Contents

IPv6: RIPng VRF-Aware Support

The IPv6: RIPng VRF-Aware Support feature uses separate routing tables for every provider edge-customer edge (PE-CE) scenario, thus allowing improved route protection, modularity, and a potential reduction in the size of the routing table.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Information About IPv6: RIPng VRF-Aware Support

IPv6 Routing: RIP for IPv6

IPv6 Routing Information Protocol (RIP) functions the same and offers the same benefits as IPv4 RIP. RIP enhancements for IPv6, detailed in RFC 2080, include support for IPv6 addresses and prefixes and the use of the all-RIP-devices multicast group address, FF02::9, as the destination address for RIP update messages.

IPv6: RIPng VRF-Aware Support

When not in Virtual Routing and Forwarding (VRF) mode, every IPv6 Routing Information Protocol (RIP)—also know as RIP Next Generation (RIPng)—process and the configuration associated with it, keeps all the routes in the same routing table. In other routing protocols, it is often required to keep the protocol-related routes stored in separate routing tables.

The IPv6: RIPng VRF-Aware Support feature enables isolation, modularity, and potential performance improvement by reducing the number of routes stored in a single routing table. It also allows a network administrator to create different RIP routing tables and share the same protocol configuration stored in a single RIP protocol configuration block.

How to Configure IPv6: RIPng VRF-Aware Support

Configuring IPv6: RIPng VRF-Aware Support

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    ipv6 unicast-routing

    4.    vrf definition vrf-name

    5.    address-family ipv6

    6.    exit

    7.    exit

    8.    ipv6 rip vrf-mode enable

    9.    ipv6 router rip rip-process-name

    10.    exit

    11.    interface type number

    12.    vrf forwarding vrf-name

    13.    ipv6 enable

    14.    ipv6 rip rip-process-name enable

    15.    end

    16.    debug ipv6 rip vrf vrf-name

    17.    show ipv6 rip vrf vrf-name next-hops

    18.    show ipv6 rip vrf vrf-name database


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Device # configure terminal
     

    Enters global configuration mode.

     
    Step 3ipv6 unicast-routing


    Example:
    Device (config)# ipv6 unicast-routing
     

    Enables the forwarding of IPv6 unicast datagrams.

     
    Step 4vrf definition vrf-name


    Example:
    Device(config)# vrf definition vrf1
     

    Configures a virtual routing and forwarding (VRF) routing table instance and enters VRF configuration mode.

     
    Step 5address-family ipv6


    Example: 
    Device(config-vrf)# address-family ipv6
     

    Enters VRF address family configuration mode and enables IPv6 address prefixes.

     
    Step 6exit


    Example: 
    Device(config-vrf-af)# exit
     

    Exits VRF address family configuration mode and returns to VRF configuration mode.

     
    Step 7exit


    Example: 
    Device(config-vrf)# exit
     

    Exits VRF configuration mode and returns to global configuration mode.

     
    Step 8 ipv6 rip vrf-mode enable


    Example:
    Device (config)# ipv6 rip vrf-mode enable
     

    Enables VRF support for IPv6 RIP routing and enters RTR entry configuration mode.

     
    Step 9 ipv6 router rip rip-process-name


    Example:
    Device (config)# ipv6 router rip myrip
     

    Creates an IPv6 Routing Information Protocol (RIP) routing process instance.

     
    Step 10 exit


    Example:
    Device (config-rtr)# exit
     

    Exits RTR entry configuration mode and returns to global configuration mode.

     
    Step 11 interface type number


    Example:
    Device (config)# interface Ethernet 0/0
     

    Specifies the interface type and number and enters interface configuration mode.

     
    Step 12vrf forwarding vrf-name


    Example:
    Device(config-if)# vrf forwarding vrf1
     

    Binds the interface to the specified VRF routing instance table and removes all the Layer 3 interface configuration that is available when the command is entered.

     
    Step 13ipv6 enable


    Example:
    Device(config-if)# ipv6 enable
     

    Enables IPv6 on the interface.

     
    Step 14ipv6 rip rip-process-name enable


    Example:
    Device(config-if)# ipv6 rip myrip enable
     

    Enables an IPv6 RIP routing process on the interface.

     
    Step 15end


    Example: 
    Device (config-if)# end
     

    Exits interface configuration mode and returns to privileged EXEC mode.

     
    Step 16debug ipv6 rip vrf vrf-name


    Example:
    Device# debug ipv6 rip vrf vrf1
     

    Displays debugging information related to VRF support for the specified IPv6 RIP VRF routing table instance.

     
    Step 17show ipv6 rip vrf vrf-name next-hops


    Example: 
    Device# show ipv6 rip vrf vrf1 next-hops
     

    Displays the next hops in the specified VRF RIPng routing table.

     
    Step 18show ipv6 rip vrf vrf-name database


    Example: 
    Device# show ipv6 rip vrf vrf1 database
     

    Displays the associated RIP local routing information base (RIB).

     

    Configuration Examples for IPv6: RIPng VRF-Aware Support

    Example: Configuring IPv6: RIPng VRF-Aware Support

    Device> enable
Device# configure terminal 
Device(config)# ipv6 unicast-routing
Device(config)# vrf definition vrf1 
Device(config-vrf)# address-family ipv6
Device(config-vrf-af)# exit
Device(config-vrf)# exit
Device(config)# ipv6 rip vrf-mode enable 
Device(config)# ipv6 router rip myrip
Device(config-rtr)# exit
Device(config)# interface Ethernet 0/0
Device(config-if)# vrf forwarding vrf1
Device(config-if)# ipv6 enable
Device(config-if)# ipv6 rip myrip enable 
Device(config-if)# end

    Example: Verifying IPv6: RIPng VRF-Aware Support

    Device> debug ipv6 rip vrf vrf1

RIP Routing Protocol debugging is on for vrf vrf1
Sending:
*Mar 15 11:23:08.508: RIPng: Sending multicast update on Ethernet0/0 for vrf for vrf vrf1
*Mar 15 11:23:08.508: src=2001:DB8:0:1:FFFF:1234::5
*Mar 15 11:23:08.508: dst=2001:DB8:0:1::1 (Ethernet0/0)
*Mar 15 11:23:08.508: sport=521, dport=521, length=52
*Mar 15 11:23:08.508: command=2, version=1, mbz=0, #rte=2
*Mar 15 11:23:08.508: tag=0, metric=1, prefix=6000::/64
*Mar 15 11:23:08.508: tag=0, metric=1, prefix=2000::/64
*Mar 15 11:23:08.508: RIPng: Packet waiting
*Mar 15 11:23:08.508: RIPng: Process vrf received own response on Loopback1
Receiving
*Mar 15 11:23:20.316: RIPng: Packet waiting
*Mar 15 11:23:20.316: RIPng: response received from FE80::A8BB:CCFF:FE00:7C00 on Ethernet0/0
for vrf
*Mar 15 11:23:20.316: src=2001:DB8:0:1:FFFF:1234::4 (Ethernet0/0)
*Mar 15 11:23:20.316: dst=2001:DB8::1
*Mar 15 11:23:20.316: sport=521, dport=521, length=32
*Mar 15 11:23:20.316: command=2, version=1, mbz=0, #rte=1
*Mar 15 11:23:20.316: tag=0, metric=1, prefix=AAAA::/64


    Device> show ipv6 rip vrf vrf1	database

RIP VRF "vrf1", local RIB
FE80::A8BB:CCFF:FE00:7C00/Ethernet0/0 [1 paths]



    Device> show ipv6 rip vrf vrf1 next-hops

RIP VRF "vrf1", Next Hops
 AAAA::/64, metric 2, installed
Ethernet0/0/FE80::A8BB:CCFF:FE00:7C00, expires in 177 secs

    Additional References for IPv6: RIPng VRF-Aware Support

    Related Documents

    Related Topic Document Title

    Cisco IOS Commands

    Cisco IOS Master Command List, All Releases

    IP Routing: RIP commands

    		 Cisco IOS IP Routing: RIP Command Reference

    IPv6 Routing: RIP for IPv6

    Cisco IOS IP Routing: RIP Configuration Guide

    Standards and RFCs

    Standard/RFC Title

    RFC 2080

    RIPng for IPv6

    Technical Assistance

    Description Link

    The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

    To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

    Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

    http:/​/​www.cisco.com/​support

    Feature Information for IPv6: RIPng VRF-Aware Support

    The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

    Table 1 IPv6: RIPng VRF-Aware Support

    Feature Name

    Releases

    Feature Information

    IPv6: RIPng VRF-Aware Support

    15.3(3)M

    When not virtual routing and forwarding (VRF) aware, IPv6 Routing Information Protocol (RIP), also known as RIP Next Generation (RIPng), works only with routes that are available in the default global routing table. When operating in VRF mode, RIPng, creates a separate routing table for each VRF instance. The IPv6: RIPng VRF-Aware Support feature enables the availability of separate routing tables for every provider edge-customer edge (PE-CE) scenario, thus allowing improved route protection, modularity, and a potential reduction in the size of the routing table.

    The following commands were introduced or modified: clear ipv6 rip,debug ipv6 rip , ipv6 rip vrf-mode enable, and show ipv6 rip.

    IPv6: RIPng VRF-Aware Support

    IPv6: RIPng VRF-Aware Support

    The IPv6: RIPng VRF-Aware Support feature uses separate routing tables for every provider edge-customer edge (PE-CE) scenario, thus allowing improved route protection, modularity, and a potential reduction in the size of the routing table.

    Finding Feature Information

    Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

    Information About IPv6: RIPng VRF-Aware Support

    IPv6 Routing: RIP for IPv6

    IPv6 Routing Information Protocol (RIP) functions the same and offers the same benefits as IPv4 RIP. RIP enhancements for IPv6, detailed in RFC 2080, include support for IPv6 addresses and prefixes and the use of the all-RIP-devices multicast group address, FF02::9, as the destination address for RIP update messages.

    IPv6: RIPng VRF-Aware Support

    When not in Virtual Routing and Forwarding (VRF) mode, every IPv6 Routing Information Protocol (RIP)—also know as RIP Next Generation (RIPng)—process and the configuration associated with it, keeps all the routes in the same routing table. In other routing protocols, it is often required to keep the protocol-related routes stored in separate routing tables.

    The IPv6: RIPng VRF-Aware Support feature enables isolation, modularity, and potential performance improvement by reducing the number of routes stored in a single routing table. It also allows a network administrator to create different RIP routing tables and share the same protocol configuration stored in a single RIP protocol configuration block.

    How to Configure IPv6: RIPng VRF-Aware Support

    Configuring IPv6: RIPng VRF-Aware Support

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    ipv6 unicast-routing

      4.    vrf definition vrf-name

      5.    address-family ipv6

      6.    exit

      7.    exit

      8.    ipv6 rip vrf-mode enable

      9.    ipv6 router rip rip-process-name

      10.    exit

      11.    interface type number

      12.    vrf forwarding vrf-name

      13.    ipv6 enable

      14.    ipv6 rip rip-process-name enable

      15.    end

      16.    debug ipv6 rip vrf vrf-name

      17.    show ipv6 rip vrf vrf-name next-hops

      18.    show ipv6 rip vrf vrf-name database


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Device # configure terminal
       

      Enters global configuration mode.

       
      Step 3ipv6 unicast-routing


      Example:
      Device (config)# ipv6 unicast-routing
       

      Enables the forwarding of IPv6 unicast datagrams.

       
      Step 4vrf definition vrf-name


      Example:
      Device(config)# vrf definition vrf1
       

      Configures a virtual routing and forwarding (VRF) routing table instance and enters VRF configuration mode.

       
      Step 5address-family ipv6


      Example: 
      Device(config-vrf)# address-family ipv6
       

      Enters VRF address family configuration mode and enables IPv6 address prefixes.

       
      Step 6exit


      Example: 
      Device(config-vrf-af)# exit
       

      Exits VRF address family configuration mode and returns to VRF configuration mode.

       
      Step 7exit


      Example: 
      Device(config-vrf)# exit
       

      Exits VRF configuration mode and returns to global configuration mode.

       
      Step 8 ipv6 rip vrf-mode enable


      Example:
      Device (config)# ipv6 rip vrf-mode enable
       

      Enables VRF support for IPv6 RIP routing and enters RTR entry configuration mode.

       
      Step 9 ipv6 router rip rip-process-name


      Example:
      Device (config)# ipv6 router rip myrip
       

      Creates an IPv6 Routing Information Protocol (RIP) routing process instance.

       
      Step 10 exit


      Example:
      Device (config-rtr)# exit
       

      Exits RTR entry configuration mode and returns to global configuration mode.

       
      Step 11 interface type number


      Example:
      Device (config)# interface Ethernet 0/0
       

      Specifies the interface type and number and enters interface configuration mode.

       
      Step 12vrf forwarding vrf-name


      Example:
      Device(config-if)# vrf forwarding vrf1
       

      Binds the interface to the specified VRF routing instance table and removes all the Layer 3 interface configuration that is available when the command is entered.

       
      Step 13ipv6 enable


      Example:
      Device(config-if)# ipv6 enable
       

      Enables IPv6 on the interface.

       
      Step 14ipv6 rip rip-process-name enable


      Example:
      Device(config-if)# ipv6 rip myrip enable
       

      Enables an IPv6 RIP routing process on the interface.

       
      Step 15end


      Example: 
      Device (config-if)# end
       

      Exits interface configuration mode and returns to privileged EXEC mode.

       
      Step 16debug ipv6 rip vrf vrf-name


      Example:
      Device# debug ipv6 rip vrf vrf1
       

      Displays debugging information related to VRF support for the specified IPv6 RIP VRF routing table instance.

       
      Step 17show ipv6 rip vrf vrf-name next-hops


      Example: 
      Device# show ipv6 rip vrf vrf1 next-hops
       

      Displays the next hops in the specified VRF RIPng routing table.

       
      Step 18show ipv6 rip vrf vrf-name database


      Example: 
      Device# show ipv6 rip vrf vrf1 database
       

      Displays the associated RIP local routing information base (RIB).

       

      Configuration Examples for IPv6: RIPng VRF-Aware Support

      Example: Configuring IPv6: RIPng VRF-Aware Support

      Device> enable
Device# configure terminal 
Device(config)# ipv6 unicast-routing
Device(config)# vrf definition vrf1 
Device(config-vrf)# address-family ipv6
Device(config-vrf-af)# exit
Device(config-vrf)# exit
Device(config)# ipv6 rip vrf-mode enable 
Device(config)# ipv6 router rip myrip
Device(config-rtr)# exit
Device(config)# interface Ethernet 0/0
Device(config-if)# vrf forwarding vrf1
Device(config-if)# ipv6 enable
Device(config-if)# ipv6 rip myrip enable 
Device(config-if)# end

      Example: Verifying IPv6: RIPng VRF-Aware Support

      Device> debug ipv6 rip vrf vrf1

RIP Routing Protocol debugging is on for vrf vrf1
Sending:
*Mar 15 11:23:08.508: RIPng: Sending multicast update on Ethernet0/0 for vrf for vrf vrf1
*Mar 15 11:23:08.508: src=2001:DB8:0:1:FFFF:1234::5
*Mar 15 11:23:08.508: dst=2001:DB8:0:1::1 (Ethernet0/0)
*Mar 15 11:23:08.508: sport=521, dport=521, length=52
*Mar 15 11:23:08.508: command=2, version=1, mbz=0, #rte=2
*Mar 15 11:23:08.508: tag=0, metric=1, prefix=6000::/64
*Mar 15 11:23:08.508: tag=0, metric=1, prefix=2000::/64
*Mar 15 11:23:08.508: RIPng: Packet waiting
*Mar 15 11:23:08.508: RIPng: Process vrf received own response on Loopback1
Receiving
*Mar 15 11:23:20.316: RIPng: Packet waiting
*Mar 15 11:23:20.316: RIPng: response received from FE80::A8BB:CCFF:FE00:7C00 on Ethernet0/0
for vrf
*Mar 15 11:23:20.316: src=2001:DB8:0:1:FFFF:1234::4 (Ethernet0/0)
*Mar 15 11:23:20.316: dst=2001:DB8::1
*Mar 15 11:23:20.316: sport=521, dport=521, length=32
*Mar 15 11:23:20.316: command=2, version=1, mbz=0, #rte=1
*Mar 15 11:23:20.316: tag=0, metric=1, prefix=AAAA::/64


      Device> show ipv6 rip vrf vrf1	database

RIP VRF "vrf1", local RIB
FE80::A8BB:CCFF:FE00:7C00/Ethernet0/0 [1 paths]



      Device> show ipv6 rip vrf vrf1 next-hops

RIP VRF "vrf1", Next Hops
 AAAA::/64, metric 2, installed
Ethernet0/0/FE80::A8BB:CCFF:FE00:7C00, expires in 177 secs

      Additional References for IPv6: RIPng VRF-Aware Support

      Related Documents

      Related Topic Document Title

      Cisco IOS Commands

      Cisco IOS Master Command List, All Releases

      IP Routing: RIP commands

      		 Cisco IOS IP Routing: RIP Command Reference

      IPv6 Routing: RIP for IPv6

      Cisco IOS IP Routing: RIP Configuration Guide

      Standards and RFCs

      Standard/RFC Title

      RFC 2080

      RIPng for IPv6

      Technical Assistance

      Description Link

      The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

      To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

      Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

      http:/​/​www.cisco.com/​support

      Feature Information for IPv6: RIPng VRF-Aware Support

      The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

      Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

      Table 1 IPv6: RIPng VRF-Aware Support

      Feature Name

      Releases

      Feature Information

      IPv6: RIPng VRF-Aware Support

      15.3(3)M

      When not virtual routing and forwarding (VRF) aware, IPv6 Routing Information Protocol (RIP), also known as RIP Next Generation (RIPng), works only with routes that are available in the default global routing table. When operating in VRF mode, RIPng, creates a separate routing table for each VRF instance. The IPv6: RIPng VRF-Aware Support feature enables the availability of separate routing tables for every provider edge-customer edge (PE-CE) scenario, thus allowing improved route protection, modularity, and a potential reduction in the size of the routing table.

      The following commands were introduced or modified: clear ipv6 rip,debug ipv6 rip , ipv6 rip vrf-mode enable, and show ipv6 rip.