Table A-37 provides the receiver trunk side specifications:
|
|
|
|
|
|
|
|
|
|---|---|---|---|---|---|---|---|
None |
23 dB |
< 10 exp - 12 |
— |
-8 to -19 dBm |
+/- 1200 ps/nm |
2 dBm |
— |
19 dB |
< 10 exp - 12 |
— |
-9 to -19 dBm |
+/- 1000 ps/nm |
2 dBm |
— |
|
FEC |
10 dB |
< 10 exp - 5 |
< 10 exp - 15 |
-8 to -18 dBm |
+/- 800 ps/nm |
— |
1.5 dB |
Enhanced FEC |
19 dB |
< 10 exp - 4 |
< 10 exp - 15 |
-8 to -26 dBm |
+/- 800 ps/nm |
— |
2 dB |
8 dB |
< 10 exp - 4 |
< 10 exp - 15 |
-8 to -18 dBm |
+/- 800 ps/nm |
— |
1.5 dB |
1 OSNR defined with 0.5 nm RBW |
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1570 to 1604 nm
•Line (client side)
–Bit rate: 1.06 Gbps to 2.125 Gbps per client
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: Based on SFP
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm or 850nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.25 lb (1.02 kg)
A.9.10 TXP_MR_10E Card Specifications
The TXP_MR_10E card has the following specifications:
•Line (trunk side)
–Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm for C band and +2 dBm for L band
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10E:
C-band frequency plan (eight card versions, each with four tunable channels on the ITU 100-GHz grid):
–1530.33 to 1533.07 nm (four channels)
–1534.25 to 1537.00 nm (four channels)
–1538.19 to 1540.95 nm (four channels)
–1542.14 to 1544.92 nm (four channels)
–1546.12 to 1548.92 nm (four channels)
–1550.12 to 1552.93 nm (four channels)
–1554.13 to 1556.96 nm (four channels)
–1558.17 to 1561.01 nm (four channels)
L-band frequency plan (five card versions, each with eight tunable channels on the ITU 50-GHz grid):
–1577.44 to 1580.35 nm (eight channels)
–1580.77 to 1583.69 nm (eight channels)
–1584.11 to 1587.04 nm (eight channels)
–1587.46 to 1590.41 nm (eight channels)
–1590.83 to 1593.79 nm (eight channels)
•Receiver (trunk side, see Table A-38)
|
|
|
|
|
|
|
|---|---|---|---|---|---|
30 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1200 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+ - 1000 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 22 dBm |
— |
17 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
15 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
15 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
14 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
1 OSNR defined with 0.1 nm RBW 2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm) |
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
•Line (client side):
–10-Gigabit Small Form-factor Pluggable (XFP)-based SR
–Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 6.6 ps/nm
–Loopback modes: Terminal and facility
–Connectors: LC
–Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, ITU-T G.691
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: DFB laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.11 TXP_MR_10E_C Card Specifications
The TXP_MR_10E_C card has the following specifications:
•Line (trunk side)
–Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E_C card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E_C card.
–Connectors: LC
–Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, and ITU-T G.709
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10E_C card:
There is a single version of the TXP_MR_10E_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-39.
•Receiver (trunk side, see Table A-40)
|
|
|
|
|
|
|
|---|---|---|---|---|---|
30 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1200 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+ - 1000 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 22 dBm |
— |
17 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
15.5 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
14 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
12 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
1 OSNR defined with 0.1 nm RBW 2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm) |
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side):
–XFP-based SR
–Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 6.6 ps/nm
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: DFB laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.12 TXP_MR_10E_L Card Specifications
The TXP_MR_10E_L card has the following specifications:
•Line (trunk side)
–Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E_L card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E_L card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +2 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10E_L card:
There is a single version of the TXP_MR_10E_L card. It is tunable across 80 wavelengths in the L band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-41.
•Receiver (trunk side, see Table A-42)
|
|
|
|
|
|
|
|---|---|---|---|---|---|
30 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+/- 1200 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 20 dBm |
+ - 1000 ps/nm |
26 dB |
Off |
< 10 exp - 12 |
N/A |
- 8 to - 22 dBm |
— |
17 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
15.5 dB |
Standard |
< 10 exp - 5 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
15 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
+/- 800 ps/nm |
13 dB |
Enhanced |
< 7 x 10 exp - 4 |
< 10 exp - 15 |
- 8 to - 18 dBm |
— |
1 OSNR defined with 0.1 nm RBW 2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm) |
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1570 to 1604 nm
•Line (client side):
–XFP-based SR
–Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 6.6 ps/nm
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: DFB laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.9.13 ADM-10G Card Specifications
The ADM-10G card has the following specifications:
•Line:
–Bit rate: OC-3/STM-1, 155.520 Mb/s; OC-12/STM-3, 622.08 Mb/s; OC-48/STM-16, 2488.32 Mb/s; OC-192/STM-64, 9.95328 Gbps.
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: up to 3600 ps/nm
–Loopback modes: Terminal, facility, and cross-connect
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +2 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1570 to 1604 nm
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 5.07 lb (2.3 kg)
A.9.14 GE_XP and 10GE_XP Card Specifications
The GE_XP and 10GE-XP cards have the following specifications:
•Line (trunk side)
–Bit rate: 11.1 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode) or 10.3125 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode disabled)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: - 500 to 1600 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the GE_XP card in a loopback on the trunk port. Do not use direct fiber loopbacks with the GE_XP card. Using direct fiber loopbacks causes irreparable damage to the GE_XP card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +3 dBm
–Minimum transmitter output power: -1 dBm
–Transmitter: EML laser
–Wavelength stability (drift): +/- 100 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of GE_XP and 10GE_XP: C Band, 100 GHz spacing.
•Receiver (trunk side, see Table A-43)
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
|
|
|
|
|
|
|
|---|---|---|---|---|---|
30 dB |
Off |
1.00E - 12 |
N/A |
- 7 to - 23 dBm |
— |
30 dB |
Off |
1.00E - 12 |
N/A |
- 7 to - 20 dBm |
- 500 to 1600 ps/nm |
24 dB |
Off |
1.00E - 12 |
N/A |
- 7 to - 18 dBm |
— |
27 dB |
Off |
1.00E - 12 |
N/A |
- 7 to - 18 dBm |
- 500 to 1600 ps/nm |
18 dB |
Standard |
1.00E - 05 |
1.00E - 15 |
- 7 to - 18 dBm |
— |
19 dB |
Standard |
1.00E - 05 |
1.00E - 15 |
- 7 to - 18 dBm |
- 500 to 1600 ps/nm |
30 dB |
Enhanced |
1.00E - 04 |
1.00E - 15 |
- 7 to - 27 dBm |
— |
30 dB |
Enhanced |
1.00E - 04 |
1.00E - 15 |
- 7 to - 24 dBm |
- 500 to 1600 ps/nm |
15 dB |
Enhanced |
1.00E - 04 |
1.00E - 15 |
- 7 to - 18 dBm |
— |
15 dB |
Enhanced |
1.00E - 04 |
1.00E - 15 |
- 7 to - 18 dBm |
- 500 to 1600 ps/nm |
1 OSNR defined with 0.1 nm RBW 2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm) |
•Line (client side)
–Bit rate: 1.125Gbps (GE) or 10.3125Gbps (10GE)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode or 850-nm multimode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.992 in. (330 mm)
–Width: 10GE_XP and 10GE_XPE: 0.921 in. (23.4 mm)
GE_XP and GE_XPE: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.448 in. (240 mm)
–Depth with backplane connector: tbd in. (tbd mm)
–Weight not including clam shell: 10GE-XP, 1.04 kg; GE-XP, 1.36 kg.
A.10 Mesh Patch Panel Specifications
This section provides specifications for the PP-MESH-4 and PP-MESH-8 patch panels.
A.10.1 PP-MESH-4 Patch Panel Specifications
The PP-MESH-4 patch panel optical specifications are listed in Table A-44.
1 Under all SOPs and all operating environmental conditions 2 Values are referenced with connector loss (LC=0.3 dB, MPO=0.5dB) |
The PP-MESH-4 patch panel has the following additional specifications:
•Environmental
–Operating temperature: +23 to +149 degrees Fahrenheit (-5 to +65 degrees Celsius)
–Operating humidity: 5 to 95 percent, noncondensing
•Dimensions
–Height: 17.42 in. (442.5 mm)
–Width: 3.457 in. (87.8 mm)
–Depth: 11.025 in. (280 mm)
A.10.2 PP-MESH-8 Patch Panel Specifications
The PP-MESH-8 patch panel optical specifications are listed in Table A-45.
1 Under all SOPs and all operating environmental conditions 2 Values are referenced with connector loss (LC=0.3 dB, MPO=0.5dB) |
The PP-MESH-8 patch panel has the following additonal specifications:
•Environmental
–Operating temperature: +23 to +149 degrees Fahrenheit (-5 to +65 degrees Celsius)
–Operating humidity: 5 to 95 percent, noncondensing
•Dimensions
–Height: 17.42 in. (442.5 mm)
–Width: 3.457 in. (87.8 mm)
–Depth: 11.025 in. (280 mm)
A.11 SFP and XFP Specifications
Note Use hardware version 2.0 DWDM SFP for MSTP units.
See the Installing the GBIC, SFP, SFP+, XFP, CXP, and CFP Optical Modules in Cisco ONS Platforms for SFP and XFP specifications.
Feedback